Sun Microsystems Fire 6800 User manual
Sun Fire™6800 System Hold-down Kit
This document describes how to update the doors and bolt your system to the floor.
Install the Door Supports
1. Unlock and open the cabinet door.
2. Pull down the upper hinge pin, lift the door off the lower hinge pin and remove the door.
Caution – Do not perform Step 3 in the computer room. Drilling the metal door in the computer
room could lead to metal contamination.
3. Drill out the four rivets on the door that secure the door restraint bracket.
Use a number 30 or 1/8-inch drill bit.
4. Secure the new door restraint bracket using the four POP rivets provided. See figure.
The tool to secure the POP rivets is not provided.
Note – This new door restraint provides both vertical and horizontal stability so the cabinet door doesn’t
bend the upper and lower hinge brackets.
5. Reinstall the cabinet door.
6. Repeat Step 1 through Step 5 for the other cabinet door.
Install the Hold Down Brackets
1. Determine mounting hole locations in the site floor.
Optimize system location based on air flow and structural requirements of the operating site. Use the
diagram below for hole location reference.
Caution – Examine site blueprints to ensure that no pipes or wires run beneath the operating
location.
2. Move the system away from the operating location to provide space for drilling.
Note – NEBS Zone 4 earthquake brackets have been tested by Sun Microsystems for installation directly to a
concrete floor. As the performance of connection systems onto reinforced raised floors can vary, a qualified
structural engineer should be consulted prior to installation on a raised floor.
Note – Because each operating location is unique, the bolts that secure the NEBS Zone 4 earthquake bushing
to the site floor must be supplied by personnel at the site. High strength bolts (or alloy threaded rod) with a
maximum diameter of 1/2 inch can be used
Note – Use a vacuum to prevent air contamination in the computer room while drilling.
3. Drill four mounting holes in the site floor in the locations determined in Step 1.
4. Move the system back to the operating location.
16.88 in.
(428.86 mm)22.66 in.
(575.66 mm)
46.00 in.
(1168.6 mm)
44.47 in.
(1129.6 mm)
2.11 in.
(54.0 mm)
2.91 in.
(74.0 mm)
0.51 in.
(13.00 4 PL)
5. Release the catches and remove the kick-panels.
The kick-panels snaps off.
6. Remove the inner and outer kick-panel brackets.
Discard the outer kick-panel brackets. Save the bolts andd the inner kick-panel brackets for Step 7.
7. Place the NEBS Zone 4 earthquake bracket between the new outer kick-panel bracket and the inner
kick-panel bracket and secure the assembly to the cabinet using the existing bolts.
Note – It may be necessary to adjust the cabinet leveling pads to align the NEBS Zone 4 earthquake bracket.
8. Repeat Step 6 and Step 7 for the remaining kick-panel brackets.
Caution – Before you begin drilling examine site blueprints to ensure that no pipes or wires run
beneath operating location.
9. Secure all four bracket assemblies to the floor.
Use a vacuum to prevent air contamination in the computer room while securing the bracket assemblies.
10. Push the kick-panels back into place.
The retainers will snap into place.
NEBS Zone 4
Inner kick-panel bracket
Outer kick-panel bracket
earthquake bracket
Accessing Sun Documentation
You can view, print, or purchase a broad selection of Sun documentation, including localized versions, at:
http://www.sun.com/documentation
Contacting Sun Technical Support
If you have technical questions about this product that are not answered in this document, go to:
http://www.sun.com/service/contacting
Sun Welcomes Your Comments
Sun is interested in improving its documentation and welcomes your comments and suggestions. You can
submit your comments by going to:
http://www.sun.com/hwdocs/feedback
Please include the title and part number of your document with your feedback:
Sun Fire 6800 System Hold-down Kit, part number 817-2664-12
Part No. 817-2664-12, Rev. A
October 2003
Sun Microsystems, Inc.
www.sun.com
Copyright 2003 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms. Third-party software, including font technology, is copyrighted and licensed from Sun
suppliers. Portions may be derived from Berkeley BSD systems, licensed from U. of CA. Sun, Sun Microsystems, the Sun logo, and Solaris are trademarks or registered trademarks
of Sun Microsystems, Inc. in the U.S. and in other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International,
Inc. in the U.S. and in other countries. U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and
applicable provisions of the FAR and its supplements.
Copyright 2003 Sun Microsystems, Inc. Tous droits réservés. Distribué par des licences qui en restreignent l’utilisation. Le logiciel détenu par des tiers, et qui comprend la
technologie relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Des parties de ce produit pourront être dérivées des systèmes
Berkeley BSD licenciés par l’Université de Californie. Sun, Sun Microsystems, le logo Sun, et Solaris sont des marques de fabrique ou des marques déposées de Sun
Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de
SPARC International, Inc. aux Etats-Unis et dans d’autres pays.
Other manuals for Fire 6800
8
Table of contents
Other Sun Microsystems Server manuals
Sun Microsystems
Sun Microsystems Sun Fire V890 User manual
Sun Microsystems
Sun Microsystems Sun Fire V445 Instruction Manual
Sun Microsystems
Sun Microsystems Sun Fire X2100 User manual
Sun Microsystems
Sun Microsystems Netra 1290 Instruction Manual
Sun Microsystems
Sun Microsystems Fire 6800 User manual
Sun Microsystems
Sun Microsystems Fire 6800 User manual
Sun Microsystems
Sun Microsystems Sun N2000 Series Reference manual
Sun Microsystems
Sun Microsystems Netra ct User manual
Sun Microsystems
Sun Microsystems Sun Fire V20z Instruction sheet
Sun Microsystems
Sun Microsystems Fire F6800 User manual
Sun Microsystems
Sun Microsystems Fire V210 User manual
Sun Microsystems
Sun Microsystems Sun Fire V890 Installation instructions manual
Sun Microsystems
Sun Microsystems Blade X8400 User manual
Sun Microsystems
Sun Microsystems Sun SPARC Enterprise M4000 User manual
Sun Microsystems
Sun Microsystems Netra X4200 M2 Manual
Sun Microsystems
Sun Microsystems Sun Fire T1000 User manual
Sun Microsystems
Sun Microsystems SUN FIRE 280R Service manual
Sun Microsystems
Sun Microsystems Sun Fire T2000 User manual
Sun Microsystems
Sun Microsystems Fire 4810 Installation instructions manual
Sun Microsystems
Sun Microsystems Fire V210 User manual
