Vivo STAND-V032T User manual

Dual Monitor Extra Tall Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v032t

SKU: STAND-V032T

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Lower Pole

F (x2)

VESA Plate

S-A (x3)

M6x16mm

Screw

T-A (x1)

3mm Allen

Wrench

T-B (x1)

5mm Allen

Wrench

T-C (x1)

6mm Allen

Wrench

S-B (x2)

M6 Security

Nut

M-A (x8)

M4x12mm

Thumb Screw

M-B (x8)

M4x30mm

Screw

M-C (x8)

M6 Spacer

G (x1)

Pole Cap

H (x3)

Pole Cable

Clip

I (x4)

Cable Clip

J (x1)

Grommet

Plate

K (x1)

So Pad

L (x1)

Support Plate

B (x1)

Middle Pole

C (x1)

Upper Pole D(x1)

Clamp

E(x1)

Mount Arms

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

ASSEMBLY STEPS

TOOLS NEEDED

Phillips

Screwdriver

22 lbs

Per Arm

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

STEP 1

STEP 2: Option A - Desk Clamp

Loosen knob on Clamp (D), as shown below.

Connect Clamp (D) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A).

Place assembly on desktop and secure by tightening knob on Clamp (D).

T-A

S-A

Lower Pole (A) & Upper Pole (C) may look similar.

To dierentiate, match the hole pattern to images below:

Lower Pole Upper Pole

(A) (C)

STEP 2: Option B - Grommet

Using a phillips screwdriver, remove the screw from Clamp (D) and disassemble. Set Knob (D1)

aside. Connect Grommet Plate (J) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen

Wrench (T-A). Remove adhesive backing from So Pad (K) and adhere to Grommet Plate (J).

Place the pole assembly over grommet hole in desk, and connect using Support Plate (L) and

previously removed Knob (D1) from underneath desk, as shown. Secure by tightening Hand Bolt

(D1). For desktops without an existing gromment hole, use a 3/8” (10mm) drill bit to drill through

desktop, then secure assembly as previously described.

EXISTING

GROMMET HOLE

DRILLING A

GROMMET HOLE

Lower Pole (A) & Upper Pole (C) may look similar.

To dierentiate, match the hole pattern to images below:

Lower Pole Upper Pole

(A) (C)

S-A

T-A

STEP 3

Tighten and secure Middle Pole (B) to Lower Pole (A), then connect Upper Pole (C) to Middle Pole (B).

STEP 4

Slide Pole Cable Clips (H) over pole assembly, then attach Mount Arms (E) and secure using 6mm

Allen Wrench (T-C). Press Pole Cap (G) into pole assembly.

Attach Cable Clips (I) to Monitor Arms (E) by snapping into place.

T-C

STEP 5

Secure VESA Plates (F) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B).

M6 Spacers (M-C) may be required.

Slide monitors with VESA Plates (F) onto Mount Arms (E). Secure VESA Plates (F) in place using

M6 Security Nuts (S-B).

Route cables through Cable Clips (I) and Pole Cable Clips (H).

M-A

M-B

M-C

STEP 6

S-B

STEP 7

Adjust the monitor tilt using 5mm Allen Wrench (T-B). To level monitors, remove M6 Security Nuts

(S-B) and tighten or loosen adjustment screws using 3mm Allen Wrench (T-A). Once level, fasten M6

Security Nuts (S-B) back into place.

T-B

S-B

T-A

LAST UPDATED: 11/14/2022

REV1.1

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular TV Mount manuals by other brands

Ergotron

Ergotron Neo Flex Cantilever UHD user guide

StarTech.com

StarTech.com FPCEILBTB user manual

VonHaus

VonHaus 05/038 instruction manual

Techlink

Techlink ECHO TV manual

Sandstrom

Sandstrom SSTVMC12X instruction manual

Sony

Sony SU-WL700 Additional information for Using

ICW

ICW SCACC18 installation instructions

LG WM-L640V owner's manual

Gembird

Gembird WM-65ST-01 user manual

ERARD

ERARD FiTUP XXL 035320 quick start guide

PEERLESS

PEERLESS PLCK-1 Installation and assembly

Kanto

Kanto RCF180 user manual

GEM

GEM GEM GP001 instructions

Gladiator Joe

Gladiator Joe GJ0A0053 quick start guide

Vivotek

Vivotek AM-105 installation guide

AmazonBasics

AmazonBasics B07QG3LMG4 manual

Secura

Secura QLF210 instruction manual

Marquant

Marquant 929-083 Operating instructions in original