Vivotek FD8135H User manual
Quick Installation Guide
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
720P HD • P-Iris • WDR Pro
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625016800G Rev. 1.0
FD8135H Fixed Dome
Network Camera
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Refer to your user's manual for the
operating temperature.
Keep the Network Camera away from
direct sunlight.
Do not place the Network Camera in
high humidity environments.
Contact your distributor in the event of
occurrence.
Warning Before Installation
EN - 2
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN - 3
English
Software CD
FD8135H Alignment Sticker
T10 Torx Screwdriver/ Screws /
Plastic Anchors / AV Cable
5
1
0
0
0
0
2
1
1
G
Package Contents
1
Quick Installation Guide /
Warranty Card
EN - 4
Physical Description
2
1 23 74 5 86
Ethernet
Micro SD Card
Audio InAV Out
Reset
Int. NTSC
PAL
Ext.
Camera Front View
Camera Rear View
Light Sensor
Lens
Built-in
Microphone
PIR Sensor
Black Cover
IR LEDs
(18 units, effective up to 15m)
Reserved
Focus Assist
Button
General IO Terminal
Block
1. AC24V_2
2. AC24V_1
3. DI 3+
4. DI 2+
5. DI 1+
6. DI- (GND)
7. DO-
8. DO+ (+12V)
Microphone In
(pink)
Audio/Video Out
(green)
Jumpers
Microphone Video Output
internal
external
NTSC
60Hz
PAL
50Hz
1 2
Reset Button
Micro SD/
SDHC Card
Slot
10/100BaseT
Ethernet
The max. output load from
pins #7 and 8 is 50mA.
NOTE:
EN - 5
English
Hardware Installation
3
Remove the black cover as shown below so that you can ne-tune the focus and zoom the
camera later when the cabling is done.
50
50
5m
41
41 5m
Before installing your camera,
make sure the built-in PIR (Passive
Infrared Sensor) can be directed
toward the area of interest, where
possible intrusion may occur. (The
sensitivity of PIR sensor depends
on the object size and temperature
differences between the object and
the background environment.)
Dome Cover Bottom of the
Camera
Tilt Ajustment
Screw
Focus Ctrl
Zoom Ctrl
Top View Side View
EN - 6
General Connection (without PoE)
Network Deployment
4
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
1. If you have external DI devices, make the connection from general I/O terminal block.
2. Ethernet, power, and other cables are user-supplied.
3. Connect the AC cables from the terminal block as an alternate power source. The IO
cables are user-supplied.
1. Attach the alignment sticker to the ceilling/wall.
2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall.
3. The Network Camera can be mounted with the cable routed through the ceiling/wall or
from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A
as shown in the above picture.
4. Hammer the supplied plastic anchors into the holes.
5. Align the two holes on each side of the camera base with the two plastic anchors on the
ceilling/wall, insert the supplied screws to corresponding holes and secure them with a
screwdriver.
Wall Mount
Ceiling Mount
Ethernet
Switch
Pin1 & 2 AC 24V
Pin #1 & 2 AC 24V as alternate power are for
indoor use only
NOTE:
EN - 7
English
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Power over Ethernet (PoE)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.
Non-PoE Switch
PoE Power Injector
(optional)
PoE Switch
1. This equipment is only to be connected to
PoE networks without routing to outside
plants.
2. For PoE input connections, use only UL
listed I.T.E. with PoE output.
NOTE:
EN - 8
0002D107258A
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
0002D107258A
00-02-D1-07-25-8A 192.168.5.151 FD8135H
Installation
Wizard 2
Assigning an IP Address
5
EN - 9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the 32-
channel recording software from the software CD in a deployment consisting of multiple
cameras. For its installation details, please refer to its related documents.
Other manuals for FD8135H
3
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek Supreme SD9363 User manual
Vivotek
Vivotek SC8131 User manual
Vivotek
Vivotek FD8166 User manual
Vivotek
Vivotek IB836BA-HT User manual
Vivotek
Vivotek Supreme MD8531H User manual
Vivotek
Vivotek IP8362 User manual
Vivotek
Vivotek FD8133 User manual
Vivotek
Vivotek IB8369A User manual
Vivotek
Vivotek FD6112V User manual
Vivotek
Vivotek FD8162 User manual
Vivotek
Vivotek IP7251 User manual
Vivotek
Vivotek FD8162 User manual
Vivotek
Vivotek IP7160 User manual
Vivotek
Vivotek FD8131 User manual
Vivotek
Vivotek IP8372 User manual
Vivotek
Vivotek FD9367-HTV User manual
Vivotek
Vivotek Supreme MD8563-EH User manual
Vivotek
Vivotek IB8367 User manual
Vivotek
Vivotek PZ7131 User manual
Vivotek
Vivotek IT9389 Series User manual
