Vivotek IP7251 User manual

P/N:625006300G Ver.1.0

Cover [IP7251]-Outline.ai 2008/6/27 上午 11:54:50

EN - 1

English

Contact your distributor when such

cases happen.

Keep the Network Camera away

from water. If the Network Camera

is wet, power off immediately.

Refer to your user's manual for the

operating temperature.

Power off the Network Camera

as soon as it is found smoking or

smelt unusual.

Do not place the Network Camera

around the heat sources, such as

television or oven.

Keep the Network Camera away

from direct sunlight.

Do not place the Network Camera

in high humid environments.

Contact your distributor when such

cases happen.

Warning Before Install

EN - 2

Do not place the Network Camera

on unsteady surfaces.

Do not touch the Network Camera

when it's lightening.

Do not disassemble the Network

Camera.

Do not drop the Network Camera.

Do not insert any object into the

Network Camera, such as needles.

EN - 3

English

Camera stand CS-mount lens

IP7251

Warranty card

Power adapter

Quick installation guide Software CD

1Package Contents

L-type hex key wrench /

C-mount ring (for C-mount lens)

EN - 4

Power cord socket

Ethernet 10/100

RJ45 socket

Indented reset button

General I/O

terminal block

Audio out

MIC in

External/Internal

MIC switch

Front panel

Back panel

Lens

Focus controller

Zoom controller

2Physical Description

Built-in MIC

Light sensor

Status LED

EN - 5

English

For further setup, please refer to the lens' instruction manual inside the

lens package.

1. Mount the lens by turning it clockwise onto the camera mount until it stops. If

necessary, turn the lens counterclockwise slowly until it gets the best attitude.

2. Connect the lens cable plug to the camera connector.

3Mounting the Lens to the Camera

General Connection (without PoE)

1. Connect the camera to a switch via Ethernet cable.

2. Connect the supplied power cable from the camera to a power outlet.

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

4Network Deployment

Ethernet switch

EN - 6

Power over Ethernet (PoE)

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the camera and a non-

PoE switch.

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

non-PoE switch

PoE power injector

(optional)

When using a PoE-enabled switch

The camera is PoE-compliant, allowing transmission of power and data via single

Ethernet cable. See the following illustration to connect the camera to a PoE-

enabled switch via Ethernet cable.

PoE switchP

wit

POWER COLLISION

LINK

RECEIVE

PARTITION

12345

EN - 7

English

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

RoHS

Network Camera

Model No: IP7251

Pat. 6,930,709 Made in Taiwan

Mac: 0002D106DB41

0002D106DB41

Installation

Wizard 2

5Assigning IP Address

1. Install the "Installation Wizard 2" under the Software Utility directory from software

CD.

2. The program will conduct analyses on your network environment. After your

network is analyzed, please click on the "Next" button to continue the program.

3. The program will search the VIVOTEK Video Receivers, Video Servers or Network

Cameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that

matches the one labeled on the bottom of your device to connect the Internet

Explorer to the Network Camera.

EN - 8

For further setup, please refer to user's manual on the software CD.

Network Camera

Ready to Use

1. Access to the Network Camera from the Internet.

2. Retrieve live video through web browsers or recording software.

3. Unscrew the zoom controller to adjust the

zoom factor. Upon completion, tighten the

zoom controller.

4. Unscrew the focus controller to adjust the

focus range. Upon completion, tighten the

focus controller. W

∞

EN - 9

English

Fine-tune the Camera Focus

1. Detach the CS-mount lens from the camera body.

2. Turn the camera body bottom up.

3. Use the supplied L-type hex key wrench to loosen the lens mounting screw; the

CS-mount ring becomes rotatable.

4. Use a coin to turn the CS-mount ring; ﬁne-tune the distance between the

sensor and the lens.

5. When ﬁnished, tighten the lens mounting screw to ﬁx the CS-mount ring.

6. Attach the CS-mount lens back to the camera body.

Lens mounting screw

CS-mount ring

Other manuals for IP7251

Table of contents

Other Vivotek Security Camera manuals

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide