Speed Queen AES28AWF User manual

Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com.

Keep these instructions for future reference.

(If this machine changes ownership, this manual must accompany machine.)

www.speedqueen.com

Installation Instructions

for Dryers

Dimensions........................................................................ 3

Before You Start................................................................ 4

Installing the Dryer............................................................ 5

Installer Checklist................................................ Back Cover

Date Purchased ________________

Model Number ________________

Serial Number ________________

Part No. 512061R3

June 2007

Inside......................................

The following information applies to the state of Massachusetts, USA.

•This appliance can only be installed by a Massachusetts licensed plumber or gas fitter.

•This appliance must be installed with a 36 inch (91 cm) long flexible gas connector.

•A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance.

•This appliance must not be installed in a bedroom or bathroom.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

– Do not try to light any appliance.

– Do not touch any electrical switch; do not use any phone in your building.

– Clear the room, building or area of all occupants.

– Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

– If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or the gas

supplier.

W052

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of

fire or explosion or to prevent property damage, personal injury or death.

W033

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

W053

WARNING

means without the expressed written consent of the publisher.

512061

Dimensions

DRY2203N

* With leveling legs turned into base.

DRY2203N

23.5 in.

(59.7 cm)

28 in.

(71.1 cm)

0.4 in.

(1.1 cm)

8.0 in.

(20.3 cm)

*4.5 in.

(11.4 cm)

*36in.(91.4cm)

*43 in. (109.2 cm)

*4.0 in.

(10.2 cm)

15.4 in.

(39.1 cm)

26.9 in.

(68.3 cm)

ELECTRIC DRYERS

22.38 in.

(56.85 cm)

*40.25 in. (102.24 cm)

*15.44 in.

(39.2 cm)

DRY2164N

*With leveling legs turned into base.

13/8 in. NPT Gas Connection

DRY2164N

23.5 in.

(59.7 cm) 28 in.

(71.1 cm)

0.4 in.

(1.1 cm)

*4.5 in.

(11.4 cm)

8.0 in.

(20.3 cm)

*36 in. (91.4 cm)

*43 in. (109.2 cm)

*4.0 in.

(10.2 cm)

15.4 in.

(39.1 cm)

26.9 in.

(68.3 cm) *2.8 in.

(7 cm)

2.3 in.

(6 cm) 1

GAS DRYERS

22.38 in.

(56.85 cm)

*40.25 in. (102.24 cm)

*15.44 in. (39.2 cm)

Before You Start

Supplies

For most installations, the basic supplies you will need

are:

Figure 1

Parts Included

An accessories bag has been shipped inside your dryer.

It includes:

•Installation Instructions

•User’s Guide

•Product Registration Card

•Dryer Rack Reply Card

•Warranty Bond

•Three screws (electric dryers only). Refer to

Connecting Power Cord sections in Step 4 of

Installation.

DRY2023N

1Safety Glasses

2Power Cord (Electric Models)

3Wrench

4Screwdriver

5Level

65/16 Inch Socket Wrench

7Duct Tape

8Teflon Tape (Gas Models)

Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person.

W299

WARNING

512061

Installing the Dryer

Step 1: Position and Level the Dryer

Install dryer before washer. This allows room for

attaching exhaust duct.

Select a location with a solid floor. Dryers installed in

residential garages must be elevated 18 inches (46 cm)

above the floor.

No other fuel burning appliance should be installed in

the same closet with the dryer.

The dryer must not be installed or stored in an area

where it will be exposed to water and/or weather.

The dryers needs sufficient clearance and an adequate

air supply for proper operation and ventilation, and for

easier installation and servicing. (Minimum clearances

are shown below).

Figure 2

D823I

1Closet Door

2Centered Air Openings (G) (2 Openings

minimum)

3Outer Wall of Enclosure

**NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting

easier to connect.

2 (G)

**42 in.

(106.7 cm)

AAC

FRONT VIEW

(w/o Closet Door)

SIDE VIEW

(Closet Door)

FRONT VIEW

(Closet Door)

Area Description Free Standing/Alcove

Installation Closet Installation

ADryer sides and rear clearance 0 in. (0 cm) 0 in. (0 cm)

BDryer top clearance 12 in. (30.5 cm) 12 in. (30.5 cm)

CDryer front clearance Not Applicable 2 in. (5.1 cm)

DExhaust duct clearance to

combustible material

2 in. (5.1 cm) 2 in. (5.1 cm)

EWeather hood to ground clearance 12 in. (30.5 cm) 12 in. (30.5 cm)

FDistance from floor or ceiling to

hole edge

Not Applicable 3 in. (7.6 cm)

G* Area of centered air openings in

closet door

Not Applicable 40 sq. in./open (260 sq. cm)

*Louvered door with equivalent air openings is acceptable. (Minimum clearances are shown.)

Place the dryer in position, and adjust the legs until the

dryer is level from side to side and front to back. The

dryer must not rock.

Figure 3

IMPORTANT: In mobile home installations, gas

dryers MUST be permanently attached to the floor

at the time of installation. Order No. 526P3 Dryer

Installation Kit (available at extra cost) for a

manufactured (mobile) home installation. Follow

the instructions supplied with the kit.

Step 2: Connect Dryer Exhaust System

•DO NOT use plastic or thin foil ducting. Rigid

metal duct is recommended.

•Locate dryer so exhaust duct is as short as

possible.

•Be certain old ducts are cleaned before installing

your new dryer.

•Use 4 inch (102 mm) diameter rigid or flexible

metal duct.

•The male end of each section of duct must point

away from the dryer.

•Use as few elbows as possible.

•Use duct tape or pop-rivets on all duct joints.

•Ductwork that runs through unheated areas must

be insulated to help reduce condensation and lint

build-up on pipe walls.

D669I

1Dryer Base

2Level

3Leveling Leg

D669I

D259I

To reduce the risk of fire and combustion

gas accumulation the dryer MUST be

exhausted to the outdoors.

W604

To reduce the risk of fire and the

accumulation of combustion gases, DO NOT

exhaust dryer air into a window well, gas

vent, chimney or enclosed, unventilated

area, such as an attic, wall, ceiling, crawl

space under a building or concealed space

of a building.

W045

WARNING DRY1915N

Figure 4

This gas appliance contains or produces a

chemical or chemicals which can cause

death or serious illness and which are

known to the State of California to cause

cancer, birth defects, or other reproductive

harm. To reduce the risk from substances in

the fuel or from fuel combustion, make sure

this appliance is installed, operated, and

maintained according to the instructions in

this manual.

W115

To reduce the risk of fire, DO NOT use

plastic or thin foil ducting to exhaust the

dryer.

W354

WARNING

DRY1915N

DON’TDO

512061

•In mobile home installations, dryer exhaust duct

must be secured to mobile home structure.

•Dryer exhaust duct MUST NOT terminate under

mobile home.

•Dryer exhausts 220 cfm (measured at back of

dryer).

•Static pressure in exhaust duct should not be

greater than .6 inches water column (1.5 cm),

measured with manometer placed on exhaust

duct two feet (61 cm) from dryer (check with

dryer running and no load).

•Exhausting dryer in hard-to-reach locations can

be done by installing 521P3 Flexible Metal Vent

Kit (available as optional equipment at extra

cost).

•Failure to exhaust dryer properly will void

warranty.

NOTE: Venting materials are not supplied with the

dryer (obtain locally).

Exhaust Direction

The dryer can be exhausted to the outdoors through the

back, left, right or bottom of the dryer. EXCEPTION:

Gas dryers cannot be vented out the left side

because of the burner housing.

Dryer is shipped from factory ready for rear exhaust.

Exhausting the dryer through sides or bottom can be

accomplished by installing a Directional Exhaust Kit,

528P3, available as optional equipment at extra cost.

Exhaust System

For best drying results, recommended maximum

length of exhaust system is shown in Table 1.

To prevent backdraft when dryer is not in operation,

outer end of exhaust pipe must have a weather hood

with hinged dampers (obtain locally).

NOTE: Weather hood should be installed at least

12 inches (30.5 cm) above the ground. Larger

clearances may be necessary for installations where

heavy snowfall can occur.

Tabl e 1

Number of

90° Elbows

Weather Hood Type

Recommended Use Only for Short Run installations

Maximum length of 4 in. (10.2 cm) diameter rigid metal duct.

0 65 feet (19.8 m) 55 feet (16.8 m)

1 55 feet (16.8 m) 47 feet (14.3 m)

2 47 feet (14.3 m) 41 feet (12.5 m)

3 36 feet (11.0 m) 30 feet (9.1 m)

4 28 feet (8.5 m) 22 feet (6.7 m)

Maximum length of 4 in. (10.2 cm) diameter flexible metal duct.

0 45 feet (13.7 m) 35 feet (10.7 m)

1 35 feet (10.7 m) 27 feet (8.2 m)

2 30 feet (9.1 m) 21 feet (6.4 m)

3 25 feet (7.6 m) 17 feet (5.2 m)

420 feet (6.1 m) 15 feet (4.5 m)

NOTE: Deduct 6 feet (1.8 m) for each additional elbow.

4 in.

(10.2 cm)

4 in.

(10.2 cm)

D673I D802I

2-1/2 in.

(6.35 cm)

Step 3: (Gas Dryer Only) Connect Gas

Supply Pipe

1. Make certain your dryer is equipped for use with

the type of gas in your laundry room. Dryer is

equipped at the factory for Natural Gas with a

3/8 inch NPT gas connection.

NOTE: The gas service to a gas dryer must

conform with the local codes and ordinances, or in

the absence of local codes and ordinances, with the

latest edition of the National Fuel Gas Code ANSI

Z223.1/NFPA 54 or the CAN/CGA-B149, National

Gas Installation Code.

Natural Gas, 1000 Btu/ft3(37.3 MJ/m3) service must

be supplied at 6.5 ± 1.5 inch water column pressure.

For proper operation at altitudes above 3000 feet

(915 m) the natural gas valve spud orifice size must be

reduced to ensure complete combustion. Refer to

Table 2.

2. Remove the shipping cap from the gas

connection at the rear of the dryer. Make sure you

do not damage the pipe threads when removing

the cap.

3. Connect to gas supply pipe.

NOTE: When connecting to a gas line, an

equipment shut-off valve must be installed within

6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug

must be installed as shown for checking inlet

pressure. Refer to Figure 5.

To reduce the risk of gas leaks, fire or

explosion:

• The dryer must be connected to the type

of gas as shown on nameplate located in

the door recess.

• Use a new flexible stainless steel

connector.

• Use pipe joint compound insoluble in L.P.

(Liquefied Petroleum) Gas, or Teflon tape,

on all pipe threads.

• Purge air and sediment from gas supply

line before connecting it to the dryer.

Before tightening the connection, purge

remaining air from gas line to dryer until

odor of gas is detected. This step is

required to prevent gas valve

contamination.

• Do not use an open flame to check for gas

leaks. Use a non-corrosive leak detection

fluid.

• Any disassembly requiring the use of

tools must be performed by a suitably

qualified service person.

W316

WARNING

Natural Gas Altitude Adjustments

Altitude Orifice Size Part No.

feet m No. inches mm

3000 915 43 0.0890 2.26 503778

6000 1830 44 0.0860 2.18 58719

8000 2440 45 0.0820 2.08 503779

9000 2740 46 0.0810 2.06 503780

10,000 3050 47 0.0785 1.99 503781

Table 2

D699I

1New stainless steel flexible connector -

(Use design CSA certified connector)

Use only if allowed by local codes

21/8 in. NPT Pipe Plug

3Equipment Shut-Off Valve

4Black Iron Pipe Shorter than 20 ft. (6.1 m) -

Use 3/8 in. (9.5 mm) pipe

53/8 in. NPT Gas Connection

Figure 5

D233I

512061

4. Tighten all connections securely. Turn on gas and

check all pipe connections (internal & external)

for gas leaks with a non-corrosive leak detection

fluid.

NOTE: The dryer and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure testing of that system

at test pressures in excess of 1/2 psi (3.45 kPa).

Refer to Step 9 (Check Heat Source).

L.P. (Liquefied Petroleum) Gas, 2500 Btu/ft3

(93.1 MJ/m3) service must be supplied at 10 ± 1.5 inch

water column pressure.

For proper operation at altitudes above 3000 feet (915 m)

the L.P. gas valve spud orifice size must be reduced to

ensure complete combustion. Refer to Tabl e 3 .

NOTE: DO NOT connect the dryer to L.P. Gas

Service without converting the gas valve. Install

L.P. Gas Conversion Kit 649P3, available at extra

cost.

Step 4: (Electric Dryer Only) Connect

Electrical Plug

Dryer requires 120/240 Volt or 120/208 Volt, 60 Hertz,

3 or 4 wire electrical suppy. Refer to serial plate for

specific electrical requirements.

NOTE: The wiring diagram is located inside the

control hood.

Grounding Information

•This dryer must be connected to a grounded

metal, permanent wiring system; or an

equipment-grounding conductor must be run

with the circuit conductors and connected to the

equipment-grounding terminal or lead on the

dryer.

•The dryer has its own terminal block that must be

connected to a separate branch, 60 Hertz, single

phase circuit, AC (alternating current) circuit,

fused at 30 Amperes (the circuit must be fused

on both sides of the line). Electrical service for

the dryer should be of maximum rated voltage

listed on the nameplate. Do not connect dryer

to 110, 115, or 120 volt circuit.

•Heating elements are available for field

installation in dryers which are to be connected to

electrical service of different voltage than that

listed on nameplate, such as 208 Volt.

•If branch circuit to dryer is 15 feet (4.57 m) or

less in length, No. 10 AWG wire (copper wire

only), or as required by local codes. If over 15

feet (4.57 m), use No. 8 AWG wire (copper wire

only), or as required by local codes. Allow

sufficient slack in wiring so dryer can be moved

from its normal location when necessary.

•The power cord connection between wall

receptacle and dryer terminal block IS NOT

supplied with dryer. Type of power cord and

gauge of wire must conform to local codes.

L.P. Altitude Adjustments

Altitude Orifice Size Part No.

feet m No. inches mm

3000 915 55 0.0520 1.32 58755

8000 2440 56 0.0465 1.18 503786

Table 3

To reduce the risk of fire, electric shock,

serious injury or death, all wiring and

grounding MUST conform with the latest

edition of the National Electrical Code,

ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1, and such local

regulations as might apply. It is the

customer’s responsibility to have the wiring

and fuses installed by a qualified electrician

to make sure adequate electrical power is

available to the dryer.

W521

WARNING

Connecting Power Cord with Three-Wire Plug

NOTE: Four-wire cord is required for mobile

homes or where codes do not permit grounding

through neutral.

Figure 6

1. Disconnect power to dryer.

2. Remove access cover from rear of dryer.

Figure 7

3. Use a strain relief and insert end of power cord

through power supply hole.

Figure 8

D816I

13 Wire Grounded Neutral 120/240 Volt, 60 Hertz

AC 1 Phase Service Entrance Switch Box

(Refer to NOTE above)

4Metallic or Non-Metallic Sheathed Cable

(Copper Wire Only)

5Power Cord (Not supplied with dryer)

230 Ampere Fuses or Circuit Breaker 6Neutral

3Neutral Wire 7Terminal Block in Dryer

NOTE: The power cord is NOT supplied with the

electric dryer. Type of power cord and gauge of wire

must conform to local codes and instructions.

The method of wiring the dryer is optional and subject

to local code requirements.

NOTE: Connect the dryer to the power supply with the

MAXIMUM RATED VOLTAGE listed on the nameplate.

POWER CORD CONNECTION DIRECT CONNECTION

L1 L2 L1 L2

INTERMEDIATE

SHUT-OFF BOX

(may or may not

be fused)

POWER SUPPLYPOWER SUPPLY

INTERMEDIATE

FUSE BOX (may

be omitted if

service entrance

box is fused)

WALL

RECEPTACLE

A typical

30-Amp

Three-Wire

Receptacle

NEMA Type

10-30R

120 ± 12

V.A.C.

120 ± 12

V. A . C .

240 ± 12

V.A.C.

NOTE: Use COPPER WIRE only.

Shorter than 15 ft. (4.5 m) – use 10 AWG

Longer than 15 ft. (4.5 m) – use 8 AWG

D695I

D696I

This manual suits for next models

Table of contents

Other Speed Queen Dryer manuals

Speed Queen

Speed Queen Stack Tumble Dryers User manual

Speed Queen

Speed Queen SDEY07WF1500 User manual

Speed Queen

Speed Queen FES17AWF1500 User manual

Speed Queen

Speed Queen DE3270 User manual

Speed Queen

Speed Queen AEM433 User manual

Speed Queen

Speed Queen STT30 User manual

Speed Queen

Speed Queen Speed Queen User manual

Speed Queen

Speed Queen ST025 User manual

Speed Queen

Speed Queen Tumbler 55 lb User manual

Speed Queen

Speed Queen VENDED ST050 User manual

Speed Queen

Speed Queen LES33 User manual

Speed Queen

Speed Queen HE5003 User manual

Speed Queen

Speed Queen HE6350 User manual

Speed Queen

Speed Queen ADE3TR User manual

Speed Queen

Speed Queen DR7003WG User manual

Speed Queen

Speed Queen DE1020 User manual

Speed Queen

Speed Queen HE4430 User manual

Speed Queen

Speed Queen ADE41F User manual

Speed Queen

Speed Queen HE4030 User manual

Speed Queen

Speed Queen KES17AWF1500 User manual

Speed Queen

Speed Queen AM07-502 User manual

Speed Queen

Speed Queen ST025 User manual

Speed Queen

Speed Queen 55322R1 User manual

Speed Queen

Speed Queen Dryer User manual

Popular Dryer manuals by other brands

Bosch

Bosch WTA79200GB Installation and operating instructions

Amana

Amana W10233410A Use and care guide

Miele

Miele TWH 780 WP operating instructions

Asko

Asko T760 user guide

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Original instructions

Bosch

Bosch Logixx 10 WTB76556GB Instruction manual and installation instructions

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Operation and installation

Electrolux

Electrolux EW2H328R2 user manual

Beko

Beko DS8433RX1M user manual

Dawlance

Dawlance Spinner DS 6000 C owner's manual

Electrolux

Electrolux TP5080TW user manual

AEG

AEG TR838P4OB user manual

Indesit

Indesit IDV 75 instruction manual

Infiniton

Infiniton SD-DG85C manual

BOMANN

BOMANN WT 5019 instruction manual

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Installation

Asko

Asko T793C operating instructions

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer installation instructions