VADDIO CLEARVIEW HD-18 User manual

Partner: Vaddio

Model: ClearVIEW HD-18

Device Type: Camera

GENERAL INFORMATION

SIMPLWINDOWS NAME: Vaddio ClearVIEW HD-18 Camera Control v1.0

CATEGORY: Camera

VERSION: v1.0

SUMMARY: This module will control the Vaddio ClearVIEW HD-18 via RS232.

GENERAL NOTES:

This module provides control, real-time feedback from camera, and will also set

various advanced settings. It can have up to 16 presets. Press and hold preset x

input for 2 seconds and the position of camera will save onto that preset number.

There is also a reset mode that when toggled on will erase any preset number when

pressed afterwards.

If multiple units are daisy-chained then it will be necessary to pulse the

Set_Addresses input. This will set the address of each camera.

CRESTRON HARDWARE REQUIRED: C2I-COM, ST-COM, C2-COM-*

SETUP OF CRESTRON HARDWARE:

RS232

Baud:9600

Parity: None

Data Bits: 8

Stop Bits: 1

VENDOR FIRMWARE: Unknown

VENDOR SETUP: DIP switch 4 should be up for the baud rate of 9600.

CABLE DIAGRAM: A DB-9 to RJ-45 adapter is supplied with the camera for RS-232.

CONTROL:

Send_Address_Set D Pulse to set the addresses of the camera.

Power_<On/Off> D Pulse to turn the camera on or off.

Pan_Tilt_* D Press and hold to pan and tilt the camera.

Tilt_Speed A Analog signal to allow the tilt speed to be adjusted. Valid range is 0d to 14d.

Tilt_Speed_<Up/Down> D Pulse to adjust the tilt speed.

Tilt_Speed_Default D Pulse to set the tilt speed to the default value of 7d.

Partner: Vaddio

Model: ClearVIEW HD-18

Device Type: Camera

Pan_Speed A Analog signal to allow the pan speed to be adjusted. Valid range is 0d to 18d.

Pan_Speed_<Up/Down> D Pulse to adjust the pan speed.

Pan_Speed_Default D Pulse to set the pan speed to the default value of 9d.

Zoom_Speed A Analog signal to allow the zoom speed to be adjusted. Valid range is 0d to 7d.

Zoom_<In/Out> D Press and hold to zoom in or out.

Zoom_Speed_<Up/Down> D Pulse to adjust the zoom speed.

Zoom_Speed_Default D Pulse to set the zoom speed to the default value of 4d.

Focus_Speed A Analog signal to allow the focus speed to be adjusted. Valid range is 0d to 7d.

Auto_Focus_<On/Off/Toggle> D Pulse to turn the auto focus on and off.

Focus_<Near/Far> D Press and hold to adjust the focus.

Focus_Speed_<Up/Down> D Pulse to adjust the focus speed.

Focus_Speed_Default D Pulse to set the focus speed to the default value of 4d.

Preset_<1…16> D Pules to recall the preset. Press and hold for 2 seconds to store the current camera

position in the desired preset.

Reset_Mode D Pulse to put the module into preset reset mode. When the Reset_Mode_Is_On

output is high, pulsing a Preset_* input will clear the stored values for that preset.

Auto_White_Balance_<On/Off> D Pulse to turn the auto white balance on and off.

Backlight_<On/Off> D Pulse to turn the backlight on and off.

IR_Recieve_<On/Off/Toggle> D Pulse to turn the IR receiver on and off.

Tally_Light_<On/Off> D Pulse to turn the tally light on and off.

ICR_Cut_Filter_<On/Off> D Pulse to turn the ICR cut filter on and off.

Auto_Exposure_*_Mode D Pulse to set the desired auto exposure mode.

Shutter_<Up/Down> D Pulse to adjust the shutter. Auto Exposure mode must be set to either manual or

shutter priority.

Shutter_Reset D Pulse to set the shutter back to the default setting. Auto Exposure mode must be

set to either manual or shutter priority.

Partner: Vaddio

Model: ClearVIEW HD-18

Device Type: Camera

Aperture_<Up/Down> D Pulse to adjust the aperture.

Aperture_Reset D Pulse to set the aperture back to the default setting.

Gain_<Up/Down> D Pulse to adjust the gain.

Gain_Reset D Pulse to set the gain back to the default setting.

Red_Gain_<Up/Down> D Pulse to adjust the red gain.

Red_Gain_Reset D Pulse to set the red gain back to the default setting.

Blue_Gain_<Up/Down> D Pulse to adjust the blue gain.

Blue_Gain_Reset D Pulse to set the blue gain back to the default setting.

Iris_<Up/Down> D Pulse to adjust the iris.

Iris_Reset D Pulse to set the iris back to the default setting.

Exposure_Compensation_<On/Off> D Pulse to turn exposure compensation on and off.

Exposure_Compensation_<Up/Down> D Pulse to adjust the exposure compensation.

Exposure_Compensation_Reset D Pulse to set the exposure compensation back to the default setting.

IR_Receive_Return_Enable D Pulse to enable. Will send replies what command received from IR commander.

From_Device S Serial data signal to be routed from a 2 way com port.

FEEDBACK:

Power_Is_<On/Off> D High to indicate the current power state.

<Tilt/Pan/Zoom/Focus>_Speed_Gauge A

Analog value indicating the current tilt/pan/zoom/focus speed. To be displayed on a

gauge on a touch panel.

Auto_Focus_Is_<On/Off> D High to indicate the current auto focus state.

Reset_Mode_Is_On D High to indicate that the reset mode is on. Pulsing one of the Preset_<1…16>

while

this is high will reset the values stored for that preset.

Preset_Saved D Will pulse high for two seconds to indicate that the current camera position has

been stored.

Auto_White_Balance_Is_<On/Off> D High to indicate the current auto white balance state.

Partner: Vaddio

Model: ClearVIEW HD-18

Device Type: Camera

Backlight_Is_<On/Off> D High to indicate the current backlight state.

IR_Receive_Is_<On/Off> D High to indicate the current IR receive state.

Tally_Light_Is_<On/Off> D High to indicate the current tally light state.

ICR_Cut_Filter_Is_<On/Off> D High to indicate the current state of the ICR cut filter.

Auto_Exposure_Mode_Is_* D High to indicate the current auto exposure mode.

Exposure_Compensation_Is_<On/Off> D High to indicate the current exposure compensation state.

Error D High to indicate an error was received from the camera.

To_Device S Serial data signal to be routed to a 2 way com port.

TESTING:

OPS USED FOR TESTING: v4.003.0015

SIMPL WINDOWS USED FOR TESTING: 3.01.37

DEVICE DB USED FOR TESTING: 34.00.012.00

CRES DB USED FOR TESTING: 26.00.008.00

SYMBOL LIBRARY USED FOR TESTING: 724

SAMPLE PROGRAM: Vaddio ClearVIEW HD-18 Camera Control v1.0 Demo

REVISION HISTORY: v1.0 – Initial Release

Other manuals for CLEARVIEW HD-18

Other VADDIO Security Camera manuals

VADDIO

VADDIO WallVIEW CCU HD-19 User manual

VADDIO

VADDIO WallVIEW 70 PTZ Installation and operation manual

VADDIO

VADDIO BU-45H User manual

VADDIO

VADDIO VADDIO/CANON BU Series User manual

VADDIO

VADDIO ClearVIEW 999-6990-000 User manual

VADDIO

VADDIO RoboSHOT 12 User manual

VADDIO

VADDIO WALLVIEW HD-19 User manual

VADDIO

VADDIO RoboSHOT 20 UHD User manual

VADDIO

VADDIO RoboSHOT USB Series User manual

VADDIO

VADDIO RoboSHOT USB Series User manual

VADDIO

VADDIO CEILINGVIEW HD HIDEAWAY User manual

VADDIO

VADDIO 999-6925-000 User manual

VADDIO

VADDIO PTZCam 100 User manual

VADDIO

VADDIO RoboSHOT 12E HDBT User manual

VADDIO

VADDIO RoboSHOT HDBT Series User manual

VADDIO

VADDIO CeilingVIEW 70 PTZ HideAway User manual

VADDIO

VADDIO ZoomSHOT 20 QSR User manual

VADDIO

VADDIO RoboSHOT 12E USB User manual

VADDIO

VADDIO CLEARVIEW HD-20 User manual

VADDIO

VADDIO WallVIEW D80 PTZ User manual

VADDIO

VADDIO RoboSHOT HD-SDI Series User manual

VADDIO

VADDIO RoboSHOT 12 HD-SDI User manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 User manual

VADDIO

VADDIO Wallview CCU HD-20 HD-SD User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide