Siemens RWD62U Owner's manual

RWD62U

Technical Instructions

Document No. 155-737

January 14, 2005

Universal Controller

Description The Universal controller is intended for heating, air conditioning, ventilation and

refrigeration in comfort control applications. RWD62U main loop control applications

are designed for temperature, static pressure, humidity, air pressure, fluid pressure,

refrigeration, air quality and air fluid velocity control. The controller contains pre-

programmed applications.

Auxiliary control functions include:

• Day/night setpoints

• Remote setpoint control

• Limiter control

• Cascade control

• Maximum priority

• Setpoint compensation

• Summer/winter operation

Control parameters are adjusted for maximum comfort control via three buttons on the

face of the device, or with a laptop computer and Siemens Building Technologies

program software.

NOTE: For complete supporting technical documentation, including training

presentations, see www.us.sbt.siemens.com/hvp/components.

Features • Stand-alone electronic temperature controller with P or P+I response

• 24 Vac operating voltage

• Control application selectable via Application Number

• Active input scale can be selectable

• Limit and direction of the output scale can be freely assigned

• Two universal inputs for Siemens 1000 ohm nickel (Ni 1000), 1000 ohm platinum

(Pt 1000) temperature sensors and 0 Vdc to 10 Vdc signals

• Unit can be set as °F, °C, % or no specified unit

• Two modulating 0 to 10 Vdc signal outputs, direct or reverse action

• One digital input for day/night changeover

• Entering or changing of all data via operating buttons on the controller, possible

without additional tools

• Computer connection for downloading canned applications via the software tool

Product Number RWD62U

Siemens Building Technologies, Inc.

Technical Instructions RWD62U Universal Controller

Document Number 155-737

January 14, 2005

Warning/Caution Notations

CAUTION:

Equipment damage may occur if you do not follow a

procedure as specified.

Specifications

Power Supply

Operating voltage 24 Vac + 20%

Frequency 50/60 Hz

Power consumption 2.5 VA

LCD Actual and nominal values Four digits

Setpoint adjustment range -58°F to 302°F (-50°C to 150°C)

Display Resolution

(does not relate to controller

accuracy)

Siemens Ni 1000 ohm 1°F (0.5°C)

Pt 1000 ohm 1°F (0.5°C)

Active sensor Depends on setting range

Environmental Conditions Storage and transport

Temperature -13°F to 158°F (-25°C to 70°C)

Humidity <95% rh

Operation

Temperature 32°F to 122°F (0°C to 50°C)

Humidity <95% rh

Regulatory Approvals Conforms to requirements

UL UL listed to 916 Energy Management

Equipment

Terminals Screw terminals, min./max. conductors Minimum: 24 AWG (1)

Maximum: 16 AWG (2), or

14 AWG (1)

Weight RWD62U Controller 10.4 oz (295 grams)

With packaging 12.24 oz (347 grams)

Analog Inputs X1, X2

Siemens Ni 1000 ohm @ 32°F

(0°C)

Controller measuring range -58°F to 302°F (50°C to 150°C)

Maximum cable length for 14 AWG Maximum 984 ft (300 m)

Pt 1000 ohm at 32°F (0°C) Controller measuring range -4°F to 356°F (-20°C to 180°C)

Maximum cable length for 14 AWG Maximum 984 ft (300 m)

Analog voltages

(For measured variable in °F,

°C, % or without unit)

Range 0 to 10 Vdc corresponding to

adjustable range from –100 to

8000 (°C, °F, % or no unit)

Maximum cable length for 14 AWG Maximum 984 ft (300 m)

Remote setpoint X2 Range 0 to 1000 ohm corresponding to

adjustable range from –100 to

8000 (°C, °F, % or no unit)

Maximum cable length for 14 AWG Maximum 984 ft (300 m)

Digital input D1 Polling voltage for control commands (D…M) 15 Vdc

Current consumption <15 mA

Analog outputs Y1, Y2 Range 0 to 10 Vdc

Maximum current +1 mA

Accessories ARG62.21 Protective enclosure for wall mounting.

SEH62.1U Program Clock

SEM62.2U 24/120 Vac Transformer

125-3481 RWD Controller Programming Tool (CD)

RWDTKU Tool Kit

Page 2 Siemens Building Technologies, Inc.

RWD62U Universal Controller Technical Instructions

Document Number 155-737

January 14, 2005

Function Summary • Controller

Stand-alone controller with two 0 to 10 Vdc outputs with independent adjustment

on each sequence for direct acting and/or reverse acting. Adjustable parameters,

including proportional band and integral action time.

• Auxiliary selectable function

• Universal input X2 for one of the following auxiliary functions:

− P+I limiter function (Absolute and Relative)

− Remote setpoint

− Cascade control

− Setpoint compensation

− Winter/summer operation

− Maximum priority

• Digital input D1 for setpoint changeover day/night

Equipment

Combinations

The following Siemens devices can be connected to RWD62U Universal Controllers.

Other combinations with units from third-party manufacturers are possible, if the

input and output specifications match the RWD62U.

Table 1.

Description Document Number

Sensor with Siemens Ni 1000 temperature sensing element

QAA25U Room temperature sensor with setpoint adjuster

155-330

GIB Series 310 lb-in Non Spring Return Actuators

GBB Series 177 lb-in Non Spring Return Actuators

155-176P25

155-177P25

GEB Series 132 in-lb Non Spring Return Actuators 155-318P25

GCA Series 142 in-lb Spring Return Actuators 155-173P25

155-174P25

155-175P25

GMA Series 62 in-lb Spring Return Actuators 155-315P25

SKD Valve Actuator with proportional input 155-180P25

SKB/SKC Valve Actuator with proportional input 155-163P25

SQX Valve Actuator with proportional input 155-182P25

SQS Valve Actuator with proportional input 155-190P25

SSC Valve Actuator with proportional input 155-313P25

SSB Valve Actuator with proportional input 155-192P25

Electric Rack and Pinion proportional actuator 155-541P25

1/2 to 2-inch two-way globe valves 155-184P25

1/2 to 2-inch three-way globe valves 155-185P25

2-1/2 to 6-inch two-way flange valves 155-159P25

2-1/2 to 6-inch three-way flange valves 155-160P25

MT Series 1/2 to 1-1/2-inch two-way globe valves 155-196P25

MT Series 1/2 to 1-1/2-inch three-way globe valves 155-197P25

MZ Series 1/2 to 1-inch two-way globe valves 155-198P25

MZ Series 1/2 to I-inch three-way ball valves 155-199P25

Differential Pressure Sensor 155-719

Siemens Building Technologies, Inc. Page 3

Technical Instructions RWD62U Universal Controller

Document Number 155-737

January 14, 2005

Software Tool An optional, user-friendly, Windows® 95 (or later) based software tool for controller

application selection and parameter adjustment is available. It provides you with a

printout of the controller settings. This tool allows controller programming prior to

installation.

Functions

Controller Type

The RWD62U is a stand-alone universal controller, which performs both primary and

auxiliary control functions. The respective mode is defined by entering the

corresponding configuration and setting parameters via the push buttons on the

controller or the software tool.

Main Functions The RWD62U controller can be programmed as follows:

• One sequence: Y1 or Y2 Reverse or direct acting

• Two sequences: Y1 and Y2 Reverse and direct acting or

Y1 and Y2 Reverse and reverse acting or

Y1 and Y2 Direct and direct acting

NOTE: Direct Acting – As air temperature increases, the control output increases.

Reverse Acting – As air temperature increases, the control output

decreases.

TH0599R3

= TEMPERATURE SENSOR

= AIR DAMPER ACTUATOR

= HEATING COIL

= COOLING COIL

= HEATING OR COOLING COIL (TWO-PIPE)

= FAN OR PUMP

= TIME CLOCK

= REMOTE SET POINT UNIT

= OUTSIDE AIR SENSOR

Figure 1. Frequently Used Symbols in Application Drawings.

TH0786R1

Output

Voltage

Setpoint

Temp.

Figure 2. One Sequence Heat, Direct

Acting or Reverse Acting

(Application 10 to 19).

Output

Voltage

Temp.

Setpoint

TH0787R1

Figure 3. Two Sequence Heat, Two Direct

Acting or Two Reverse Acting Sequences

(Application 20 to 29).

Setpoint Temp

Output

Voltage

TH0788R1

Setpoint

Figure 4. One Direct Acting Heat and One

Direct Acting Cool or One Reverse Acting

Heat and One Direct Acting Cool

Sequence

(Application 30 to 39).

TH0789R1

Temp.

Output

Voltage

Setpoint

Figure 5. One Direct Acting Cool or One

Reverse Acting Cool Sequence

(Application 40 to 49).

Page 4 Siemens Building Technologies, Inc.

RWD62U Universal Controller Technical Instructions

Document Number 155-737

January 14, 2005

Output

Voltage

Setpoint Temp.

TH0790R1

Figure 6. Two Direct Acting Cool or Two Reverse Acting Cool Sequences

(Application 50 to 59).

Universal Input X1 The primary input for a Siemens Ni 1000 temperature sensor, a Pt 1000 temperature

sensor, or a 0 to 10 Vdc active input.

Universal Input X2 The secondary input for a Siemens Ni 1000 temperature sensor, a Pt 1000

temperature sensor, an active/passive remote setpoint transmitter, or a 0 to 10 Vdc

active input.

Digital Input D1 Selects the day/night changeover. Changeover occurs via potential-free dry contacts

between D1 and M. Typically, a time clock controls D1 input.

Analog Outputs Each output (Y1, Y2) can be configured for either reverse or direct acting. The

modulating voltage output (Y…) controls the devices requiring a 0 to 10 Vdc signal.

Example

Y2Y1

Temp.

TH0791R1

Figure 7. Constant Volume with Temperature

Control, Direct Acting/Reverse Acting.

X1 Room temperature

Y1 Heating, direct action

Y2 Cooling, reverse action

Y2Y1

Temp.

TH0811R1

Figure 8. Constant Volume with Temperature

Control, Reverse Acting/Direct Acting.

X1 Room temperature

Y1 Heating, reverse action

Y2 Cooling, direct action

Auxiliary Functions One of the following auxiliary functions can be selected:

• P+I limiter (Absolute, #x2 and Relative, #x3)

• Remote setpoint, #x1

• Cascade control, #x5

• Setpoint compensation, #x4

• Winter/summer operation, Digital #x6, Analog #x7

• Maximum priority, #x8

• Main loop 0 to 10V input, #x9

Day and night operation mode is also available.

Siemens Building Technologies, Inc. Page 5

Technical Instructions RWD62U Universal Controller

Document Number 155-737

January 14, 2005

P+I Limiter Function

NOTE: In the following

illustrations, the

heating and cooling

outputs are D.A.

Outputs can be

reversed.

TH0794R1

Y2Y1

Temp.

Figure 9. P+I Limiter Function.

The limiter function with P+I control

enables absolute (or relative) maximum

or minimum limitation of the supply air

temperature (X2).

When the value drops below or exceeds

the limiter setpoint, the limiter function

controls and takes priority over the main

setpoint.

Remote Setpoint

NOTE: You cannot select

the remote setpoint

auxiliary function in

Night mode.

Y2Y1

Temp.

TH0793R1

Figure 10. Remote Setpoint.

A remote setpoint transmitter (QAA25U),

connected to X2 and configured

accordingly, enables setpoint

adjustment.

Active measurement from 0 to 10 Vdc

corresponding adjustable range from

–100 to 8000 units

Passive measurement from 0 to 1000 Ω

corresponding adjustable range from

–100 to 8000 units

Cascade Control

TH0794R1

Y2Y1

Temp.

Figure 11. X2 Supply Air Temperature

Sensor.

You can select the P+I/P+I room/supply

air temperature cascade control. In this

case, the virtual P+I room temperature

controller determines the setpoint within

the limiter setpoints for the P+I supply air

temperature controller.

Maximum Priority

NOTE: You cannot select

the maximum priority

auxiliary function in

Night mode.

TH0795R1

Y2Y1

Temp.

Figure 12. Maximum Priority,

Cooling.

If the value (0 to 10V) of the input X2 is

greater than the calculated output of the

cooling sequence, the output will use the

X2 input value as output value. This is

active even when the controller is

working with the heating sequence.

Setpoint Compensation

TH0796R1

Temp.

Figure 13. Setpoint Compensation.

The temperature setpoint X1 is shifted

by the temperature as measured at

sensor X2.

Configuration of the RWD62U defines

the influence on setpoint X1.

The example shows the room air

temperature setpoint as shifted by the

outside temperature.

Page 6 Siemens Building Technologies, Inc.

RWD62U Universal Controller Technical Instructions

Document Number 155-737

January 14, 2005

Winter/Summer Operation

TH0797R1

Y2Y1

Temp.

Summer

Setpoint Winter

Setpoint

Figure 14. Winter/Summer Operation.

A digital switch or analog input between

terminals X2 and M will implement

winter/summer changeover.

When adjusting setpoints, the heating

setpoint must be less than the cooling

setpoint.

Digital changeover

When the contact is closed, summer

operation is selected. Reverse acting

output (Y1 only) is set to direct action

(cooling).

Analog changeover

Summer operation is selected when the

X2 input exceeds the setpoint Reverse

acting output (Y1 only) is set to direct

action (cooling).

Day/Night Setpoint

TH0798R1

Y2Y1

Temp.

Figure 15. Day/Night Setpoint.

A contact between terminals D1 and M

can be used to implement setpoint

changeover for day/night operation.

When the contact is open, the setpoints

for day operation are selected.

When the contact is closed, the setpoints

for night operation are selected.

During the night mode, the following

auxiliary functions are disabled: remote

setpoint, absolute/relative limiter,

setpoint compensation and maximum

priority.

Mechanical Design

Protective Housing

ARG62.21

• This UL-approved plastic housing protects the controller when mounted outside a

control panel, such as on ducts, walls and in mechanical rooms. This housing

also prevents inadvertent contact with voltage supplying parts such as the

connecting terminals.

• The RWD62U clips into the housing.

• The cable entries are located at the top and the bottom of the ARG62.21

housing.

• The front has an opening for the LCD display and the programming buttons.

Terminals Plug-in screw terminals

Siemens Building Technologies, Inc. Page 7

Technical Instructions RWD62U Universal Controller

Document Number 155-737

January 14, 2005

Operating and Display

Elements The RWD62U is operated by the buttons on the controller front. Additional tools are

not necessary. The controller can also be programmed via the software tool, which

plugs into the nine-pin port.

TH0799R1

LCD Display

Software Tool

Nine Pin Port

Program and Display

Function Buttons

Figure 16. RWD62U Universal Controller.

LCD The LCD shows the following information for normal operation:

• Current operating values (maximum four digits)

• Current setpoints (day/night)

• Application number

• Control sequencing diagram

• Auxiliary input value

• Selected auxiliary function

Operating Buttons The controller has three operating buttons for the following functions:

The SELECT ●button is used to enter or save the value adjustment.

The operating buttons are used for viewing and adjusting parameters.

Configuration To configure the controller, follow the instructions supplied with the controller.

Page 8 Siemens Building Technologies, Inc.

RWD62U Universal Controller Technical Instructions

Document Number 155-737

January 14, 2005

Installation Notes The RWD62U controller can be mounted as follows:

NOTE: Observe all local installation regulations and building codes.

A On a DIN rail at least 4.7 inches (120 mm) long

B Wall-mounted with two #6 screws

C Front-mounted using standard hardware:

• One DIN rail 5.9 inches (150 mm) long

• Two hexagonal blocks 1.97 inches (50 mm)

• Washers and screws

D In the ARG62.21 protective housing

TH0741R1

AB C D

Figure 17. Mounting Options.

Electrical Installation Notes

CAUTION:

• Standard cables can be used for the controller. However, when

mounting in an environment greatly exposed to Electrical Magnetic

Interface (EMI), use only shielded cables.

• The RWD62U is designed for 24 Vac operating voltage.

• Use safety insulating transformers with double insulation; they

must be designed for 100% duty.

• When using several transformers in one system, the connection

terminals G0 (ground) must be galvanically connected.

• Supplying voltages above 24 Vac to low voltage connections may

damage or destroy the controller or any other connected devices.

• Connections to voltages exceeding 24 Vac endanger personal

safety.

• The ARG62.21 Protective Housing does not provide grounding

between conduit connections. Use grounding bushings and jumper

wires or equivalent.

Commissioning Notes A commissioning booklet is included with the RWD62U controller.

Observe the following:

• The controller must be configured for application-specific operation using the

standard application number.

• Application-specific fine tuning can be performed if required (see the

commissioning booklet).

• Power supply to the controller and the connected devices must be guaranteed.

• Values and settings entered remain available even on power failure.

Siemens Building Technologies, Inc. Page 9

Technical Instructions RWD62U Universal Controller

Document Number 155-737

January 14, 2005

Wiring Diagrams

G0 Y2

D1 M X1 M X2 M

Y1 M

Tool

TH0800R1

D1 Digital input

G, G0 24 Vac supply

M Ground (G0) for signal inputs

and universal inputs and analog

outputs

X1 Signal input (main input:

Siemens Ni 1000, Pt 1000 and 0

to10 Vdc)

X2 Signal input (aux. Input:

Siemens Ni1000, Pt 1000, 0

to10 Vdc and 0 to 1000 Ωor

0 to 10 Vdc remote setpoint)

Y1, Y2 Analog outputs

Tool Communication port for PC

(9-pin plug)

Figure 18. RWD62U Wiring Diagram.

TH0801R1

Y..

BM BM

X1 X2MM

Y..

X2X1

24 V SN

24 V SP

TOOL

N1 RWD62U controller

PC Personal computer

S1 Time clock or switch

SN System neutral

SP System potential

X1 Main input (Termination G appears when X1 is an active sensor)

X2 Auxiliary input or remote setpoint (Termination G appears when X2 is an

active sensor)

Y1, Y2 Valve actuator 1 and 2/Damper actuator 1 and 2

Figure 19. Connection Diagram.

CAUTION:

if you use a DESKTOP computer, the TOOL signal ground is

galvanically connected to G0 inside the controller. If the signal line of

the computer is grounded to Earth, the G0 line after TOOL connection

will be grounded as well.

Page 10 Siemens Building Technologies, Inc.

Other manuals for RWD62U

Table of contents

Other Siemens Controllers manuals

Siemens

Siemens SIMATIC S5-100U User manual

Siemens

Siemens LME7 Series Operator's manual

Siemens

Siemens SIRIUS M200D User manual

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens BT300 LonWorks User guide

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens OpenAir GEB 131.1E User manual

Siemens

Siemens GEB 4 Series User manual

Siemens

Siemens MCC-3298 User manual

Siemens

Siemens PXC Compact Series User manual

Siemens

Siemens Stratos Outstation Guide

Siemens

Siemens N 543D31 User manual

Siemens

Siemens RVL471 Operator's manual

Siemens

Siemens Simatic S7-400 User manual

Siemens

Siemens SITOP UPS1600 under STEP 7 V12 User manual

Siemens

Siemens POLYCOOL RWR470.10 Operator's manual

Siemens

Siemens Simatic S7 Series User guide

Siemens

Siemens SINUMERIK 840D sl User manual

Siemens

Siemens 7SR224 Use and care manual

Siemens

Siemens SQL36E50F04 User manual

Siemens

Siemens RVL481 Operator's manual

Siemens

Siemens SSA Series User manual

Siemens

Siemens RMZ791 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide