Strong SRT 6201 User manual

www.strong.tv

Picture similar

User Manual

Bedienungsanleitung

Manuel d'Utilisateur

Istruzioni d’uso

Uputstvo za upotrebu

Руководство пользователя

Digital Satellite Receiver SRT 6201

PART 1 • English

English

CONTENT

1.0 1 INTRODUCTION 2

1.1 Safety Instructions 2

1.2 Storage 2

1.3 Equipment Set-up 3

1.4 Accessories 3

1.5 Usage of external USB devices 3

2.0 2 YOUR RECEIVER 3

2.1 Rear Panel 3

2.2 Remote Control Unit 3

2.3 Default PIN code: 0000 4

3.0 CONNECTIONS 4

3.1 Basic connection with SCART cable 4

3.2 Connecting to Satellite Dish 4

3.3 Connecting USB device 4

4.0 STARTING UP 5

4.1 Language Selection 5

4.2 Select Satellite 5

4.3 Antenna mode 5

5.0 MAIN MENU 6

5.1 Channel Organiser 6

5.2 Installation 6

5.3 System setting 7

5.4 Timer 10

5.5 Multimedia 10

6.0 WATCHING TV AND LISTENING TO THE RADIO 10

6.1 Programme Information 10

6.2 EPG (Electronic Programme Guide) 10

6.3 Changing channel list modes 11

6.4 Audio language selection 11

6.5 TELETEXT function 11

6.6 Subtitles function 11

7.0 TROUBLE SHOOTING 12

8.0 SPECIFICATIONS 13

STRONG declares that this item complies with the basic

requirements and other relevant regulations of directives

CE 2004/108/EEC and 73/23EEC; RoHS 2002/95EEC

Subject to alterations. In consequence of continuous research

and development technical speciﬁcations, design and appearance

of products may change. All product names are trademarks or

registered trademarks of their respective owners.

22 Dec 2011 15:36

PART 1 • English

STRONG declares that this item complies with the basic requirements and other relevant

regulations of directives

CE 2004/108/EEC and 73/23EEC

RoHS 2002/95EEC

Subject to alterations. In consequence of continuous research and development technical

speciﬁcations, design and appearance of products may change. All product names are trademarks

or registered trademarks of their respective owners.

1.0 1 INTRODUCTION

1.1 Safety Instructions

DO NOT INSTALL YOUR RECEIVER:

 In a closed or poorly ventilated cabinet; directly on top of or under any other equipment;

on a surface which might obstruct the ventilation slots.

DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:

 To direct sunlight or near any other equipment that generates heat; to rain or intense

moisture; to intense vibration and to any shock which may cause permanent damage to

your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.

 Do not use a damaged power cord. It may cause a ﬁre or an electrical shock. Do not

touch a power cord with wet hands. It may cause an electric shock.

 When the receiver is not used for a long period of time, you should unplug the power

cord from the wall socket.

 Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you

may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap

solution, only after disconnecting from the mains voltage supply. Make sure no foreign

objects fall through the ventilation slots because this could cause ﬁre or an electric shock.

 Do not place any objects on top of the receiver because this might prevent proper cooling

of the components inside.

Safety Precautions

 Never open the receiver cover. It is dangerous to touch the inside of the receiver due to

high voltage currents and possible electrical hazards and your warranty will be void. Refer

all maintenance or servicing to suitably qualiﬁed personnel.

 When you are connecting cables, be sure that the receiver is disconnected from the

mains supply voltage. Wait a few seconds after switching off the receiver before you move

the receiver or disconnect any equipment.

 It is a necessity that you only use an approved extension and compatible wiring that

is suitable for the electrical power consumption of the installed equipment. Please

ensure that the electrical power supply corresponds with the voltage on the electrical

identiﬁcation plate at the back of the receiver.

If the receiver does not operate normally even after strictly following the instructions in this user

manual, it is recommended to consult your dealer.

1.2 Storage

Your receiver and its accessories are stored and delivered in a packaging designed to protect against

electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep

the packaging away from children. For transporting the receiver from one place to another or if you

are returning it under warranty conditions, make sure to repack the receiver in its original packaging

with its accessories. Failing to comply with such packaging procedures could void your warranty.

PART 1 • English

English

1.3 Equipment Set-up

We recommend you consult a professional installer to set up your equipment. Otherwise, please

follow the instructions below:

 Refer to the user manual of your TV and your antenna.

 Make sure that the SCART cable and outdoor components are in a good condition and

the SCART connections are well shielded

This manual provides complete instructions for installing and using this receiver. The following

symbols will serve as follow.

WARNING: Indicates warning information.

TIPS: Indicates any other additional important or helpful information.

MENU Represents a button on the remote control or the receiver. (Bold Character)

Move to Represents a menu item within a window. (Italic Character)

1.4 Accessories

 User Manual

 1 Remote control unit

 2x Batteries (AAA type)

NOTE: The batteries should not be recharged, disassembled, electrically short-circuited,

be mixed or used with other types of batteries. If rechargeable accumulators

instead of batteries are going to be used, we recommend using (e.g. NiMH) types

with low self-discharge to ensure long time operation of remote control.

1.5 Usage of external USB devices

 It is recommended to use USB 2.0 storage devices. If your device is not compatible to

USB 2.0 speciﬁcations, playback and other multimedia functions of the receiver would

not work properly.

 STRONG cannot guarantee compatibility to all types of USB storage devices.

 If you are going to use external USB HDD (Hard Disk Drive) please consider that it might

be the case that the power speciﬁcations exceed the supported output of your receiver

(5V/500mA). If so, please connect your USB HDD to an according external power

adapter.

2.0 2 YOUR RECEIVER

2.1 Rear Panel

Fig. 2

1. SAT OUT To connect an extra receiver to the satellite signal from dish

2. SAT IN To connect to the LNB for satellite signal from dish

3. TV SCART To connect to your TV set using a SCART cable.

4. S/PDIF Digital audio output

To connect to the input of your digital audio ampliﬁer.

5. Power Cord Your receiver requires a power supply of 100~240 V AC (Auto-

selectable), 50/60Hz +/-5%. Make sure to check the power

speciﬁcation before connecting your receiver to the wall outlet.

2.2 Remote Control Unit

Fig. 3

1. q Turns the receiver On/Standby.

2. ! Mutes the audio outputs of the receiver.

3. 0~9 Changes channel and controls numeric functions

PART 1 • English

4. AV Toggles between TV and receiver (AV) mode

5. TV/R Toggles between TV or radio mode

6. MENU Opens the main menu

7. EXIT Exits from the menu or sub-menu and cancels the progressing

function if applicable.

8. p/q Changes the current programme to the previous/next programme

in TV mode.

Moves the cursor up/down in menu mode.

9. t/u Increases/decreases the volume level in viewing mode.

Changes the setting values in speciﬁc menu item in menu mode.

10. OK Activates the highlighted menu item. Displays the channel list in

viewing mode according to the selected list.

11. FAV Opens the FAV list and toggles the favourite mode.

12. EPG Shows the EPG (Electronic Programme Guide) in viewing mode.

13. V+ / V- Increases/decreases the receiver volume level

14. INFO Shows information banner

15. AUDIO Selects available audio language(s) for the watched channel.

Selects stereo ((•)), left-mono ((• or right-mono •)).

16. ZOOM Opens Zoom selection for the desired part of watched channel/

picture

17. P+/P- Page up and down in all list modes

18. SAT/RED Selects satellite list in channel list mode

19. TEXT/GREEN Opens the current Teletext of a channel (if available)

20. SUB/YELLOW Shows the list of subtitle languages available for the current

channel

21. RCL/BLUE Opens the list of last watched channels

22. 2 Freezes/resumes video or playback

23. : Jump backwards during playback

24. " Jump forwards during playback

25. 4 No function

26. u To playback ﬁles in multimedia mode

27. 5 Fast backward in multimedia mode

28. 6 Fast forward in multimedia mode

29. 3 Stop in multimedia mode

2.3 Default PIN code: 0000

3.0 CONNECTIONS

3.1 Basic connection with SCART cable

Fig. 4

3.2 Connecting to Satellite Dish

Connecting a ﬁxed satellite dish to your receiver

Fig. 5

Connecting multiple ﬁxed dishes to your receiver using a DiSEqC 1.0 switch

Fig. 6

3.3 Connecting USB device

Fig. 7

PART 1 • English

English

4.0 STARTING UP

Ensure your satellite signal is of good quality. It is recommended that you perform the ﬁrst time

installation following the Installation Wizard step by step. It will help you to easily achieve system

conﬁguration and channel installation.

4.1 Language Selection

Press p/q to choose your language, press OK to conﬁrm. The Select Satellite menu will appear.

Further installation steps are depending on the satellite where your dish is aimed to.

4.2 Select Satellite

a) Your dish is aimed at Astra 1C, 1E, 1F or HOT BIRD satellite.

Press p/q to select the ASTRA or HOT BIRD satellite and press OK. Follow the instructions. When

you have ﬁxed your dish at the correct position choose NEXT and press OK. The Channel Setup

menu will appear.

NOTE: If OSD language “German” and satellite “Astra 19.2E” are chosen, the receiver will

automatically load German pre-installed channels at the beginning of the channel

list.

If OSD language “Italian” and satellite “HOT BIRD 13E” are chosen, the receiver will automatically

load Italian pre-installed channels at the beginning of the channel list.

b) Your dish is aimed at another satellite

Select Other in the Select satellite menu and press OK. A list of satellites will be listed. If you select

one out of the satellite list, the Conﬁgure Antenna menu will appear. Use this menu to set the

LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and

Antenna mode.

4.3 Antenna mode

a) Fixed dish

Set Antenna mode to Fixed, select NEXT and press OK. The Adjust antenna screen appears. Select

a transponder receivable at your location and adjust the antenna position for maximum signal

strength and quality levels. When the adjustment is completed, choose NEXT and press OK. The

Channel Setup menu will appear.

b) Dish mounted on DiSEqC 1.2 motor

Set Antenna mode to DiSEqC 1.2, choose NEXT and press OK. The menu Adjust antenna will

appear. Select a transponder receivable at your location (choose the Transponder ﬁeld and select a

transponder with t/u). Then choose the Move Dish ﬁeld and adjust the position of the dish with

the t/u buttons. Once the dish is adjusted to the desired position, select Store position and set the

number of the position with the t/u keys. Then choose NEXT and press OK. The Channel Setup

menu will appear.

c) Dish mounted on GOTO X motor

Set Antenna mode to GOTO X, choose NEXT and press OK. The menu Adjust antenna will

appear. Select a transponder receivable at your location (choose the Transponder ﬁeld and select a

transponder with t/u). Then select the ﬁeld My Longitude and enter the value of your longitude

with the numeric keys. Use t/u to select hemisphere East or West. Then select My Latitude and

use the numeric buttons to enter the value of your latitude. Use t/u to select hemisphere North

or South. Select Goto Position and press OK. Your dish will be turned to the position of the satellite.

Select NEXT and press OK. The Channel Setup menu will appear.

Select NEXT and press OK to start the scan. When the scan is completed, the receiver will save the

service information automatically and exits to viewing mode.

PART 1 • English

5.0 MAIN MENU

All important settings and features of your receiver can be operated in the Main Menu. It consists of

the submenus: “Channel Organizer”, “Installation”, “System setting”, “Timer” and “Multimedia”. To

open the MAIN MENU press MENU.

5.1 Channel Organiser

In the MAIN MENU press p/q to move to Channel Organiser and press OK to enter the Channel

Organiser menu. It consists of the submenus “Channel Manager” and “Favourites Manager”.

5.1.1 Channel Manager

You can change the order of the channels, move, delete and edit channels. To change the satellite,

use the RED button.

Sort (GREEN button)

You can sort channels by “Name a~z”, “Name z~a”, “Free-CA”, “Fav–NO Fav” or “Frequency Low-

High”.

Edit (YELLOW button)

Select the channel you want to edit and press YELLOW to move into the modify programme menu

to modify Programme Name, Frequency, Symbol rate, Video PID, Audio PID.

Move channel

Press p/q to highlight the desired channel, press t/u to highlight “Move” and press OK to

conﬁrm the selection of the channel. Use p/q to move the channel to its new location and press

OK to conﬁrm. Repeat this for every channel you want to move.

Delete channel

Press p/q to highlight the desired channel, press t/u to highlight “Del” and press OK to mark

the channel for deletion. Press EXIT and conﬁrm the channel’s deletion by selecting OK and

pressing OK.

Delete all channels

To delete all channels from the current satellite, press BLUE (Del All). You will be asked to conﬁrm

this operation.

5.1.2 Favourites Manager

Press p/q to select the desired channel and t/u to highlight the favourite group. Press OK to

add the selected channel to the favourite group. Repeat this operation to remove the channel from

the favourite list.

5.2 Installation

The Installation menu consists of the submenus “Antenna Installation”, “Auto Scan” and “Manual

Scan”.

5.2.1 Antenna Installation

You can add, edit or delete a satellite in this menu.

Add satellite

Press the RED button. A satellite list will appear. Use t/u to select the desired satellite. If the

desired satellite is not in the list, select NEW SAT1. After the selection of a satellite, the Conﬁgure

Antenna menu will appear. Use this menu to set the LNB Type, LNB Low Freq, LNB High Freq, Band

control, Polarisation control, DiSEqC Switch and Antenna mode. Further steps of the installation

process are described in chapter 4.2.

PART 1 • English

English

Edit satellite

If the parameters of a satellite were changed or if you wish to add a new satellite, you must set the

parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power,

22k Tone, DiSEqC and Antenna Mode. The sequence of editing satellite parameters is the same as

the sequence of “Add satellite” described in chapter 4.2.

Delete satellite

If you want to delete a satellite from the list, press YELLOW. A warning message will appear. Select

OK and press OK to conﬁrm.

5.2.2 Auto Scan

Use GREEN to set the scan mode to Free or Free+Scrambled. If the mode is set to Free, only Free-

to-Air channels will be added to the channel list. If the mode is set to Free+Scrambled, all channels

from the selected satellite will be added.

Press YELLOW to set the Blind Scan to ON or OFF. The Blind scan function is useful when scanning

a newly added satellite. Please note that Blind scan will take more time than the normal scan

process.

Use BLUE to set the scan type to NIT OFF or NIT ON,in case Blind Scan is set to OFF. When Blind

Scan is set to ON you can adjust Quick Search or Detail Search.

Once the setup is completed, press RED to start the scan.

5.2.3 Manual Scan

In Manual Scan you can scan a single transponder, add a new transponder, edit or delete a

transponder. Use the RED button to switch between satellites.

Scan transponder

Use p/q to select the desired transponder. Press OK to start the scan.

Add Transponder

Press GREEN. The Add Transponder submenu will appear.

Frequency: Input the frequency of the new transponder.

Symbol Rate: Input the symbol rate of the new transponder.

Polarity: Select the Polarity of the new transponder.

Edit Transponder

Press YELLOW. The Edit Transponder submenu will appear. This menu is similar to the Add

Transponder menu.

Delete Transponder

Press BLUE to delete a transponder. You will be asked to conﬁrm this operation. Use t/u to select

OK, press OK to conﬁrm.

5.3 System setting

Use this menu to conﬁgure system settings, such as Language Setting, OSD Style, Parental Control,

TV Settings and Time Setting.

5.3.1 Preference

5.3.1.1 Language Setting

Use this option to change the language of the OSD, preferred audio and subtitles.

Use p/q to select OSD language, Audio language or Subtitles language. Press OK or u to enter the

language list and use p/q to select the language. Press OK to conﬁrm.

Other manuals for SRT 6201

Table of contents

Other Strong Receiver manuals

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual