Vivotek IZ7151 User manual
EN - 1
English
Contact your distributor when such
cases happen.
Keep the Network Camera away
from water. If the Network Camera
is wet, power off immediately.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera
as soon as it is found smoking or
smelt unusual.
Do not place the Network Camera
around the heat sources, such as
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera
in high humid environments.
Contact your distributor when such
cases happen.
Warning Before Install
EN - 2
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
when it's lightening.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert any object into the
Network Camera, such as needles.
EN - 3
English
Camera stand Screws and top mounting stand
IZ7151
Warranty card
Power adapter
Quick installation guide Software CD
1Check Package Contents
EN - 4
2Physical Description
Mic
RESET
Ethernet
Ext. Int. Audio
Out
12345678
Power cord socket
Ethernet 10/100
RJ45 socket
Indented reset button
General I/O
terminal block
Audio out
Microphone in
External/Internal
Microphone switch
Front panel
Back panel
Built-in Microphone
Status LED
EN - 5
English
3Hardware Installation
Mounting the camera
1. Attach the top mounting stand to the camera using the supplied screws.
2. Fasten the camera stand to the wall / ceiling.
3. Secure the camera to the camera stand.
4. Position the camera with the lens facing the desired monitoring area.
2
3
4
1
2
3
4
EN - 6
General Connection (without PoE)
1. Connect the camera to a switch via Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
12
Ethernet switch
4Network Deployment
EN - 7
English
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE switch
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the camera and a non-
PoE switch.
non-PoE switch
PoE power injector
(optional)
When using a PoE-enabled switch
The camera is PoE-compliant, allowing transmission of power and data via single
Ethernet cable. See the following illustration to connect the camera to a PoE-
enabled switch via Ethernet cable.
EN - 8
0002D1ABCD99
1. Install the "Installation Wizard 2" under the Software Utility directory from software
CD.
2. The program will conduct analyses on your network environment. After your
network is analyzed, please click on the "Next" button to continue the program.
3. The program will search the VIVOTEK Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that
matches the one labeled on the bottom of your device to connect the Internet
Explorer to the Network Camera.
0002D1ABCD99
Installation
Wizard 2
5Assigning IP Address
EN - 9
English
For further setup, please refer to user's manual on the software CD.
6Retrieving Images
Other manuals for IZ7151
2
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek FD7160 User manual
Vivotek
Vivotek FD8166 User manual
Vivotek
Vivotek CC8130 User manual
Vivotek
Vivotek SD8161 User manual
Vivotek
Vivotek IP8331 User manual
Vivotek
Vivotek FE9192-H User manual
Vivotek
Vivotek FE8172 User manual
Vivotek
Vivotek FD8155 User manual
Vivotek
Vivotek PT3113 User manual
Vivotek
Vivotek PZ6114 User manual
Vivotek
Vivotek IP7160 User manual
Vivotek
Vivotek FD7132 User manual
Vivotek
Vivotek FD8361L User manual
Vivotek
Vivotek IP9164-HT User manual
Vivotek
Vivotek CC8130 User manual
Vivotek
Vivotek SD7313 User manual
Vivotek
Vivotek IP8161 User manual
Vivotek
Vivotek FE8173 User manual
Vivotek
Vivotek FD8131 User manual
Vivotek
Vivotek PT1111 User manual
