TOTALINE EZ3 User manual
Product Training Content
homeowner user guide
HOME SCREEN
Home Screen Layout 3
Home Screen Definitions 4
Wi-Fi Strength 5
Equipment Status 6
END USER SETTINGS
Set Point 8
Mode Screen 9
Fan 10
Settings Menu 11
Banner 12
Backlight 13
Filter 14
Lockout 15
Lockout pin 16
Clean Screen 17
Service 18
Date/Time 19
Humidity 20
De-Humidify 21
TABLE OF CONTENTS
2
USER INTERFACE
USER INTERFACE – HOME SCREEN
3
Equipment*Status
Wi/Fi*Signal*Strength
Page*Indicator
Room*Temperature
Banner
HOME SCREEN DEFINITIONS
SCREEN
SEGMENT
DEFINITION
Banner The Banner is used to provide status information to the end user
of the thermostat. The center portion of the Banner scrolls
through the selected Banner options chosen (every 3 seconds) in
the Settings – Banner Screen
Wifi Strength The left side of the Banner will display the current Wi-Fi signal
strength by the number of green bars displayed. A strong signal
will have a green dot with 3 arched bars over it. If the thermostat
has no current connectivity to a router the Wi-Fi icon will turn red.
Room
Temperature
The Room Temperature sensed by the thermostat. The
temperature is displayed in whole degrees. The default
temperature scale is degrees Fahrenheit, but can be changed to
degrees Celsius in the Installer Settings options
Page Indicator The Page Indicator at the bottom of the screen indicates which
top level screen is active. When the Home Screen is the active
screen the small house icon in the Page Indicator field is white
and the two dots to the left are grey and the two dots to the right
are grey.
Equipment
Status
The right side of the Banner displays the current Mode selected.
If the selected Mode icon is flashing, this is an indication that the
heating or cooling equipment associated with the current Mode is
actively heating or cooling.
4
HOME SCREEN – WIFI STRENGTH
DEFINITION DEPENDENCIES FUNCTION
The “Wireless Status Screen”
is invoked when the end user
presses the Wi-Fi Signal
Strength Button on the Banner.
This screen provides Wi-Fi
connectivity information.
Pressing the Disconnect Button
will remove connectivity to the
currently connected router,
placing the unit into Soft AP
mode so that the unit can
discover a new Wi-Fi router
network.
None Display Wi-Fi connectivity
information
5
HOME SCREEN- EQUIPMENT STATUS
DEFINITION DEPENDENCIES FUNCTION
The “Equipment Status” is invoked
when the end user presses the
Equipment Status Button on the
Banner. If the Fan Icon is shown
when the equipment status location is
pressed, the “Fan Screen” will be
invoked. If the Cooling Icon or
Heating Icon is shown when the
equipment status location is pressed,
the “Mode Screen” will be invoked.
None The icon displayed in the
“Equipment Status” area of the
screen will pulse off and on if
the equipment is currently
being activated, otherwise the
icon in this area will be on
solid. Available icons for this
area designate HEAT( ),
COOL ( ) or FAN mode/
operation ( ).
6
Equipment Status
END USER SETTINGS
END USER SETTINGS – SET POINT
DEFINITION DEPENDENCIES FUNCTION
The “Set point Screen” is used to
adjust the current heat set point
and cool set point. The orange
Heat Set point Wheel is used to
adjust the heat set point. The blue
Cool Set point Wheel is used to
adjust the cool set point.
If the thermostat is setup as a Non-Programmable
thermostat then the Play Button / Pause Button
and associated text above and below these
buttons will not be present. If the thermostat is
setup in a Heat Only configuration then the Cool
Setpoint Wheel will be greyed and disabled. If the
thermostat is setup in a Heat Only configuration
then the Cool Setpoint Wheel will be greyed and
disabled.
An indoor equipment type must be
chosen so that an airflow source is
available to the system operation.
The two types of indoor equipment
defined for operation are a
FURNACE and an AIR HANDLER
(sometimes also referred to as a FAN
COIL). The indoor equipment is not
required to have a heat source
present, which is selectable with the
Indoor Equipment Stages setting. If
control of a PACKAGE UNIT is
desired and the PACKAGE UNIT has
a natural or propane heating source
installed, the FURNACE option
should be selected.
8
Scroll
Available
on APP
END USER SETTINGS – MODE SCREEN
DEFINITION DEPENDENCIES FUNCTION
The “Mode Screen” is used to
allow the end user to see and
change the currently selected
mode. The center of this screen
displays the Off Mode Button, the
Heat Mode Button, the Cool Mode
Button, the Auto Mode Button, and
the Emergency Heat Mode Button.
The horizontal yellow Mode
Selected Bar is always shown
above the mode that has been
selected by the end user.
Some modes may not be available
based on the Indoor Equipment Type
or the Outdoor Equipment Type
selections. An example of a system
without any Cooling or Aux Heating
equipment selected is shown in the
right most screen shown above. The
Cool Mode Button, the Auto Mode
Button, and the Emergency Heat
Mode Button in this screen (and
associated text) is “greyed” to
indicate that these options are not
available and the buttons cannot be
selected.
Changing from one mode to another mode will not
affect operation of the thermostat until the newly
selected Mode Button has been selected for at
least 10 seconds. Changing from one mode to
another (e.g. Heat mode to Cool mode) will first
require that the thermostat first satisfy any
Minimum ON Timer requirements and then will
restart the Minimum OFF Timer that will be
required to expire before equipment will be turned
on in the new mode. Going from any Heating or
Cooling Mode to Off Mode will immediately shut
off an equipment that is active (after the 10
second mode button requirement is satisfied).
9
Scroll
Mode*Selected*Bar
Available
on APP
Other manuals for EZ3
1
Table of contents
Other TOTALINE Thermostat manuals
TOTALINE
TOTALINE 1 For All User manual
TOTALINE
TOTALINE P374-1 900 User manual
TOTALINE
TOTALINE 1 For All P374-1000FM User manual
TOTALINE
TOTALINE P474-1020 User manual
TOTALINE
TOTALINE P/N P474-2150 User manual
TOTALINE
TOTALINE P374-2300FM User manual
TOTALINE
TOTALINE Gold P274-1100 User manual
TOTALINE
TOTALINE 1 For All User manual
TOTALINE
TOTALINE P374-1800 User manual
TOTALINE
TOTALINE P710U-21PHP User manual
TOTALINE
TOTALINE Smart P330-0110 User manual
TOTALINE
TOTALINE 1 For All User manual
TOTALINE
TOTALINE P374-2 700 User manual
TOTALINE
TOTALINE Gold P274-1100 User manual
TOTALINE
TOTALINE EZ3 Manual
TOTALINE
TOTALINE P274-21 00 User manual
TOTALINE
TOTALINE Comfort Call P374-0433 User manual
TOTALINE
TOTALINE Signature CPV230LA User manual
TOTALINE
TOTALINE P700U-21NHP User manual
TOTALINE
TOTALINE Programmable Thermostat Assembly instructions
Popular Thermostat manuals by other brands
Saswell
Saswell SAS920XWHB-7-S-RF User manual and warranty card
Aircalo
Aircalo TFP1-ET85P2 operating manual
Honeywell
Honeywell CM721 user manual
Carrier
Carrier DEBONAIR 33CS Installation and operating instructions
Lennox
Lennox iHarmony Zone Thermostat Installation and setup guide
Gemtech
Gemtech GT7000 Operation
