TRENDnet TL2-G244 User manual
TL2-G244
1.01
Quick Installation Guide
Table of Contents
Version 11.05.2010
English 1
1. Before You Start
2. Hardware Installation 2
3. LEDs 3
4. Configure the Switch 5
1
Troubleshooting 9
1. Before You Start
Ÿ
ŸA computer with a network adapter properly installed
ŸCAT-5e or CAT-6 Network Cable
ŸThe surface must support at least 2.9 Kg (6.4 lbs) for the Switch
ŸThe power outlet should be within 1.8 meters (5.9 feet) of the Switch
ŸMake sure that there is proper heat dissipation from and adequate ventilation around the
Switch
ŸDo not place heavy objects on the Switch
Web Browser: Internet Explorer (6.0 or higher)
Ÿ
ŸMini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40, TEG-MGBS80,
TEG-MGBS10D35, TEG-MGBS40D35) for Mini-GBIC slots
EIA standard 19” rack
Package Contents
Ÿ
ŸMulti-Language Quick Installation Guide
ŸCD-ROM (User's Guide)
ŸRS-232 cable (3 m / 9.8 ft.)
ŸPower Cord (1.8 m / 5.9 ft.)
ŸRack Mount Kit
TL2-G244
Installation Requirements
Optional Equipment
1
2
2. Hardware Installation
Note:
The Mini-GBIC slots are shared with port 21, 22, 23 and 24 Gigabit Ethernet ports. When the
Mini-GBIC slots are in use, port 21, 22, 23, and 24 Gigabit Ethernet ports are disabled.
1. Connect the Power Cord to the TL2-G244 and
then to a power outlet.
2. Connect a Cat.5e or Cat.6 RJ-45 network
cable from the computer to an available
Ethernet port on the TL2-G244.
3. Move the Power switch to the on position.
4. Verify that the following panel lights are on:
PWR(Power), SYS(System) and 1000M
LINK/ACT, 10/100M LINK/ACT or 100M
LINK/ACT.
3
3. LEDs
PWR (Power)
SYS (System)
1000M LINK/ACT
10/100M LINK/ACT
100M LINK/ACT
4
N/A
Green
N/A
Green
Amber
Green
Amber
Gigabit Ethernet LED (RJ-45)
PWR (Power)
SYS (System)
1000M Link/ACT
2000Mbps (Full Duplex) Connected (per port)
2000Mbps (Full Duplex) Data Transmitting /
Receiving (per port)
2000Mbps (Full Duplex) Data Transmitting /
Receiving (per port)
100/200Mbps (Half/Full), 10/20Mbps (Half/Full),
or no connection to the port
100/200Mbps (Half/Full), 10/20Mbps (Half/Full),
or no connection to the port
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Connected (per port)
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Connected (per port)
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Data Transmitting/Receiving
(per port)
10/20Mbps (Half/Full Duplex) or 100/200Mbps
(Half/Full Duplex) Data Transmitting/Receiving
(per port)
2000Mbps (Full), or no connection to the port
2000Mbps (Full), or no connection to the port
Device powered On
Device is ready
Solid
Solid
Solid
Solid
Solid
Off
Solid
Off
Off
Off
Off
Off
Blinking
Blinking
Blinking
Blinking
Green
Device powered Off
Device is not ready
2000Mbps (Full Duplex) Connected (per port)
1000M Link/ACT
10/100M Link/ACT
100M Link/ACT
Device Status LED Color
Color
Sequence
Sequence
Definition
Definition
Combo Gigabit Ethernet
(RJ-45) / Mini-GBIC LED Color Sequence Definition
5
4. Configure the Switch
Note:
1. Before the Switch can be configured, a Static IP address must be assigned to your computer's
network adapter in the subnet of 192.168.10.x. Since the Switch's default IP address is
192.168.10.200, make sure no other network devices are assigned an IP address of
192.168.10.200. (Refer to Troubleshooting section on how to configure TCP/IP settings on your
PC.)
2. There are three methods of configuring the TL2-G244: Web Browser, Console Port and Telnet.
1. Using Web Browser
1. Open your web browser, type
http://192.168.10.200 in the Address bar, and
then press Enter.
2. Enter the User name and Password, and then
click Login. By default:
User Name: admin
Password: admin
3. Select the desired options for configuring the
switch.
6
Note:
A terminal program such as HyperTerminal is required to configure the switch via the Console
Port. The instructions shown below demonstrates how to configure the Switch on a Windows PC
using HyperTerminal.
2. Using the Console Port
2. Go to Start Ž Programs Ž Accessories Ž
Communications Ž HyperTerminal
1. Connect the RS-232 cable from a serial port on
your PC to the console port on the switch.
4. Select the correct COM port
(e.g. COM1, COM2) and then click OK.
3. Enter a name, choose an icon and then click
OK.
7
6. Press the Enter Key.
7. Enter the User Name for login. Then press the
Enter. Then Enter the Password and then
press Enter.
By default
login: admin
Password: admin
If you do not see the login prompt, please
power cycle the switch by unplugging the
power cord, wait 15 seconds and then plug it
back in.
5. Enter the following, click Apply and then click
OK.
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
The Telnet function may or may not be included with your computer's operating system. For
instructions on how to enable Telnet in Windows 7/Vista, please refer to the Troubleshooting
section.
3. Using Telnet
1. Click the Windows/ Start icon on the bottom left
hand corner and click All Programs.
8
2. Click Accessories and then click Command
Prompt.
3. Type in telnet 192.168.10.200. Then press the
Enter key.
4. Enter the User Name for login. Then press the
Enter. Then Enter the Password and then
press Enter. By default
login : admin
Password: admin
If you do not see the login prompt, please
power cycle the switch by unplugging the
power cord, wait 15 seconds and then plug it
back in.
Configuration is now complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TL2-G244 configuration and advanced settings,
please refer to User's Guide included on the Utility CD-ROM, or TRENDnet's website at
http://www.trendnet.com.
Other manuals for TL2-G244
3
Table of contents
Other TRENDnet Switch manuals
TRENDnet
TRENDnet TE100-S1616 User manual
TRENDnet
TRENDnet TK-208K User manual
TRENDnet
TRENDnet TI-PG541i User manual
TRENDnet
TRENDnet TEG-S50TXE SHEETS User manual
TRENDnet
TRENDnet TEG-160WS User manual
TRENDnet
TRENDnet TE100-S80g User manual
TRENDnet
TRENDnet TPE-T80H User manual
TRENDnet
TRENDnet TE100-S86FX User manual
TRENDnet
TRENDnet TK-207K - KVM Switch - USB Mounting instructions
TRENDnet
TRENDnet TE100-DS24 User manual
TRENDnet
TRENDnet TE100-S16 - DATA SHEETS User manual
TRENDnet
TRENDnet TK-802R User manual
TRENDnet
TRENDnet TPE-T88G User manual
TRENDnet
TRENDnet TEG-S80ES User manual
TRENDnet
TRENDnet TK-209K User manual
TRENDnet
TRENDnet TEG-S16g User manual
TRENDnet
TRENDnet TI-G50 User manual
TRENDnet
TRENDnet TE100-S24 - High Performance Auto-Sensing 10/100Mbps Fast Ethernet... User manual
TRENDnet
TRENDnet TPE-80WS - Web Smart PoE Switch User manual
TRENDnet
TRENDnet TK-804R User manual
