Volt 130 Series Operating and safety instructions

VOLT®Low Voltage Landscape Lighting

The Tank

130 Series

Installation & Maintenance Guide

Specications and product details subject to change without notice.

served. [email protected] • 813.978.3700

Help Hotline:

1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®The Tank

130 Series

Important: Please Read Before Installation

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

This luminaire is intended for installation in accordance with local codes and

the National Electric Code (NEC). Failure to adhere to these codes and instruc-

tions may result in serious injury, property damage and void the warranty.

These instructions do not intend to cover all variations in installation, opera-

tion maintenance or mounting situation.

1. Make sure that the power is turned OFF before installing or servicing this

luminaire.

2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)

or more from pool, spa or fountain.

3. This luminaire is intended to be used only with a power supply (trans-

former) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. Wiring connections must be made with wire connectors that is suitable

for outdoor use.

5. Position the low voltage wire and wire connector so that it is located

within 6 inches (15.2 cm) from a building structure, a luminaire or tting.

6. The main low voltage cable is intended for shallow burial - less than 6

inches (152 mm)

7. If additional lengths of low voltage cable is required, please contact

www.voltlighting.com or call 1-813-978-3700.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamp gets HOT quickly! Contact only switch/plug when turning on.

3. Do not touch the hot lens, guard or enclosure.

4. Keep lamp away from materials that may burn.

5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-

age lamp.

6. Do not operate the luminaire tting with a missing or damage shield.

SAVE THESE INSTRUCTIONS

www.voltlighting.com

Product Dimensions

A. (1) Stake

B. (1) Luminaire

C. (1) Shield

Install Stake

customersupport@voltlighting.com • 813.978.3700

Determine desired location for mounting lumi-

naire. Hammer stake into ground until ange

of stake is ush to grade. To avoid damage to

stake, place board on top of stake while ham-

mering.

NOTE: If ground is hard and stake is difcult to

install, make a crosscut in ground using a at

shovel.

Board

Stake

Soil

Ground

Package Contents

6”

2 1/2”

4 1/2”

2 1/4”

INSTALLATION INSTRUCTIONS

www.voltlighting.com

VOLT®The Tank

130 Series

Wire Connections

Strip two leads from luminaire pigtail. Using two wire connectors, sold

separately, connect leads from luminaire to main low voltage supply

cable lead.

Luminaire Wires

Main Low Voltage

Supply Cable

Wire

Connectors

Clear away area in ground at wireway

slot in top of stake. Lay luminaire

pigtail into wireway slots and screw

luminaire into stake.

If using optional stake cover, sold

separately, align the wireway slots on

stake cover and stake before screw-

ing luminaire into stake.

Use included locknut to secure the

luminaire position.

Install Luminaire to Stake

Luminaire

Stake Cover

Stake

Pigtail

Wireway Slot

customersupport@voltlighting.com • 813.978.3700

Install Shield to Luminaire

Install Lamp

Thread shield onto luminaire. Hand

tighten until snug. Adjust the luminaire

to desired angle by using adjustment set

screw.

Insert lamp, sold separately, with

correct wattage and type as marked on

luminaire label.

CAUTION: Do not exceed maximum watt-

age marked on luminaire label.

NOTE: DO NOT TOUCH halogen lamp

with bare hands. Use soft cloth to han-

dle lamp.

Shield

Luminaire

Socket

Lamp

Maintenance - Lamp Replacement

Unscrew shield to expose lamp then replace it with correct wattage and

type as marked on luminaire label. Reinstall shield to luminaire.

IMPORTANT: Halogen lamps must be protected from moisture and dust at all

times. Always reinstall shield when moved.

Set Screw

is-130-ver1.pdf

Specications and product details subject to change without notice.

[email protected] • 813.978.3700

www.voltlighting.com

Table of contents

Other Volt Landscape Lighting manuals

Popular Landscape Lighting manuals by other brands

Intex

Intex SL1006 owner's manual

LED Group

LED Group ROBUS R2IN13W quick start guide

Patriot Lighting

Patriot Lighting 343-1484 installation manual

Hess

Hess SERA G: SERA S Installation and operating instructions

LIGMAN

LIGMAN JET 44 installation manual

LIGMAN

LIGMAN MALTA 1 installation manual

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Specification sheet

Cooper Lighting

Cooper Lighting Invue 42 - 175W Specification sheet

Saxby Lighting

Saxby Lighting Islay 68784 Instruction leaflet

LIGMAN

LIGMAN EU-10016-3 installation manual

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza specification

LIGMAN

LIGMAN KI-60475 installation manual

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Malibu Boats

Malibu Boats CL905K instructions

LIGMAN

LIGMAN NYB-30161 installation manual

LIGMAN

LIGMAN SI-80021 installation manual

Malibu Boats

Malibu Boats CM110P instructions

U.S.T.E.

U.S.T.E. VISTA 8202 installation instructions