Vivotek MD7560X User manual

Quick Installation Guide

Network Camera

MD7560X

P/N: 625014800G Ver.1.0

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Contact your distributor in the event of

occurrence.

Refer to your user’s manual for

the operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

English

Software CD

MD7560X

Quick Installation Guide /

Warranty Card

Screwdriver

Alignment Sticker

Ground Wire / Screws

Package Contents

Silica Gel / RJ45 Female/Female

Coupler

Network Camera

Model No: MD7560X

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D107258A

Record the MAC address

before installing the camera.

Screw Holes

Physical Description

Inner View

Outer View

Lens

MicroSD/SDHC Card Slot

Reset Button

Status LED

Temperature Sensor

The event will be triggered

once the temparature inside the

Network Camera reaches 60°C.

Waterproof Level: IP67

English

First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your

MicroSD/SDHC Card if necessary.

Then, follow the steps below to install the camera to either the ceiling or the wall:

1. Attach the supplied alignment sticker to the ceiling/wall.

2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the

plastic anchors into the holes if necessary.

3. This Network Camera can be mounted with the cable routed through the ceiling/wall or from the

side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the

picture. If the cable goes through the side of the dome cover, please remove the rubber stopper

(B).

4. Through the 3 holes on the camera base, insert the screws to corresponding holes and secure

the camera base with a screwdriver.

Dome Cover

Hardware Installation

Tamper-proof Screw

Camera Base

Rubber Stopper

Ceiling Mount

Wall Mount

Installing the Ground Wire



hole, then route the other side of the ground wire to the ground.

Please secure the screws tightly to

avoid moisture.

English

Power over Ethernet (PoE) (MD7560X)

OWE

OLLIS

ION

LINK

IVE

TITION

12345

PoE Switch

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE

switch.

When using a PoE-enabled switch

This Network Camera is PoE-compliant, allowing transmission of power and data via a single

Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via

Ethernet cable.

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

PoE Power Injector

(optional)

Non-PoE Switch

If you have external DI devices, make the connection from general I/O terminal block.

Network Deployment

Network Camera

Model No: MD7560X

Made in Taiwan

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Pat. 6,930,709

RoHS

V I

MAC:0002D107258A

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is ana-

lyzed, please click on the “Next” button to continue the program.

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras

on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matches the one

labeled on the bottom of your device to connect to the Network Camera via Internet Explorer.

0002D107258A

00-02-D1-07-25-8A 192.168.5.151 MD7560X

Installation

Wizard 2

Assigning an IP Address

English

For further setup, please refer to the user's manual on the software CD.

2011/04/01 17:29:41

Ready to Use

1. Access the Network Camera on the LAN.

2. Retrieve live video through a web browser or recording software.

To adjust the viewing angle

Adjust the lens to a desired viewing angle as the diagram shown below.

90°

Adjusting the Lens

DO NOT over rotate the lens. Doing

so will damage the camera lens

module.

Attach the dome cover to camera.

Secure the dome screws with the

supplied screwdriver. Finally, make sure

all parts of the camera are securely

installed.

Completion

Fine-tune the Camera Focus



!

Tighten the lens lock screw.

1. Loosen the lens lock screw.

"#$

until the live image is clear.

3. Tighten the lens lock screw.

Please secure the screws tightly to

avoid moisture.

Tear down the aluminum foil vacuum bag and

take out the silica gel. Attach the supplied silica

gel to the inner side of the Network Camera.

(Please replace the silica gel with a new one if

you open the back cover after installation.)

This manual suits for next models

Table of contents

Other Vivotek Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide