Vivotek MD8562 User manual

MD8562/8562D

P/N:625015501G Ver1.1

2MP .Vandal-proof .Mobile Surveillance

EN - 1

English

Power off the Network Camera as

soon as smoke or unusual odors are

detected.

Contact your distributor in the event of

occurrence.

Refer to your user’s manual for

the operating temperature.

Warning Before Installation

Do not place the Network Camera on

unsteady surfaces.

Do not touch the Network Camera

during a lightning storm.

Do not drop the Network Camera.

Do not insert sharp or tiny objects

into the Network Camera.

EN - 2

Software CD

MD8562

Quick Installation Guide /

Warranty Card

Screwdriver

Alignment Sticker

Ground Wire / Screws

Package Contents

Moisture Absorber / RJ45 Female/

Female Coupler

(PoE) General I/O Terminal Block

(With power cord)

Ethernet 10/100 RJ45 Plug

Microphone In (pink)

Power Cord Socket (black)

MD8562D

EN - 3

English

IMPORTANT!

Record the MAC address before

installing the camera.

Screw Holes

Physical Description

Inner View

Outer View

Lens

MicroSD/SDHC

Card Slot

Waterproof Level: IP67

Reset button

Status LED

EN - 4

First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your

MicroSD/SDHC Card if necessary.

Then, follow the steps below to install the camera to either a ceiling or wall:

1. Attach the supplied alignment sticker to the ceiling/wall.

2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the

plastic anchors into the holes if necessary.

3. This Network Camera can be mounted with the cable routed through the ceiling/wall or from the

side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in the

picture. If the cable goes through the rear opening of the dome cover, please remove the plastic

cover (B).

4. Through the 3 holes on the camera base, insert the screws to corresponding holes and secure

the camera base with a screwdriver.

Dome Cover

Hardware Installation

Tamper-proof Screw

Camera Base

Plastic Cover

Ceiling Mount

EN - 5

English

Wall Mount

Installing the Ground Wire

As shown in the gure below, secure one side of the supplied ground wire to the screw hole, route

the wire, and attach the other end to a junction box or a grounded conduit.

IMPORTANT!

Please secure the screws tightly

to avoid moisture.

EN - 6

General Connection (without PoE) (MD8562D)

Network Deployment

+ : Digital input

- : Digital input

POWER C

OLLIS

ION

LINK

CEIVE

PARTITION

12345

Ethernet Switch

1. If you have external DI devices, make the connection from general I/O terminal block.

2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch.

Use a Category 5 Cross Cable when Network Camera is directly connected to PC.

3. Connect the power cable from the Network Camera to a power outlet.

EN - 7

English

Power over Ethernet (PoE) (MD8562)

POWER C

OLLIS

ION

LINK

CEIVE

PARTITION

12345

PoE Switch

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE

switch.

When using a PoE-enabled switch

This Network Camera is PoE-compliant, allowing transmission of power and data via a single

Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via

Ethernet cable.

POWER C

OLLIS

ION

LINK

RECEIVE

PARTITION

12345

PoE Power Injector

(optional)

Non-PoE Switch

NOTE:

1. This equipment is only to be connected to PoE networks

without routing to outside plants.

2. For PoE input connection, use only UL listed I.T.E. with

PoE output.

3. The DC power adaptor, if used, should comply with:

O/P: 12Vdc, 1.5A min., L.P.S. certied.

EN - 8

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is ana-

lyzed, please click on the “Next” button to continue the program.

0002D108323

00-02-D1-10-83-23 192.168.5.151 MD8562

Installation

Wizard 2

Assigning an IP Address

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras

on the same LAN.

4. After a brief search, the main installer window will pop up. Double-click on the MAC address

that matches the one printed on the camera label or the serial number on the package box

label to open a browser management session with the Network Camera.

EN - 9

English

For further setup, please refer to the user's manual on the software CD.

Ready to Use

To adjust the viewing angle

90°

Adjusting the Lens

Loosen the screws (not removing

them) on the sides of lens module.

Adjust the lens to a desired viewing

angle as shown on the right.

When done, fasten the screws so that

lens orientation can be xed

and withstand shock and

vibration.

1. A browser session with the Network Camera should prompt as shown below.

2. You should be able to see live video from your camera. You may also install the 32-channel

recording software from the software CD in a deployment consisting of multiple cameras.

For its installation details, please refer to its related documents.

Other manuals for MD8562

This manual suits for next models

Table of contents

Other Vivotek Security Camera manuals

Vivotek

Vivotek FD8371EV User manual

Vivotek

Vivotek IP6112 User manual

Vivotek

Vivotek IP8173H User manual

Vivotek

Vivotek SD83x1E User manual

Vivotek

Vivotek IT9360-H User manual

Vivotek

Vivotek IP8371E User manual

Vivotek

Vivotek FD8335H User manual

Vivotek

Vivotek FD7141 User manual

Vivotek

Vivotek SUPREME IP9165-HP User manual

Vivotek

Vivotek Supreme IP8151 User manual

Vivotek

Vivotek IP7160 User manual

Vivotek

Vivotek FE8174V User manual

Vivotek

Vivotek Supreme MD8563-EH User manual

Vivotek

Vivotek Supreme SD9363 User manual

Vivotek

Vivotek FD8335H User manual

Vivotek

Vivotek IP8132 User manual

Vivotek

Vivotek PD8136 User manual

Vivotek

Vivotek FD8335H User manual

Vivotek

Vivotek FE9382-EHV-v2 User manual

Vivotek

Vivotek IP8160-W User manual

Vivotek

Vivotek IB9387-LPR User manual

Vivotek

Vivotek FD8377-HTV User manual

Vivotek

Vivotek FD8152V User manual

Vivotek

Vivotek FE9380-HV User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide