Vicon V960D-W Series Instruction manual
Quick User Guide V960D-W Series Network Camera
Warning before installation
-Power off the Network camera if it is found to be smoking or smells unusual.
-Keep the Network camera away from water. If the Network camera gets wet, power
off immediately.
-Do not place the Network camera near heat sources, such as a television or oven.
-Refer to your instruction manual for the operating temperature.
-Keep the Network camera away from direct sunlight.
-Do not place the Network camera in high humidity environments.
-Do not place the Network camera on unsteady surfaces.
-Do not touch the Network camera when there is lightning present.
-Do not disassemble the Network camera.
-Do not drop the Network camera.
-Do not insert any object into the Network camera, such as a screwdriver.
For other safety and regulation information, please refer to “User’s manual”.
1. Check Contents
No.
Item
Description
1
Network Camera
V960D-W Series (V960D-WN312, V960D-WN312M,
V960D-WN920M, V961D-WN312, V961D-WN312M,
V961D-WN920M, V962D-WN312, V962D-WN312M,
V962D-WN920M,)
2
Software CD
User’s Manual, Utility software
3
Quick User Guide
This document
4
Accessories
Bottom Cushion Plate
Both-sided Tape
Silica-Gel
Anchor : 4pcs
O-ring : 4pcs
Tapping Screw 4x30 : 4pcs
Hexalobular L-key Wrench
Alarm I/O extension cable
Video monitor cable
2. Physical Description
Alarm In / Out connector
1. Network (RJ-45 PoE supported)
2. Audio In (Line in)
3. Audio Out (Line Out)
4. Alarm In / Out connector (Dry contact / Relay out [2A:AC120V/DC60V])
5. Power (DC12V / AC24V)
1
Quick User Guide V960D-W Series Network Camera
6. Micro SD card (SDHC supported)
7. Reset Button
8. Status LED
9. Video output for service monitor
3. Making Connection
Note: A mating connector for power is not supplied, but one can be purchased; it has an outer
diameter of 5 mm and an inner diameter of 2 mm. As an alternative, the connector can be
removed and the two wires attached directly; there is no polarity, so either wire can be used for
+ and the other for GND, regardless of color.
1. If you have external devices such
as sensor or alarms, make connection
from connectors
2. Connect Ethernet cable to make
connection to the network hub.
3. Connect power cable to the camera.
When you use PoE function, you don’t
need to connect power.
2
Quick User Guide V960D-W Series Network Camera
3
Quick User Guide V960D-W Series Network Camera
4. Assign IP address
Default setting is set to “DHCP” and “UPnP” function is set to ON. If your network
has a DHCP server and the UPnP function is enabled on your PC, you can find the
camera in “My Network”. Refer to the Multi Upgrade Tool manual for detailed
instructions.
Execute the Multi Upgrade Tool (from the Installation CD); it will search cameras on
the network automatically.
1) After the list of detected devices appears, select the camera you are trying to
configure.
2) Select the Network type as Static or DHCP. If Static is selected, enter all of the
network information for your camera.
3) Select the “Change IP Address” button. The message “Do you want to change IP
address?” will display; select “Yes” from the pop-up window.
4) Check the Type as Static or DHCP from the list.
Then double click the camera in the list; Internet Explorer® will open
automatically.
4
Quick User Guide V960D-W Series Network Camera
5. Web Browser Connection
Note : The Network camera supports Internet Explorer® 7 or above.
Please check version of your browser and update it if necessary.
When you first access the camera you need to download and install an
Active X control from the camera to display a Live image.
Default User and Password are set to “ADMIN” and “1234”. Please type in
the user ID and password to connect the network camera.
Note: By Default the cameras come with “Installation Mode” set to “ON” to
enable Analog output. Additionally, all installation setup must be done prior to
the camera being used with a VMS, including ViconNet; the VMS forces the
Installation Mode to OFF. You must turn installation mode off to use 720p or
1080p streaming.
For further information for setup, refer to User’s manual on the software CD.
5
Other manuals for V960D-W Series
1
This manual suits for next models
9
Table of contents
Other Vicon Security Camera manuals
Vicon
Vicon SN680D-A-WNIR User manual
Vicon
Vicon VC-700 User manual
Vicon
Vicon XX152-10-01 Installation instructions
Vicon
Vicon V905-CUBE User manual
Vicon
Vicon ROUGHNECK V910 User manual
Vicon
Vicon G-Cam/EFD-3266 User manual
Vicon
Vicon V672-PTZ User manual
Vicon
Vicon Cruiser SN663V-A Operating instructions
Vicon
Vicon CE202D-WN User manual
Vicon
Vicon Cruiser SN663V User manual
Vicon
Vicon ROUGHNECK V-CELL-HD-B User manual
Vicon
Vicon V980D Series User manual
Vicon
Vicon SVFT-MSH23C User manual
Vicon
Vicon VN-755IPV5 User manual
Vicon
Vicon Roughneck V920D Series User manual
Vicon
Vicon V810B User manual
Vicon
Vicon V661D-312IR Operating instructions
Vicon
Vicon XX235-01-01 Operating instructions
Vicon
Vicon SurveyorVFT User manual
Vicon
Vicon VC-630 User manual
