Sloan EAF-700 Manual

INSTALLATION INST UCTIONS AND USE MANUAL FO

SLOAN®EAF GOOSENECK SE IES FAUCETS

Code No: 0816409

Rev. 1 (07/11)

LIMITED WA ANTY

Unless otherwise noted, Sloan Valve Company warrants its product, manufactured and sold for commercial for industrial uses, to be free from defects in material and

workmanship for a period of three (3) years (one (1) year for special nishes, SF faucets, PWT electronics and 30 days for PWT software) from date of rst purchase.

During this period, Sloan Valve Compnay will, at its option repair replace, or refund the purchase price of any product which fails to conform with this warranty under

normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No

claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products

directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE CO PANY RESPONSIBLE FOR ANY CONSEQUENTIAL DA AGES

OF ANY EASURE WHATSOEVER.

P IO TO INSTALLATION

Prior to installing the Sloan Optima EAF-700 Series Faucets,

install the items listed below. Also, refer to rough-in illustrations.

• Lavatory/sink

• Drain Line

• Hot/Cold Water Supply Lines or Tempered Supply

I PORTANT:

• ALL PLU BING SHOULD BE INSTALLED IN ACCORDANCE WITH

APPLICABLE CODES AND REGULATIONS.

• FLUSH ALL WATER LINES PRIOR TO AKING CONNECTIONS.

• KEEP THREAD SEALANT OUT OF YOUR WATERWAY TO PREVENT

CO PONENT PART DA AGE! DO NOT USE ANY SEALANT ON

CO PRESSION FITTINGS.

Trim Plates

When the EAF Faucet is installed on a sink that has three (3) hole

punchings, a trim plate should be used. Trim Plates must be specied and

ordered separately.

SFP-11 Trim Plate for 4” (102 mm) Centerset Sink

SFP-22 Trim Plate for 8” (203 mm) Centerset Sink

TOOLS EQUI ED FO INSTALLATION

• 13 mm open end wrench or nut driver for faucet retainer nut • 5/8” open end wrench for female end of ex hose

EAF-700

AC Powered, Sensor Activated Electronic

Gooseneck Hand Washing Faucets

EAF-750

Battery Powered, Sensor Activated Electronic

Gooseneck Hand Washing Faucets

1 - INSTALLATION TO DECK

Remove nut, faucet retainer and gasket.

Install faucet into the center hole in deck or lavatory – 1-3/16”

(30 mm) minimum hole required.

NOTE: If installing the faucet on a three (3) hole sink, a trim plate

should be installed at this time.

I PORTANT: FLUSH DIRT, DEBRIS, AND SEDI ENT FRO SUPPLY LINE(S)

BEFORE CONNECTING FLEX HOSE(S).

FAUCET OUGH-IN

odel EAF-700/750

1.5 gpm (5.7 Lpm) ax. Flow†

Faucets with Hot/Cold Water Supply

odel EAF-700/750

1.5 gpm (5.7 Lpm) ax. Flow†

Faucets with Tempered Water Supply

24°

5-7/8”

(147 mm)

SPOUT

O-RING

MIXING LEVER

(CAN BE SET AND

REMOVED)

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

HOT

SUPPLY

COLD

SUPPLY

13” (330 mm)

LONG FLEX HOSE

2-1/4” (57 mm) 2-9/16”

(65 mm)

TEMPERED

SUPPLY

SPOUT

O-RING

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

13” (330 mm)

LONG FLEX HOSE

5-11/32”

(151 mm)

3-15/16”

(100 mm)

10-1/32”

(255 mm)

24°

5-7/8”

(147 mm)

SPOUT

O-RING

MIXING LEVER

(CAN BE SET AND

REMOVED)

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

HOT

SUPPLY

COLD

SUPPLY

13” (330 mm)

LONG FLEX HOSE

2-1/4” (57 mm) 2-9/16”

(65 mm)

TEMPERED

SUPPLY

SPOUT

O-RING

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

13” (330 mm)

LONG FLEX HOSE

5-11/32”

(151 mm)

3-15/16”

(100 mm)

10-1/32”

(255 mm)

24°

5-7/8”

(147 mm)

SPOUT

O-RING

MIXING LEVER

(CAN BE SET AND

REMOVED)

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

HOT

SUPPLY

COLD

SUPPLY

13” (330 mm)

LONG FLEX HOSE

2-1/4” (57 mm) 2-9/16”

(65 mm)

TEMPERED

SUPPLY

SPOUT

O-RING

1-3/16” (30 mm)

MIN. DIA. HOLE

REQUIRED

1-1/2” (38 mm)

MAX. DECK

THICKNESS

NUT

RETAINER

GASKET

13” (330 mm)

LONG FLEX HOSE

5-11/32”

(151 mm)

3-15/16”

(100 mm)

10-1/32”

(255 mm)

If a connection to separate

hot and cold water supplies

is desired, then a Bak-Chek®

tee tting (not supplied) must

be used prior to connecting

to the faucet.

When the EAF faucet is installed on a sink that has three

(3) hole punchings, a trim plate should be used. Trim plate

must be specied and ordered separately:

ETF-312-A

Trim Plate for 4” (102 mm) Centerset Sink

ETF-510-A

Trim Plate for 8” (204 mm) Centerset Sink

† EAF Faucets are furnished with a 1.5 gpm (3.8 Lpm) spray head).

6”

(152 mm)

CABLE

LENGTH

FROM FAUCET

BATTERY

PACK

Ø 2-13/32”

(61 mm)

3A -

EAF-700 MODELS

– PLUG ADAPTE INTO ECEPTACLE

3B -

EAF-750 MODELS

– CONNECT BATTE Y PACK

2 - CONNECTION TO WATE SUPPLY

Open supply stop(s).

Flush supply stops before making connections. Tighten the ex hose (with strainer in place) securely to the

supply.

Install strainer and ex hose onto supply stop.

ELECTRICAL CONNECTION FOR UP TO SIX (6) FAUCETS

USING ONE ADAPTER

6 VDC

PLUG-IN

ADAPTER

LI IT ONE FAUCET PER BATTERY PACK

POWER SPLITTER

ELECTRICAL CABLE

POWER SPLITTER

ELECTRICAL CABLE

TO ADDITIONAL

FAUCETS

(6 AX.)

SET AND FIX TEMPE ATU E (OPTIONAL)

4 - STA T-UP

Activate faucet by pressing the button one (1) time, then

immediately step away.

Faucet will run water for 4 seconds. Wait 10 seconds and then the

faucet is ready to use.

Remove label from faucet sensor.

HOT LIMIT STOP ADJUSTMENT

LI IT THE AXI U WATER TE PERATURE. NOTE: THIS DOES NOT TAKE THE PLACE OF AN ASSE 1070 CERTIFIED IXING DEVICE. BUT IS AN ADDED

EASURE TO LI IT DELIVERY OF HOT WATER.

SENSO ANGE ADJUSTMENT

FACTORY SETTING IS APPROPRIATE FOR THE AJORITY OF APPLICATIONS AND SHOULD NOT REQUIRE RESETTING UNLESS UNDER EXTRE E SITUATIONS.

5 Sec.

2x +

1x5 Sec.

FACTORY DEFAULT = 6

1 x ( 1x, 2x,...,5x)

12/24 LINE PU GE FEATU E

I.Q.-CLICK FEATU E

1x 24 sec

DEACTIVATE

ACTIVATE 2x

12h

---

24h

1 x

2 x

2 min.

1 x 2 Sec.

2 min.

1 x

2 x

2 min.

1 x 2 Sec.

2 min.

1 x

2 x

2 min.

1 x 2 Sec.

2 min.

1 x

2 x

2 min.

1 x 2 Sec.

2 min.

1 x 6 Sec.

1 x 1 x 0-5 Sec. 1x

1 x 6 Sec.

1 x 1 x 0-5 Sec. 1x

1 x 6 Sec.

1 x 1 x 0-5 Sec. 1x

OFF-DELAY (FOLLOW UP TIME)

Press the button for

approximately six (6)

seconds. Release.

Continuous run of water for

2 minutes.

Pause faucet for cleaning for

2 minutes.

AFaucet will operate normally after 2 minutes or after pressing

i.q.-click button once.

Faucet will operate normally after 2 minutes or after pressing

i.q.-click button once.

Press again (water

ows) and release

when the desired

time of water ow

(0-5 seconds) is

reached.

Sensor will ash once

and then the faucet is

ready to operate.

I. CONTINUOUS UN

II. CLEANING MODE

DURATION OF TI E THE WATER RUNS AFTER TARGET IS RE OVED.

This feature will operate the faucet every

12 or 24 hours since last use, if not used

to prevent stagnant water conditions.

Default purge duration is two minutes.

Consult factory regarding other timing

options.

OPE ATION

As the user’s hands enter the beam’s effective range, the beam is reected

back into the sensor receiver and activates the solenoid valve allowing

water to ow from the faucet. Water will ow until the hands of the user

are removed or until the faucet reaches its automatic time out limit setting.

BATTE Y EPLACEMENT

No need to turn

off water.

Loosen screw

with hex wrench

and remove cap.

Slide cover

forward and lift

off.

Remove battery.

Replace batteries

with new “CR-P2”

lithium battery.

Replace cover.

Activate faucet

by pressing i.q.

cliq one (1) time,

then immediately

step away.

Faucet will

operate for 4

seconds.

Wait 10 seconds

and then the

faucet is ready

for operation.

NOTE: REPLACE BATTERY WHEN RED LED INDICATOR FLASHES EACH TI E FAUCET IS IN USE OR WHEN FAUCET STOPS FUNCTIONING.

0 V 6 V

T OUBLESHOOTING

1. Faucet does not function.

A. Adhesive packaging label afxed over sensor eye.

Remove adhesive label from sensor eye.

B. “Intermittent Off” is activated.

Press button once.

C. Water supply stop(s) closed.

Open water supply stop(s).

D. Battery is “dead”.

Replace battery (refer to Battery Replacement section of guide).

2. Faucet delivers water in an uncontrolled manner.

A. Reection.

Remove reective surface.

B. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

3. Faucet does not deliver any water when Sensor is activated.

Solenoid Valve produces an audible “CLICK.”

A. Water supply stop(s) closed.

Open water supply stop(s).

B. Water supply stop strainer(s) clogged.

Remove, clean, and reinstall water supply stop strainer(s). Replace

strainer(s), if required.

Solenoid Valve DOES NOT produce an audible “CLICK.”

A. Battery low (battery operated models).

Replace battery (refer to Battery Replacement section of guide).

B. Power failure.

Check power supply.

4. Faucet delivers only a slow ow or dribble when sensor is activated.

A. Water supply stop(s) are partially closed.

Completely open water supply stop(s).

B. Water supply stop strainer(s) clogged.

Remove, clean, and reinstall water supply stop strainer(s). Replace

strainer(s), if required.

C. Spray head is clogged.

Remove, clean, and reinstall spray head. Replace spray head,

if required.

D. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

5. Faucet does not stop delivering water or contrinues to drip after user is

no longer detected.

A. Faucet is not working properly.

Contact Sloan Valve Company Installation Engineering Department.

6. LED indicator blinks when faucet is in use.

A. Battery low (battery operated models).

Replace battery (refer to Battery Replacement section of guide).

7. The water temperature is too hot or too cold on a faucet connected to

hot and cold supply lines.

A. Supply stops are not adjusted properly.

Adjust supply stops.

When assistance is required, please contact Sloan’s

Installation Engineering Department at:

1-888-SLOAN-14 (1-888-756-2614)

CA E AND CLEANING

DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to

clean faucets that may dull the luster and attack the chrome or special

decorative nishes. Use ONLY mild soap and water, then wipe dry with

clean cloth or towel. While cleaning the bathroom sink, protect the faucet

from any splattering of cleaner. Acids and cleaning uids will discolor or

remove chrome plating.

TECHNICAL DATA

NO INAL VOLTAGE

POWER SUPPLY

WATER PRESSURE

FLOW RATE

WATER FLOW DURATION

WATER TE PERATURE

6 VDC

120 VAC/ 6.75 VDC

4.3-125 PSI (0.3 - 8.6 bar)

1.5 gpm (5.7 Lpm)

0.5-4 seconds

AX. 176°F/80°C

PA TS LIST

SLOAN VALVE COMPANY • 10500 SEYMOU AVENUE • F ANKLIN PA K, IL 60133

Phone: 1-800-9-VALVE-9 (1-800-982-5839) • Fax: 1-800-447-8329 • www.sloanvalve.com

The information contained in this document is subject to change without notice.

Item Part

No. No. Description

1 –– Spout Assembly

2 –– Integral Side ixer Handle Cap

3–– Integral Side ixer Kit

4 EAF-2 Solenoid

5 –– Sensor Assembly

6 EAF-1 ounting Hardware

7 EAF-44 Power Splitter

8 EAF-24-A 11-13/16” (300 mm) Extension Cable

EAF-25-A 47-1/4” (1200 mm) Extension Cable

EAF-17-A 126” (3200 mm) Extension Cable

9 EAF-1008 13” (330 mm) Flexible Supply Hose

10 EAF-9 Filter/Strainer

11 EAF-48 Battery Box

12 EAF-11-A Plug-in Voltage Adapter, US Plug

11 12

This manual suits for next models

Table of contents

Other Sloan Plumbing Product manuals

Sloan

Sloan Act-O-Matic Showerhead AC-11-1.8 Use and care manual

Sloan

Sloan 0344067 Use and care manual

Sloan

Sloan TRUFLUSH TRF 8036 User manual

Sloan

Sloan REGAL XL series User manual

Sloan

Sloan EFP-39-A User manual

Sloan

Sloan OPTIMA plus Series User manual

Sloan

Sloan 150 ES-SM User manual

Sloan

Sloan FLUSHMATE III 503 Series Application guide

Sloan

Sloan SF-2100 Operating manual

Sloan

Sloan EL-485-A User manual

Sloan

Sloan TruFlush TRF 8936-CP User manual

Sloan

Sloan Optima ETF-600 User manual

Sloan

Sloan Waterfree WES-150 Guide

Sloan

Sloan BASYS EFX-8 Use and care manual

Sloan

Sloan CX 158 User manual

Sloan

Sloan ESD601A User manual

Sloan

Sloan TRF 156-1.1 User manual

Sloan

Sloan OPTIMA I.Q. EAF-150 Series User manual

Sloan

Sloan Optima ETF-600 User manual

Sloan

Sloan Optima EBF-550 Use and care manual

Sloan

Sloan ECOS HET 8100 Series User manual

Sloan

Sloan ESD Series User manual

Sloan

Sloan AER-DEC 81000 Use and care manual

Sloan

Sloan ESS-2000 Series User manual

Popular Plumbing Product manuals by other brands

Weka

Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS

Kohler

Kohler K-6228 Installation and care guide

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Operator's manual

American Standard

American Standard DetectLink 6072121 manual

Uponor

Uponor Contec TS Mounting instructions

Pfister

Pfister Selia 49-SL Quick installation guide

Fortis

Fortis VITRINA 6068700 quick start guide

Fortis

Fortis MILANO 78211JS installation instructions

Kohler

Kohler K-12183 Homeowner's guide

Maxxus

Maxxus MX-M206-01 instruction manual

Moen

Moen 5922 Series installation instructions

Viega

Viega Prevista Pure 8512 Instructions for use

Kohler

Kohler Centerset K-15240 Homeowner's guide

Viega

Viega Prevista Dry 8522.33 Instructions for use

Sanela

Sanela Lema SLP 59RB Instructions for use

Elkay

Elkay EDF15AC Installation, care & use manual

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions

baliv

baliv WT-140 manual