Toshiba Strata DK Backup Service manual
Strata® DK
Technical Bulletin
Toshiba America Information Systems, Inc.
Telecommunication Systems Division
9740 Irvine Blvd., Irvine, CA 92618-1697 (949) 583-3700
http://telecom.toshiba.com
726+,%$
4031068
DK424 to DK424i Upgrade
Procedure Using DKi Admin
This bulletin describes how to upgrade the DK424 to a DK424i system. It also lists the upgrade paths for
various DK424 processors, provides system capacity and line considerations, along with reconfiguration
examples and blank configuration worksheets.
Upgrade Considerations
Upgrade Paths – The following is a list of possible DK424 to DK424i upgrade paths:
♦RCTU A processors (R1~4.x) >> B1, B2, B3, B5 processors
♦RCTU B processors (R1~4.x) >> B2, B3, B5 processors
♦RCTUC/D processors (R1~4.x) >> B3 & B5 processors
♦RCTU E/F processors (R3~4.x) >> B5 processors
Note For a specific list of all processors, see Page 6 of this bulletin.
System Capacity Verification – Make sure the DK424i system you are upgrading to provides enough
PCB slots, station ports, and CO lines to match the existing DK424 system (see tables below).
DK424i Maximum System Capacities with only Digital T1/PRI Line PCBs
B1CU B2CAU/B2CBU B3CAU/B3CBU B5CAU/B5CBU
1 Cabinet
8 Universal slots
56 Stations Max.
32 T1/PRI lines Max.
64 Stations & Digital lines
2 Cabinets
14 Universal slots
112 Stations Max.
120 T1/PRI lines Max.
128 Stations & Digital lines
3 Cabinets
28 Universal slots
192 Stations Max.
120 T1/PRI lines Max.
248 Stations & Digital lines
5 Cabinets
48 Universal slots
336 Stations Max.
196 T1/PRI lines Max.
432 Stations & Digital lines
DK424i Maximum System Capacities with only Analog Line PCBs
B1CU B2CAU/B2CBU B3CAU/B3CBU B5CAU/B5CBU
TBDK-0042
November 2000
November 2000 Configuring DK424i Cabinets with DK424 PCBs
DK424 to DK424i Upgrade Procedure Using DKi Admin
2 of 7
Configuring DK424i Cabinets with DK424 PCBs
RCTU, R1~R3 Software with Tie and/or DID Lines
♦When installing PCBs in the DK424i cabinets, all PCBs must be installed in the same order in relation
to each other as they were in the DK424 cabinets. You may have to skip slots in the new cabinets to
place RDTU PCBs into the allowed slots.
♦Only install the PCBs that currently exist in the DK424 cabinets into the DK424i cabinets –do not add
more line or station PCBs during the upgrade. The only exception to this rule is that you can add an
RSIU, PIOU, PIOUS, RSSU.
RCTU, R1~R3 Software Without Tie/DID, or any R4.x Software With or
Without Tie/DID Lines
♦Only install the PCBs that currently exist in the DK424 cabinets into the DK424i cabinets –do not add
more line or station PCBs during the upgrade. The only exception to this rule is that you can add an
RSIU, PIOU, PIOUS, RSSU.
♦When installing PCBs in the DK424i cabinets, all station PCBs and the RATU must be installed in the
same order in relation to other station PCBs as they were in the DK424 cabinets.
♦When installing PCBs in the DK424i cabinets, all CO line PCBs must be installed in the same order in
relation to other CO line PCBs as they were in the DK424 cabinets.
♦When moving station PCBs from DK424 to DK424i cabinets, you do not have to installed them in the
same order in relation to CO line PCBs, and vice-versa .
♦Do not skip slots except when necessary for RDTU, RPTU, and RWIU. Make sure these PCBs are
installed in the correct cabinet slot per Worksheet 6 of the Strata DK I&M Manual, Chapter 6 –
DK424i Configuration.
♦PIOU, PIOUS, RSSU, etc., can be installed in any DK424i slot that does not conflict with RDTU,
RPTU or RWIU vacant slots. These PCBs do not have to be installed in any order corresponding to
where they were installed in DK424 cabinets. The RSIU must be installed in slot S101.
1 Cabinet
8 Universal slots
56 Stations Max.
32 CO lines Max.
64 Stations & Analog lines
2 Cabinets
14 Universal slots
104 Stations Max.
120 CO lines Max.
112 Stations & Analog lines
3 Cabinets
28 Universal slots
192 Stations Max.
120 CO lines Max.
248 Stations & Analog lines
5 Cabinets
48 Universal slots
336 Stations Max.
200 CO lines Max.
376 Stations & Analog lines
November 2000 Configuring DK424i Cabinets with DK424 PCBs
DK424 to DK424i Upgrade Procedure Using DKi Admin
Preliminary andConfidential
3 of 7
Reconfiguration Example: The following tables show two examples of how to load DK424i cabinet slots from
the same DK424, RCTU E/F R4, system.
T=Telephone type PCB
L=CO Line type PCB
Existing DK424 Cabinets Example 1, DK424i Cabinets Example 2, DK424i Cabinets
Slot PCB T/L No. Slot PCB T/L No. Slot PCB T/L No.
R11 RCTUE B101 B5CAU B101 B5CAU
RCTU RCTUF B102 B5CBU B102 B5CBU
S11 RSIU S101 RSIU S101 RSIU
S12 PDKU T1 S102 PDKU T1 S102 PDKU T1
S13 RSTU T2 S103 RDTU L1 S103 RSTU T2
S14 PEKU T3 S104 VACANT L1 S104 PEKU T3
S15 RDTU L1 S105 RCOU L2 S105 RDTU L1
S16 VACANT L1 S106 RSTU T2 S106 VACANT L1
S21 RCOU L2 S107 RPTU L3 S107 RCOU L2
S22 PEKU T4 S108 VACANT L3 S108 PEKU T4
S23 RPTU L3 S201 PEKU T3 S201 PDKU T5
S24 VACANT L3 S202 PEKU T4 S202 PDKU T6
S25 PDKU T5 S203 RCOU L4 S203 RPTU L3
S26 PDKU T6 S204 RCOU L5 S204 VACANT L3
S27 RCOU L4 S205 REMU L6 S205 RCOU L4
S28 RCOU L5 S206 PDKU T5 S206 PDKU T7
S31 REMU L6 S207 PDKU T6 S207 RCOU L5
S32 PDKU T7 S208 PDKU T7 S208 RSTU T8
S33 RSTU T8 S209 RSTU T8 S209 PEK T9
S34 PEKU T9 S210 PEKU T9 S210 PDKU T10
S35 PDKU T10 S301 RDTU L7 S301 RDSU T11
S36 RDSU T11 S302 VACANT S302 REMU L6
S37 PDKU T12 S303 PDKU T10 S303 RDTU L7
S38 PDKU T13 S304 RDSU T11 S304 VACANT L7
S41 RDTU L7 S305 PDKU T12 S305 PDKU T12
S42 VACANT L7 S306 PDKU T13 S306 PDKU T13
S43 PDKU T14 S307 PDKU T14 S307 PDKU T14
S44 RDDU L8 S308 PESU T15 S308 RDDU L8
S45 PESU T15 S309 PDKU T16 S309 RESU T15
S46 PDKU T16 S310 RDDU L8 S310 RCOU L9
S47 RSTU T17 S401 RCOU L9 S401 PDKU T16
S48 RCOU L9 S402 RSTU T17 S402 RSTU T17
S51 PDKU T18 S403 PDKU T18 S403 PDKU T18
S52 S404 S404
S53 S405 S405
November 2000 DKi Admin Upgrade Procedure (DK424 to DK424i)
DK424 to DK424i Upgrade Procedure Using DKi Admin
4 of 7
DKi Admin Upgrade Procedure (DK424 to DK424i)
1. When upgrading from a DK424 (RCTU) to DK424i (BxCU), use DKi Admin to download the
complete RCTU database (F2 then F3 from Backup/Restore Data).
Note After the download, use the DKi Admin “Transfer DK Data”function to transfer this data to a
floppy in case you need to restore the data back to the RCTU processor.
2. Before proceeding with DKi Admin, complete either the On-site Upgrade or Off-site Upgrade:
Important! Make sure all PCBs are installed and/or programmed correctly with Program 03 in the
DK424i before uploading data to the DK424i processor.
3. Connect the DKi Admin PC to the TTY port in the DK424i base cabinet and then set up the TTY
port/communications parameters using the programming telephone.
4. Go to the Select Customer menu and select the RCTU data that was downloaded in Step 1 above. (The
data you want to upload to the new DK424i processor).
5. Go to the Backup/Restore menu and type the DK Code 0000.
6. When you see the “DK System Program File screen”press F5 and follow the Processor Conversion
prompts to upgrade and send data to the DK424i processor.
7. Step 6 prompts you to send the RCTU data to the BxCU processor and then pull it back. Once the data
is pulled back, go back to the “Select Customer”menu and reselect the customer database; then check
the cabinet diagram.
Important! After the upgrade is complete, you must use DKi Admin to re-set Program 12-9
(recommended value is 04 sec.) and all slot related programs (Prg. 19, *42-1~2, and *60).
On-site
Upgrade
1. Install the new BxCU processor and all other PCBs from the DK424 cabinets
into the DK424i cabinets and then initialize the BxCU from the programming
telephone (follow the PCB configuration rules shown on the previous page).
2. After initialization, use the programming telephone to check/enter Program 03
PCB codes for each cabinet slot.
Off-site
Upgrade
1. Install the programming telephone and TTY port PCB into a DK424i base
cabinet. Install the new BxC processor into the DK424i base cabinet and
initialize it from the programming telephone.
2. After initialization, use the programming telephone to enter Program 03 PCB
codes for each cabinet slot (follow the PCB configuration rules shown on the
previous page).
November 2000 DKi Admin Upgrade Procedure (DK424 to DK424i)
DK424 to DK424i Upgrade Procedure Using DKi Admin
Preliminary andConfidential
5 of 7
Upgrade Configuration Worksheet (copy additional sheets as necessary)
DK424 Cabinets DK424i Cabinets
Cab 1 Slots PCB T/L Cab 4 Slots PCB T/L Cab 1 Slots PCB T/L Cab 4 Slots PCB T/L
R11 S51 B101 S401*
RCTU S52 B102 S402
S11 S53 S101 S403*
S12 S54 S102 S404
S13 S55 S103* S405*
S14 S56 S104 S406
S15 S57 S105* S407
S16 S58 S106 S408
S107* S409
Cab 2 Slots PCB T/L Cab 6 Slots PCB T/L
S21 S61 Cab 2 Slots PCB T/L Cab 5 Slots PCB T/L
S22 S62 S201* S501*
S23 S63 S202 S502
S24 S64 S203* S503*
S25 S65 S204 S504
S26 S66 S205* S505*
S27 S67 S206 S506
S28 S68 S207 S507
S208 S508
Cab 3 Slots PCB T/L Cab 7 Slots PCB T/L S209 S509
S21 S71 S210 S510
S22 S72
S23 S73 Cab 3 Slots PCB T/L
S24 S74 S301*
S25 S75 S302
S26 S76 S303*
S27 S77 S304
S28 S78 S305*
S306
Cab 4 Slots PCB T/L S307
S41 S308
S42 S309
S43 S310
S44
S45
S46
S47
S48
Notes:
T=Telephone type PCB
L=CO line type PCB
*= Allowed T1/PRI slots
The Base cabinet allows Spkr
OCA and DIU data with PDKU
in all slots; expansion cabinets
provide these features in slots
S_01~S_06 only.
Last available slot: B1C=S108,
B2C=206, B3C=310, and
B5C=510.
November 2000 Strata DK Processor Upgrade Paths
DK424 to DK424i Upgrade Procedure Using DKi Admin
6 of 7
Strata DK Processor Upgrade Paths
DK14 (contains DK Release 3.1 software)
♦Upgrade DK14 to: DK16e or DK40 or DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/
D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU
or B5CAU/B5CBU.
DK16e (contains DK Release 3.1 software)
♦Upgrade DK16e to: DK40 or DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/D3 or
RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or
B5CAU/B5CBU.
DK40 (contains DK Release 3.1 software)
♦Upgrade DK40 to: DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/D3 or RCTUC3/D4
or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
DK40i (contains DK424 Release 4.3 software)
♦Upgrade DK40i to: RCTUA4 or RCTUBA3/RCTUBB4 or RCTUC3/D4 or RCTUE3/F4 or B1CU or
B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
DK280, RCTU R1/R2 (contains DK Release 1.0 or Release
2.0 software)
♦Upgrade RCTUA1 to: RCTUB2 or RCTUBA3/RCTUBB3 or RCTUBA3/RCTUBB4 or RCTUC1/
D2 or RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or
B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUB2 to: RCTUBA3/RCTUBB3 or RCTUBA3/RCTUBB4 or RCTUC1/D2 or or
RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B2CAU/B2CBU or B3CAU/B3CBU
or B5CAU/B5CBU.
♦Upgrade RCTUC1/D2 to: RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B3CAU/
B3CBU or B5CAU/B5CBU.
DK424, RCTU R3.x (contains DK Release 3.0 or Release 3.2
software)
♦Upgrade RCTUA3 to: RCTUBA3/RCTUBB3 or RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or
RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUBA3/RCTUBB3 to: RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4
or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUC3/D3 to: RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B3CAU/B3CBU or
B5CAU/B5CBU.
♦Upgrade RCTUE3/F3 to: RCTUE3/F4 or B5CAU/B5CBU.
November 2000 DK424, RCTU R4.x (contains DK Release 4.0, Release 4.15 or Release 4.3 software)
DK424 to DK424i Upgrade Procedure Using DKi Admin
Preliminary andConfidential
7 of 7
DK424, RCTU R4.x (contains DK Release 4.0, Release 4.15
or Release 4.3 software)
♦Upgrade RCTUA4 to: RCTUBA3/RCTUBB4 or RCTUC3/D4 or RCTUE3/F4 or B1CU or B2CAU/
B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUBA3/RCTUBB4 to: RCTUC3/D4 or RCTUE3/F4 or B2CAU/B2CBU or B3CAU/
B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUC3/D4 to: RCTUE3/F4 or B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade RCTUE3/F4 to: B5CAU/B5CBU.
DK424i, BxC (contains DK Release 4.3 software)
♦Upgrade B1CU to: B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade B2CAU/B2CBU to: B3CAU/B3CBU or B5CAU/B5CBU.
♦Upgrade B3CAU/B3CBU to: B5CAU/B5CBU.
Other manuals for Strata DK Backup
16
This manual suits for next models
2
Table of contents
Other Toshiba Software manuals
Toshiba
Toshiba Strata CTX ACD Application User manual
Toshiba
Toshiba Strata CIX SoftIPT 2.2 User manual
Toshiba
Toshiba Strata CIX WinCIX Service manual
Toshiba
Toshiba STRATA CIX Remote Call Control Service manual
Toshiba
Toshiba T-PSV User manual
Toshiba
Toshiba STRATA CS Commutation Server User manual
Toshiba
Toshiba HDWC110XK3J1 User manual
Toshiba
Toshiba 6F3A4508 User manual
Toshiba
Toshiba STRATA CIX Net Server User manual
Toshiba
Toshiba STRATA CIX Service manual
Toshiba
Toshiba TDP-TW350U User manual
Toshiba
Toshiba VIPedge User manual
Toshiba
Toshiba Strata CS Release 7.0 Manual
Toshiba
Toshiba Strata CIX SoftIPT 2.1.2 User manual
Toshiba
Toshiba STRATA CIX Net Server Service manual
Toshiba
Toshiba RSM 100 User manual
Toshiba
Toshiba Strata CIX Database Assistant Service manual
Toshiba
Toshiba STRATA CIX Owner's manual
Toshiba
Toshiba Strata CS User manual
Toshiba
Toshiba Strata AirLink DK424 User manual
