Starview ST2020 Assembly instructions

SSVV

Quality

Digital

Products

www.starview.co.nz

ST2020 - Twin Tuner

NOTE:

Please connect the supplied cable between LNB out (loop) and LNB IN 2

if you wish to use the twin tuner capability of the ST2020

SSVV

Quality

Digital

Products

ST2020 Quick Tips Guide

This receiver has been preloaded and set for the Optus D1 satellite as used by SKY TV and Freeview New Zealand.

All receivers by Starview have been tested working before leaving our CHCH store.

NO TUNING of the ST2020 is required to get the standard Freeview channels as they have been pre-programed for you.

You should be able to connect to a satellite dish aligned to the satellite and start enjoying digital TV.

However there are many settings with satellite TV so this guide has been written to help with the basics.

If you require more advanced information please refer to the other manual supplied with the ST2020, or you may have

to contact your installation technician or supplier.

We know you will enjoy your Starview ST2020.

LNB Frequency's - a quick over view and how to change.

The receiver unit on the end of a satellite dish is called an LNB.

This converts the signal from the satellite to a signal you can send

down coax cable to your satellite receiver.

There are 2 main LNB's used in New Zealand. 11300 & 10750:

The ST2020 has been pre programed for use with the 10750 LNB This

is also the dual or quad LNB’s currently being installed by SKY TV.

Most installations are now using the 10750 LNB ' also called 10.75.

This number is written on most quality LNB's

If you have an older style of LNB it may be a 11300 or 11.3

You will just have to change the LNB setting on the ST2020 to get

signal

NOTE: If you have pictures then you do NOT need to change this

setting.

To change LNB Frequency

Press ‘MENU’ and select the ‘Installation’ menu

Select ‘LNB Configuration’ press ‘OK’

Highlight ‘L.O Frequency’ under LNB 1

Now you can use LEFT & RIGHT to select the correct LNB frequency (fig 3)

Exit to quit and save.

SCANNING FOR NEW CHANNEL'S

To scan for new channels or channel names that may have

changed on the Freeview network.

Press 'MENU' and select the ‘Installation’ menu

Select ‘DVB-S2 Scan press ‘OK’ - under the Optus D1 satellite.

Highlight ‘SAT SCAN FTA ONLY’ then press ‘OK’ button to scan for channels.

When prompted do you want to delete existing -

Press EXIT to leave existing channels in place ( recommended ) or press OK to

delete and start fresh. - The ST2020 will then scan and load channels.

www.starview.co.nz

(fig 1)

(fig 2)

(fig 4)

(fig 5)

(fig 6)

(fig 3)

(fig 5)

(fig 6)

SSVV

Quality

Digital

Products

Time set up

For most of the year this should be set to GMT +12:00

During Daylight savings you should set ‘GMT+13:00’

Press ‘MENU’ and select the ‘System Setup’ menu,

Highlight ‘Time Settings then press ‘OK’

Then you will find the option for GMT

- here you can Change - use the left & right arrows

Press ‘EXIT’ to save.

Note: with GMT usage ON the time is set by the satellite.

After changing the time you may have to power your ST2012 off.

Signal Bars

To get signal & quality bars on your ST2020,

Press ‘INFO’ button on the remote control.

This will bring up the signal and quality bars,

Signal with no quality may indicate you are aligned to the wrong

satellite.

No Signal or Quality , your dish may not be connected correctly.

If you press the ‘YELLOW’ button you will get an audio tone for signal quality.

If you are using the second tuner for recording then you will get signal bars for

both tuners.

Move channel order.

Press ‘MENU’ select ‘Edit Channel List ’ from the main menu.

Use the arrow buttons to locate the channel you wish to move ,

Then press the ‘RED’ button to select SORT function.

Now press ‘BLUE’ button for MANUAL

You will then be asked what number to MOVE TO,

Enter the number here , and repeat pressing the ‘ Blue ‘ button for each channel

you wish to move.

Once done , press ‘EXIT’ to finish

To DELETE a channel ,

Press the ‘BLUE‘ Button to chose DELETE

Then Choose the ‘RED’ Button for DELETE ONE

This will put a RED cross next to the channel, once you have done this for all

channels you wish to delete then press Exit to save ,

you may be asked for the PIN number.

The DEFAULT PIN IS 0786

SSVV

Quality

Digital

Products

VERY IMPORTANT INFORMATION & TIPS

Do NOT connect the receiver to the mains supply until HDMI & Sat leads are connected:

Warranty will be void if installed without good ventilation.

If you connect to an existing dish and have no pictures you may have a 11300 LNB please refer to front of this

guide on how to change this.

After a factory default of the ST2020 you may have to put the channels in your prefered order or scan for changes.

www.starview.co.nz

USB Recording basics.

By using a USB Hard drive you can record Television

We recommend a external powered HDD

Please note some Hard drives work better than others.

We recommend that the Hard drive be for use with the ST2020 only and is

formatted by the ST2020 from the HDD manage menu,.

Record from the EPG

Press EPG ,button this will bring up the program guide , use arrow buttons to

move around the guide

Press the RED button to move within the channel .

Press ‘GREEN ’ button to activate the timer

Once the timer options come up on the screen you can change start & stop

times. or record once / daily , weekly etc press ‘OK’ and you can edit

Press ‘Exit’ when done to save the timer

To Play Back ,

Press ‘HDD’ button on the remote control,

then select the program to watch - then press OK. to start.

The other option is to press FILE button, then you can look for files stored on the

hard drive.

Tips:

You can record one channel and watch another or a recorded file.

if you record 2 channels at the same time you will be unable to watch anything

the screen will go blank.

When selecting a instant record , you may have to wait 15 seconds for the recording

to start, this is due to some Hard drives activating a sleep function.

If you do not have the LOOP cable installed on the back of the ST2020

then you will not be able to record and watch at the same time.

To list your record timers press the Timer button on the remote control

To delete a timer - select the timer and change the mode to OFF.

There are 8 Timer slots for recording.

During play back if you have trouble with Audio lip sync, Please press stop,

then press PLAY again and you should start playing again.

More detail information on recording may be available on the starview website

Table of contents

Other Starview Receiver manuals

Starview

Starview S2828+ Assembly instructions

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual