Tucker Barbecues GTR Series Assembly instructions
V07.01.20
ASSEMBLY, INSTALLATION
AND OPERATING INSTRUCTIONS
BUILT-IN BARBECUE
FOR GTR SERIES
MODELS:
GTR3, GTR4, GTR5, GTR6.
GTR3 S, GTR4 S, GTR5 S, GTR6 S.
GTR3 SS, GTR4 SS, GTR5 SS, GTR6 SS.
IMPORTANT – PLEASE READ ALL INSTRUCTIONS
BEFORE YOU ASSEMBLE, INSTALL OR
OPERATE THIS APPLIANCE.
2
GENERAL WARNINGS
BARBECUE ASSEMBLY INSTRUCTIONS
INSTALLATION INSTRUCTIONS & WARNINGS
SPECIFICATIONS
DIMENSIONS
GAS INSTALLATION AND LEAK TEST PROCEDURE
OPERATING INSTRUCTIONS
COOKING HINTS
TROUBLESHOOTING
SERVICE & MAINTENANCE
WARRANTY
3
4
9
11
12
15
18
19
20
22
23
CONTENTS
3
IMPORTANT SAFETY
INSTRUCTIONS
• Tucker GTR Barbecues are approved for
outdoor use only.
• Remove all plastic protection lm from
stainless steel components before assembly.
• Keep this manual for future reference.
• Read all instructions carefully before
assembly and usage of barbecue.
• Clean your barbecue regularly; check the
grease trays for excess grease build up as
damage by grease or fat re is not covered
by warranty.
• Always turn off the gas supply when you
nish barbecuing.
• A canvas cover for this barbecue will extend
its life and ensure trouble free operation.
• For installation of this barbecue onto its
cabinet refer to relevant instructions.
• Attend an operating barbecue at all times.
• Do not use this appliance indoors or in any
enclosed area.
• Do not spray aerosols in the vicinity of this
appliance while it is in operation.
• Do not place articles on or against this
appliance.
WARNING FOR
YOUR SAFETY
If you smell gas:
1. Shut off gas supply to appliance.
2. Extinguish any open ame.
3. Open lid or hood.
4. If odour continues, immediately call your
gas supplier or your Fire Department.
• Read all instructions carefully before
assembly and usage of the barbecue.
• Do not use or store ammable materials in or
near this appliance.
• Always leak test /check hose connections
after lling cylinders.
• Check cylinder condition for rust and that
the date stamp is current as every gas
cylinder in Australia must be pressure tested
every ten years.
• Never disconnect the barbecue whilst it is
running.
• Do not modify this appliance in any way.
• Do not allow children to operate the
barbecue.
• If a grease/fat re should arise, turn off the
gas supply immediately until extinguished.
• Always open the Lid or Roasting Hood before
lighting.
HAZARDOUS FIRE OR EXPLOSION MAY
RESULT IF INSTRUCTIONS ARE IGNORED.
It is the consumer’s responsibility to see that the
barbecue is properly assembled, installed and
taken care of. Failure to follow the instructions in
this manual could result in serious bodily injury
and /or property damage.
4
BARBECUE ASSEMBLY
INSTRUCTIONS
• Remove the pallet and any plastic lm protecting
or covering any parts of the Barbecue and
Cabinet Trolley before assembly.
• Cut away any packaging or cable ties that may
be holding components in place.
• Check you have all the correct components as
listed below.
10mm spanner
Phillips head screwdriver
TOOLS REQUIRED FOR ASSEMBLY
*Check that you have the correct gas type Barbecue i.e. L.P.GAS (red sticker) NAT
GAS (black sticker). The Gas Type Label is located on the right hand side of the
Barbecue Body.
BARBECUE PARTS
1x GTR Barbecue Body
1x Barbecue Fascia
1x
Grease Tray
1x Control Valve
adjustment
Screwdriver
1x Grill 1x Plate
1x
Hose & Regulator
Large Flare Guard
Check Table Below
Small Flare Guard
Check Table Below
GTR
SS GTR3 GTR3
SS GTR4 GTR4
SS GTR5 GTR5
SS GTR6 GTR6
SS
A011222233
B022223344
FLARE GUARDS QUANTITY FOR EACH BARBECUE MODEL
5
GTR SUPPORT KITS, HOOD AND LID
1. Remove the grease tray from the BBQ to install
the BBQ fascia with one of the kits.
Tucker GTR BBQs can be installed into a
non-combustible material with one of the
following Kits.
GTR BBQs can be installed with either a Flat Hinged
weather cover/ Lid or a Roasting Hood.
Make sure to read any separate instructions on
Assembly, Installation and Operation of the Roasting
Hood and / or Wok Burner if they are to be tted to
the BBQ.
- GTR Angle Support Kit
- GTR Side Panels Support Kit
GTR ANGLE SUPPORT KIT ASSEMBLY
2x Side Angles
2x
Fascia Brackets
4x
M6 Bolts
2x
Small Bolts
2x
Nuts
2x
Spacers
4x
Washers
To install GTR BBQ into Non-combustible you must
have one of the kits, depending if it’s going to
be hanging or sitting on the benchtop.
If you have a Flat Hinged Weather Cover/Lid,
attach the Lid onto the back of the BBQ with the
Phillips head bolts provided with the lid.
GTR Angle Support Kit Parts
6
2. First install the side angle hanging brackets to
the BBQ by installing the two bolts on each side.
3. Place the fascia brackets to the bottom of the
BBQ, by sliding them on the bottom BBQ vent
cover as per photo.
4. Screw the bolts on to the brackets.
5. Insert the bolt and spacer into the bracket hole
and secure it into the nut attached to the inner
part of the fascia as per photos.
The outer bolt screws into the BBQ pre-thread
hole, but the inner bolt it has to be secured with
a washer and nut.
7
Once the bolts are screwed into the fascia you
will be able to ip up the BBQ fascia to access
the grease tray.
GTR Side Panels Support Kit Parts
* Fascia Holes
*
*
Right side
Left side
2x
Side Panels
6x
M6 Bolts
2x
Small Bolts
2x
Spacers
GTR SIDE PANELS SUPPORT KIT ASSEMBLY
1. Remove the grease tray from the BBQ to install
the BBQ fascia kit.
2. Place the two side panels into the correct side of
the BBQ, than bolt the four bolts on each side.
4. After the installation is done the BBQ will look like
the one in the photo bellow.
3. Line up the fascia hole with the one of the side
panel, insert the spacer between the side panel
and the fascia and screw the bolt in, so it enable
the fascia to ip up.
Repeat this step for the other side.
8
1. First place the Flare Guards into the barbecue.
The Flare Guards are only required beneath the
stainless steel Cooking Grills.
Place the smaller Flare Guards directly above
the burners and place the larger Flare Guards
between the burners as per photos below.
6. Now place the Cooking Grills into the barbecue
above the Flare Guards and place the hot plate
beside the grills.
BARBECUE ASSEMBLY
8. If you have a GTR SS or GTR S Model BBQ,
then you will have a Wok Burner integrated
into the Body of the BBQ. Remove any cable
ties securing the Wok Trivet and then place it
back into position above the Wok Burner.
9. The SS Wok Burner can be tted with an optional
Hinged Flat Weather Cover/ Lid or a Roasting
Hood to protect it from the weather when not
in use. Read any Assembly, Installation and
Operation Instructions packaged with the
Roasting Hood if provided.
The Wok Trivet is used to support either a Wok or
Pot with a diameter of no less than 230mm.
The SS Wok has an optional Solid Hot Plate
available as an accessory, if you have one
it must be placed directly above the SS Wok
Burner allowing an equal air gap either side of
the Burner when it is in use.
9
INSTALLATION INSTRUCTIONS
& WARNINGS
BARBECUE INSTALLATION INSTRUCTIONS
INSTALLATION WARNINGS
READ THE IMPORTANT INFORMATION
ON THE FRONT OF THE BARBECUE
For installation onto a GTR trolley read relevant
instructions.
This barbecue is designed and approved for outdoor
use only.
Be mindful of the location of the installation of the
barbecue.
If you are using the roasting hood it is better that the
prevailing wind blows into the front of the BBQ during
cooking.
Do not use this appliance indoors or on marine craft.
This appliance shall only be used in an above
ground, open-air situation with natural ventilation,
without stagnant areas where gas leakage and
products of combustion are rapidly dispersed by
wind and natural convection.
Any enclosure in which the appliance is used shall
comply with one of the following:
• An enclosure with walls on all sides, but at least
one permanent opening at ground level and no
overhead cover. (gure 1)
• Within a partial enclosure that includes an
overhead enclosure and no more than two walls.
(gure 2 and 3)
• Within a partial enclosure that includes an
overhead cover and more than two walls, the
following shall apply. (gures 4 and 5)
• At least 25% of the total wall area is completely
open.
• At least 30% of the remaining wall area is open
and unrestricted.
• In the case of balconies, at least 20% of the total
of the side, back and front wall areas shall be
and remain open and unrestricted.
Strong winds blowing into the back or aross the
back of the hood whilst cooking with the hood
closed can cause overheating of the BBQ.
Hot air retained in the hood during cooking may
not be able to be released naturally from the
rear vent of the hood in strong winds.
DIAGRAMMATICAL REPRESENTATIONS OF
OUTDOOR AREAS
FIGURE F1 – OUTDOOR AREA – EXAMPLE 1
FIGURE F2 – OUTDOOR AREA – EXAMPLE 2
FIGURE F3 – OUTDOOR AREA – EXAMPLE 3
The following gures are diagrammatical
representations of outdoor areas. The areas
used in the gures below are examples – the
same principles apply to any other shaped
area.
Both ends open
10
FIGURE 4 OUTDOOR AREA –EXAMPLE 4
FIGURE F5 – OUTDOOR AREA – EXAMPLE 5
Open side at least 25%
of total wall area
30% or more in total of
the remaining wall area
is open and unrestrict-
ed.
OPEN AT SIDE AT LEAST 25% OF TOTAL WALL AREA. 30% OR
MORE IN TOTAL OF THE REMAINING WALL AREA IS OPEN
AND UNRESTRICTED
OPEN SIDE AT LEAST 25% OF TOTAL WALL AREA. 30% OR
MORE IN TOTAL OF THE REMAINING WALL AREA IS OPEN
AND UNRESTRICTED.
Open side at least 25%
of total wall area
30% or more in total of
the remaining wall area
is open and unrestrict-
ed.
Other manuals for GTR Series
3
This manual suits for next models
12
Table of contents
Other Tucker Barbecues Grill manuals
Tucker Barbecues
Tucker Barbecues GTR Series Assembly instructions
Tucker Barbecues
Tucker Barbecues GT Series Assembly instructions
Tucker Barbecues
Tucker Barbecues GTRL1 User manual
Tucker Barbecues
Tucker Barbecues GTR Series Instruction manual
Tucker Barbecues
Tucker Barbecues CHARCOAL DELUXE Assembly instructions
Tucker Barbecues
Tucker Barbecues Horizon Assembly instructions
Tucker Barbecues
Tucker Barbecues S Wok Assembly instructions
