Vivo MOUNT-KB35B User manual

Black Pneumatic Wall Mounted Keyboard Tray

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/mount-kb35b

SKU: MOUNT-KB35B

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please contact our product support team at 309-278-5303 or [email protected]

for further assistance. Check carefully to make sure there are no missing or defective parts.

Improper installation may cause damage or serious injury. Do not use this product for any

purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We

cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

13.2lbs

(6kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

A (x1)

Wall Plate

S-A (x8)

M5x10mm Screw

S-B (x4)

M4x6mm Screw

NOTE: SOME HARDWARE MAY NOT BE USED

Drill Pencil

Stud Finder Phillips

Screwdriver

B (x1)

Arm Extension

C (x1)

Arm

D (x1)

Keyboard Bracket

E (x1)

Keyboard Tray Set

F (x1)

Handle

S-C (x2)

M6x16mm Screw

S-D (x2)

M6x25mm Spring

Screw

M-A (x3)

M6x50mm Screw

M-B (x3)

Concrete Anchor

S-E (x1)

M6 Washer

S-F (x2)

M4 Washer

G (x1)

Wall Plate Cover

H (x2)

Cap

I (x5)

Velcro Pad

T-A (x1)

3mm Allen Wrench

T-B (x1)

4mm Allen Wrench

T-C (x1)

5mm Allen Wrench T-D (x1)

Level

TOOLS NEEDED

J (x1)

Connecting Plate

ASSEMBLY STEPS

STEP 1

OPTION A: Wood Stud Installation

Place Wall Plate (A) against the wall and mark drilling locations with a pencil. Use of a stud

finder and Level (T-D) is highly recommended. Drill 1.2” (30mm) deep holes using a .12”

(3mm) bit, then attach Wall Plate (A) to wall using M6x50mm Screws (M-A) and a Phillips

screwdriver. Assemble Wall Plate Covers (H) to Wall Plate (A).

OPTION B: Concrete/Brick

Place Wall Plate (A) against the wall and mark drilling locations with a pencil. Use of a

Level (T-D) is highly recommended. Drill 2” (50mm) deep holes using a .31” (8mm) bit,

press Concrete Anchors (M-B) into holes, then attach Wall Plate (A) to wall using M6x50mm

Screws (M-A) and a Phillips screwdriver. Assemble Wall Plate Covers (G) to Wall Plate (A).

3mm

30mm(1.2 )

(0.12 )

8mm

50mm(2.0 )

(0.31 )

T-D

M-A

T-D

M-B

STEP 2

Slide Arm Extension (B) onto Wall Plate (A). Secure using M6x25mm Spring Screw (S-D)

and Cap (H) with a Phillips screwdriver.

Place Arm (C) onto Arm Extension (B). Secure using M6x25mm Spring Screw (S-D),

Cap (H), and a Phillips screwdriver.

S-D

STEP 3

The Keyboard Bracket (D) features a tilt adjustment allowing you to use the full tilt range

or limit the range, with a Tilt Screw (D1) under the bracket. Take note of the two positions

below and then use 3mm Allen Wrench (T-A) to adjust the Tilt Screw (D1) so that it’s in the

limited range setting. This will aide in installing the Keyboard Tray in the next step.

T-A

Full Tilt Range Limited Tilt Range

Tilt Screw is fully recessed Tilt Screw is protruding

STEP 4

Assemble Keyboard Tray Set (E) to Keyboard Bracket (D) and Connecting Plate (J) using

M5x10mm Screws (S-A) and a Phillips Screwdriver.

STEP 5

Attach Handle (F) to Keyboard Tray Set (E) using M4x6mm Screws (S-B) and a Phillips

screwdriver.

S-A

NOTE: Ensure the lip on Keyboard Tray Set (E) is facing up in the back and the

handle mounting holes are in the front. Also ensure that the lips on Connecting

Plate (J) are facing downward.

STEP 6

Attach Keyboard Bracket (D) to Arm (C) using M6x16mm Screws (S-C), M6 Washer (S-E),

and 4mm Allen Wrench (T-B).

STEP 7

Attach the Lever (C1) from Arm (C) to Keyboard Tray (E) using M4x6mm Screws (S-B), M4

Washers (S-F), and a Phillips screwdriver.

T-B

S-C

S-E

S-B

S-F

STEP 8

To set the tilt range, adjust the Tilt Screw (D1) on Keyboard Bracket (D) using 3mm

Allen Wrench (T-A). When the Screw is protruding out, the keyboard tray has a limited

range of tilt. The tray has full range of motion when the Screw is fully recessed into the

Bracket.

Full Tilt Range

Tilt Screw is fully recessed

Limited Tilt Range

D1 T-A

Tilt Screw is protruding

STEP 9

Use 3mm Allen Wrench (T-A) to adjust the arm swivel points. Press and hold the Lever (C1)

to adjust the height of the keyboard. Remove protective film from Velcro Pads (I) and apply

to top of Keyboard Tray (E) to keep keyboard from slipping.

T-A

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 