Speco CVC-647TP User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Vicon

Vicon V662-D-1 Installation and operation guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

P. 1

CVC-647TP

Vandal Resistant Dome

Camera Instructions

CONTENTS

Page Page

1. DESCRIPTION……… ........ 1

2. INSTALLATION………….... 2

3.WIRING INSTRUCTIONS ... 3

4. SPECIFICATIONS.............. 4

1. DESCRIPTION

Thank you very much for purchasing our product.

This Tamper Resistant Color Dome Camera uses a SONY Super-HAD

CCD Image Sensor and solid-state circuitry, which provides long life and

high reliability. This CVC-647TP offers excellent image quality with low

lag and high burn resistance, and is not subject to distortions from

magnetic fields. Highly resistant to shock and vibration, and easy to install,

this Camera is a very good choice for your CCTV system.

P. 2

2. INSTALLATION

STEP 1: Please select the most suitable position on the ceiling to install

the camera.

STEP 2: Remove the locking screw and rotate the dome housing

counterclockwise to remove it from the mounting base (as shown

by the figure below).

Mount i ng Base

DOME Ho u s i ng

OR

STEP 3: Hold the mounting base against the ceiling and center it over the

cable hole. Attach to the ceiling using the four screws supplied in

the accessory package (shown by the figure below).

Then allow the cable connectors to pass through the cable entry

hole made available for that purpose (shown by figure below).

STEP 4: Set the proper image angle by adjusting the camera body.

When the camera angle adjustment has been completed, rotate the

dome housing clockwise to secure it to the mounting base.

STEP 5: Lock the dome cover into position using the Locking screw.

3. WIRING INSTRUCTIONS

STEP 1: Connect a coaxial cable between the camera and the monitor

using a 75-Ohm coaxial cable with 95% copper shielding.

STEP 2: Plug the Power Adapter into an AC socket and the DC plug into

the DC Jack of the camera. Please note that the center pin is

positive (+).

TO MONI T OR

TO DC POWER SOURCE

P. 3

.

4. SPECIFICATIONS

Camera Type Color High Resolution

Image Pick-up Device SONY 1/4” Super-HAD CCD sensor

Effective Picture

Elements (HxV) NTSC: 510x492

Horizontal Resolution 380 TV lines

Minimum Illumination 0.5 LUX @ F2.0

S/N Ratio More than 50 dB

Auto Electronic Shutter NTSC: 1/60s~1/100,000 sec

Gamma Characteristic 0.45

Lens Furnished Board lens f 3.6mm / F 2.0

(Optional: f 2.5 / 4.3 / 6.0 / 8.0 / 12 /mm)

Auto Gain Control Yes

Auto White Balance Yes

Synchronous System Negative sync. Internal.

Video Output 1 Vp-p / 75 Ohms. (BNC Connector

Power Supply UL/CSA 12-Volt DC Regulated Supply included

Power Consumption 120 mA

Operating Temp. -10℃to 50℃(14℉to 122℉)

Note: Design and specifications are subject to change without prior notice.

Speco Technologies

200 New Highway

Amityville, NY 11701

Tel: 631-957-8700

Fax: 631-957-9142

www.specotech.com

2003/11/03 040024B by SPECO Technology

P. 4