Vivo STAND-V006 User manual

Hex Monitor Desk Mount

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v006

SKU: STAND-V006

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

a (x1)

Pole

b1 (x1)

Clamp

b2 (x1)

Clamp

Brace

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED

c(x1)

Decorative

Cover

d1 (x2)

Monitor Arm

d2 (x4)

Monitor Arm

e (x8)

Monitor Arm

Cover

f (x8)

Plastic Pad

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

g (x4)

M10x47

h(x3)

Clamp Brace Bolt

i(x2)

M10x15

j (x4)

M8x10

k (x1)

M10 Bolt

l (x1)

Support Plate

m(x1)

M10 Washer

o(x1)

Eva Pad

p (x24)

M4x12 Thumb Screw

r (x24)

M4 Spacer

s (x2)

Spare Cap

t(x1)

Allen Wrench

Set

u(x1)

Wrench

v1 (x4)

VESA Plate

v2 (x2)

VESA Plate

w1 (x4)

Nut

w2 (x2)

M4x6

x(x8)

Wire Clip

n(x1)

Spring Washer

q (x24)

M4x30

ASSEMBLY STEPS

TOOLS NEEDED

Phillips

Screwdriver

STEP 1

22lbs

(10kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

Figure 1 Figure 2

b1 eye bolt

Figure 3 Figure 4

OPTION A: Weighted Base Installation

Attach clamp brace (b2) to pole (a) with clamp brace bolts (h). Attach clamp (b1) to clamp brace at

desired height using M10x15 bolts (i) with Allen wrench (t). Tighten clamp to desk and slide decorative

cover (c) into place.

OPTION B: Existing Grommet Base Installation

Apply foam pad (o) to base of pole (a). Mount pole to grommet hole in desk using M10 bolt (k), spring

washer (n), M10 washer (m) and support plate (l). Tighten with wrench (u) and slide decorative cover

STEP 2

STEP 1 (Continued)

Figure 5 Figure 6

2.1

2.2

2.3

Step 4B

OPTION C: Self-Drilled Grommet Base Installation

Drill a 3/8” (10mm) diameter hole at desired location. Apply foam pad (o) to base of pole (a). Mount

pole to grommet hole in desk using M10 bolt (k), spring washer (n), M10 washer (m) and support

plate (l). Tighten with wrench (u) and slide decorative cover (c) into place.

Place plastic pads (f) onto ends of monitor arms (d2), insert into arms (d1), and secure using M10x47

bolts (g) with Allen wrench (t). Press monitor arm covers (e) onto joints.

STEP 3

d1,d2

STEP 4

Install wire clips (x) on arms (d1,d2). Install arms on pole (a) at

desired height using M8x10 bolts (j) with Allen wrench (t), making sure

wire clips are facing down.

4A: Side VESA Plates

For monitors with flat back attach VESA plates (v1) with thumb screws (p). For monitors with curved

back attach VESA plates (v1) with screws (q) and spacers (r). Screws need only to be finger-tight.

4B: Center VESA Plates

For monitors with flat back attach VESA plates (v2) with thumb screws (p). For monitors with curved

back attach VESA plates (v2) with screws (q) and spacers (r). Screws need only to be finger-tight.

STEP 5

STEP 6

d1,d2

grub

screw

Fix the tilt angle

5B: Center VESA Plates

Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with screw (w2). Slide top

monitor onto mount in same fashion.

5A: Side VESA Plates

Slide monitor onto the head of arm (d2) as shown in the diagram. Secure with nut (w1).

Remove plastic cover and use wrench (u) to tighten the nut if the tilt angle cannot be fixed. Fasten the

grub screws on the center monitors to fix the tilt angle using Allen wrench (t).

STEP 8

STEP 7

STEP 9

Adjust the height of Center Monitors: Turn the bolt counter-clockwise to lower the center monitors.

Turn the bolt clockwise to raise the center monitors. Use allen wrench (t). Adjust the height of the

Side Monitors: Remove nut (w1) and turn the bolt counter-clockwise to raise the monitor. Use allen

wrench (t).

To adjust swivel joint tension, remove the monitor arm cover (e) and turn the bolt underneath with

the Allen wrench(t).

Use wire clips (x) to help manage wires.

LAST UPDATED: 07/09/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 