Sonoff 4CH User manual

中文---------------- 1- 4 English--------------5-8

Deutsch-----------9-12 Español-----------13-16

Français----------17- 20 Italiano------------21-24

Русский язык----25-28

4CHR3: 4-gang Wi-Fi Smart Switch

4CHPROR3: 4-gang Wi-Fi Smart Switch with RF Control

4CH/4CHPRO

User manual V 1.0

产品参数

产品型号 4CHR3/4CHPROR3

最大负载

输入

Wi-Fi IEEE 802.11 b/g/n 2.4GHz

Wi-Fi指示灯状态说明

Wi-Fi指示灯状态状态描述

常亮设备已连接

快闪一下

快闪两下

两短一长闪烁

找不到路由

连接上路由，但没连上外网

配网模式

快闪三下升级中

中文中文中文

SONOFF TECHNOLOGIES CO., LTD.

4CHR3: 10A/2200W/通道 16A/3500W/总负载

4CHPROR3: 10A/2200W/通道 40A/8800W/总负载

输出

RF 433.92MHz

4CHR3不支持433.92MHz遥控功能。

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

145x90x34mm

支持平台 (Android 4.1 & iOS 9.0) 或者更高版本

产品材料

产品规格

连续快闪兼容模式

产品介绍

中文中文中文

SONOFF TECHNOLOGIES CO., LTD.

（L1/ L2/L3 /L4）

手动开关/配置按钮

（L1/ L2/L3 /L4）

开关指示灯(红色)

Wi-Fi信号指示灯(蓝色)

DC 输入

AC 输入常开常闭

公共

COM

（R1/ R2/R3/R4）

手动开关/配置按钮

（R1/ R2/R3/R4）

开关指示灯(红色)

Wi-Fi信号指示灯(蓝色)

4CHR3

4CHPROR3

产品特点

4CHR3/4CHPROR3是一款支持互锁/自锁/点动3种工作模式相互切换的四通道智能开

关。可随时随地通过手机远程打开或关闭家里的设备，设置定时开关、分享给您的家人

一起控制等等。

远程控制智能定时语音控制分享控制

433MHz控制

局域网模式

场景联动添加摄像头

上电状态设置

互锁模式点动模式

自锁模式

中文中文中文

SONOFF TECHNOLOGIES CO., LTD.

RF(遥控)配对

4CHPROR3支持使用 433.92MHz 遥控器控制开关，每通道可独立学习遥

控器按键，此功能属于本地近程无线遥控与Wi-Fi网络无关。

学习配对遥控器方法：

清除遥控器配对方法：

长按将要清除配对的通道开关键5秒直到Wi-Fi指示灯呈红色“快闪两下”,

松开，然后短按遥控器任意按键，Wi-Fi指示灯呈红色“快闪一下”则表示

清码完成。其它按键按照此方法清码即可。

长按将要配对的通道开关键3秒直到Wi-Fi指示灯呈红色“快闪一下”, 松开，

然后短按遥控器上要配对的按键，Wi-Fi指示灯呈红色再次 “快闪一下”则

表示配对成功。其它按键按照此方法重复学习配对即可.

兼容模式

如使用快速模式配网失败，请使用“兼容模式”进行配对。

1. 长按任意配置按钮5秒直到Wi-Fi指示灯呈“两短一长闪烁”状态，松开。

　再次长按任意配置按钮5秒直到Wi-Fi指示灯呈“快闪”状态，此时设备进

　入兼容模式。

2. 在app界面，点击“+”，选择“兼容模式”。

And roid设备：

只需输入Wi-Fi密码，点击等待配对完成。

iOS设备：

先把移动设备连接上Wi-Fi账号为：ITEAD-******，密码为：12345678，

然后回到“易微联”app，点击下一步，等待配对完成。

长按任意配置按钮5秒直到Wi-Fi指示灯呈“两短一长闪烁”再松开，此时设备重置成

功，默认进入快速配网模式。

更换新的网络环境使用时，需要恢复出厂设置，再重新进行网络连接。

恢复出厂设置

常见问题

中文中文中文

SONOFF TECHNOLOGIES CO., LTD.

2 . 蓝灯1秒快闪两下：说明设备已连接到了Wi -Fi但没有连上外网。

问：设备添加成功后，显示离线，无法控制？

答：设备刚添加成功后，需要1-2分钟时间连接您的路由器并连网。如果长时间还是

显示不在线，请根据Wi-Fi指示灯的状态来判断：

1. 蓝灯1秒快闪一下：说明设备没有连上您的Wi-Fi。

① 可能是Wi-Fi密码输入不正确.

② 可能是设备离您的路由器太远，信号太弱，或环境有干扰。请先将设备靠近路由

器，如无改善，重新添加一遍.

③ 设备不能识别5G的Wi-Fi，请选择2.4G的Wi-Fi重新添加.

④ 检查您的路由器后台是否开启MAC地址过滤，如有，请关闭。

如果以上均尝试不能解决，请用一部手机开启个人热点，尝试重新添加。

请确认您的Wi-Fi当前连接外网是否稳定、正常。如时好时坏，频繁出现双闪情况，

说明您的网络不稳定，并非产品原因，如网络正常，请断电进行重启。

SONOFF TECHNOLOGIES CO., LTD.

Specifications

Device is connected successfully

Unable to discover the router

Upgrading

Quick Pairing Mode

English

Connect to the router but fail to connect to Wi-Fi

4CHR3/4CHPROR3

Max. Load

Wi-Fi IEEE 802.11 b/g/n 2.4GHz

Wi-Fi LED indicator status instruction

4CHR3: 10A/2200W/Gang 16A/3500W/Total

4CHPROR3: 10A/2200W/Gang 40A/8800W/Total

RF 433.92MHz

4CHR3 does not support the remote controller with 433.92MHz.

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

145x90x34mm

Flashes quickly

Model

Input

Output

(Android 4.1 & iOS 9.0) or higherOperating systems

Material

Dimension

Status instruction

Wi-Fi LED indicator status

Flashes (one long and two short)

Keeps on

Flashes quickly once

Flashes quickly three times

Flashes quickly twice

Compatible Pairing Mode

SONOFF TECHNOLOGIES CO., LTD. English

Product Introduction

Wi-Fi LED indicator(Blue)

（L1/L2/L3/L4）

Pairing button/Manual switch

（L1/L2/L3 /L4）

On/Oﬀ LED indicator(Red)

（R1/R2/R3/R4）

Pairing button/Manual switch

（R1/ R2/R3/R4）

On/Oﬀ LED indicator(Red)

Wi-Fi LED indicator(Blue)

DC input AC input

4CHR3

4CHPROR3

Features

Camera FeaturePower-on State

Remote Control Single/Countdown Timing Voice Control Share Control

LAN Control

Smart Scene

Self-locking Interlock Inching

433MHz Remote Control

4CHR3/4CHPROR3 is a 4-gang Wi-Fi smart switch with self-locking, interlock and

inching that allow you to remotely turn on/oﬀ connected devices via your smartphone,

schedule on or oﬀ, share to your family to control together.

SONOFF TECHNOLOGIES CO., LTD. English

RF Remote Controller Pairing

The 4CHPROR3 supports the remote controller with 433.92MHz frequency brand to

turn on/oﬀ, and each channel can learn it independently, which is local short-range

wireless control not Wi-Fi control.

Pairing Method:

Clearing Method:

Long press the channel switch button to be paired for 3s until the Wi-Fi LED indicator

turns red and "quickly ﬂashes once" and release, then short press the button to be

paired on the remote control. If the Wi-Fi LED indicator turns red and "quickly ﬂashes

once", it indicates that the pairing is successful.

Long pr ess th e channel swi tch bu tton to be cle ared f or 5s until the Wi-F i LED

indicator turns red and "quickly ﬂashes twice" and release, then short press the

button to be cleared on the remote control. If the Wi-Fi LED indicator turns red and

"quickly ﬂashes once", it indicates that the code is cleared.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode, please try “Compatible Pairing Mode ” to pair.

1. Long press any conﬁguration button for 5s until the Wi-Fi LED indicator changes

in a cycle of two short ﬂashes and one long ﬂash and release. Long press any

conﬁguration button for 5s again until the Wi-Fi LED indicator ﬂashes quickly.

Then, the device enters Compatible Pairing Mode .

2.Tap “+” and select “Compatible Pairing Mode ” on APP.

For Android system:

Enter Wi-Fi password and tap “Next”. Be patient until pairing completes.

For iOS system:

Select Wi-Fi SSID with ITEAD-****** and enter the password 12345678, and then

go back to eWeLink APP and tap “Next”. Be patient until pairing completes.

SONOFF TECHNOLOGIES CO., LTD. English

Long press the pairing button for about 5s until the Wi-Fi LED indicator changes in

a cycle of two short and one long ﬂash and release, then the reset is successful.

The device enters Quick Pairing Mode.

Factory Reset

Please reset the switch to factory defaults if you want to change the Wi-Fi network,

then reconnect the new network.

Q: Why my device stays “Oﬄine”?

A: The newly added device needs 1 – 2mins to connect Wi-Fi and network. If it

stays oﬄine for a long time , p lease judge the se problems by the blue Wi-Fi

indicator status:

1. The blue Wi-Fi indicator quickly ﬂashes once per second, which means that the

switch failed to connect your Wi-Fi:

① Maybe you have entered a wrong Wi-Fi password.

② Maybe there's too much distance between the switch your router or the

environment causes interference, consider getting close to the router. If failed,

please add it again.

③ The 5G Wi-Fi network is not supported and only supports the 2.4GHz wireless

network.

④ Maybe the MAC address ﬁltering is open. Please turn it oﬀ.

2. Blue indicator quickly ﬂashes twice per second, which means your device has

connected to Wi-Fi but failed to connect to the server.

If none of the above methods solved the problem, you can open the mobile

datanetwork on your phone to create a Wi-Fi hotspot, then add the device again.

Ensure steady enough network. If double ﬂash occurs frequently, which means you access

an unsteady network, not a product problem. If the network is normal, try to turn oﬀ

the power to restart the switch.

Common Problems

SONOFF TECHNOLOGIES CO., LTD. Deutsch

Technische Daten

(Android 4.1 und iOS 9.0) oder höher

Wi-Fi LED-Anzeige Statusanzeige Anweisung

Gerät ist erfolgreich verbunden

Der Router konnte nicht gefunden werden

Erfolgreiche Verbindung zum Router, aber

Wi-Fi ist nicht verbunden

Schnellkopplungsmodus

Aktualisierung

Blinkt (einmal lang und zweimal

kurz)

4CHR3/4CHPROR3

IEEE 802.11 b/g/n 2.4GHz

4CHR3: 10A/2200W/Einzelschalter 16A/3500W/Alle Schalter

4CHPROR3: 10A/2200W/Einzelschalter 40A/8800W/Alle Schalter

433.92MHz

4CHR3 unterstützt keine Fernbedienung mit433,92 MHz.

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

4CHR3: 100-240V AC 50/60Hz

4CHPROR3: 100-240V AC 50/60Hz (DC: 9-23V)

145x90x34mm

Schnell blinkt

Status-Anweisung

Wi-Fi LED-Anzeige Status

Ist immer an

Blinkt einmal schnell

Betriebssysteme

Abmessungen

Materialien

Ausgang

Modell

Eingang

WLAN-Standard

Blinkt zweimal schnell

Blinkt dreimal schnell

Kompatibler Kopplungsmodus

Max. Belastung

Other manuals for 4CH

This manual suits for next models

Table of contents

Languages:

Other Sonoff Switch manuals

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual