Siemens SITOP UPS1600 under STEP 7 V12 User manual

SITOP UPS1600 under STEP 7 V12

___________________

SITOP UPS1600 under STEP 7

V12

Getting Started

Introduction

Safety notes

Description

Assigning the IP address

Installing and configuring the

SITOP UPS1600 in STEP 7

V12

Parameterizing the SITOP

UPS1600

Siemens AG

Industry

Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

Ⓟ

02/2014 Technical data subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SITOP UPS1600 under STEP 7 V12

Getting Started, 3

Table of contents

1 Introduction...................................................................................................................................5

1.1 Purpose of this document......................................................................................................... 5

1.2 Technical support..................................................................................................................... 5

1.3 Additional documentation ......................................................................................................... 6

2 Safety notes .................................................................................................................................7

3 Description ...................................................................................................................................9

3.1 System overview...................................................................................................................... 9

4 Assigning the IP address.............................................................................................................. 11

5 Installing and configuring the SITOP UPS1600 in STEP 7 V12 ......................................................... 17

6 Parameterizing the SITOP UPS1600 ............................................................................................. 25

6.1 Buffering an S7 IO controller, including the I/O when the power fails....................................... 25

6.2 Switching off the UPS when the power fails by a user program............................................... 29

SITOP UPS1600 under STEP 7 V12

Getting Started, 5

Introduction

1.1

Purpose of this document

This Getting Started guides you through configuring the UPS1600 under STEP 7 V12 for the

following two tasks:

●Buffering the S7 IO controller, including the I/O when the power fails

●Switching off the UPS when the power fails by the user program

Basic knowledge required

The following are required to understand the Getting Started:

●Knowledgeable about using personal computers with the Windows operating system

●Knowledgeable about how to configure an uninterruptible power supply using the

UPS1600, including the S7 IO controller and connected battery modules

●Creating and editing projects under STEP 7 V12 in the TIA-Portal.

Range of validity

Getting Started is valid for STEP 7 V12, Version 12.0 with service pack 1 (SP1).

1.2

Technical support

Technical support for all IA/DT products can be accessed through the following

communication channels:

●Phone: + 49 (0) 911 895 7222

●E-Mail (mailto:support.automation@siemens.com)

●Internet:

Online support request form (http://www.siemens.com/automation/support-request)

Technical documentation on the Internet

Operating instructions and manuals for SITOP are available in the Internet:

Operating instructions/manuals (http://www.siemens.com/sitop/manuals)

SITOP power supply homepage

General news about our power supplies is available in the Internet at the SITOP home page

(http://www.siemens.com/sitop).

Introduction

1.3 Additional documentation

SITOP UPS1600 under STEP 7 V12

6Getting Started,

1.3

Additional documentation

Further information is available in the following documents:

●UPS1600 and UPS1100 manuals

●IO controller manual

●STEP 7 V12 manual

SITOP UPS1600 under STEP 7 V12

Getting Started, 7

Safety notes

WARNING

Correct handling of the devices

When operating electrical devices, it is inevitable that certain components will carry

dangerous voltages.

Therefore, failure to handle the units properly can result in death or serious physical injury

as well as extensive property damage.

Only appropriately qualified personnel may work on or in the vicinity of this equipment.

Perfect, safe, and reliable operation of this equipment is dependent on proper

transportation, storage, installation and mounting.

Before installation or maintenance work can begin, the system's main switch must be

switched off and measures taken to prevent it being switched on again.

If this instruction is not observed, touching live parts can result in death or serious injury.

The relevant DIN/VDE regulations or country-specific specifications (e.g. VDE 0510 Part 2 /

EN50272-2) must be observed for the storage, assembly and operation of the lead

accumulators. It must be ensured that the battery location is suitably ventilated. Potential

ignition sources must be separated by at least 50 cm.

SITOP UPS1600 under STEP 7 V12

Getting Started, 9

Description

3.1

System overview

Application

The principal tasks that you can perform with the SITOP UPS Management:

●Connecting the uninterruptible SITOP UPS1600 power supply to the IO controller S7

●Configuring the SITOP UPS1600 uninterruptible power supply

●Protecting a computer or a computer network using the uninterruptible power supply

●Defining the battery maintenance intervals

Device integration

SITOP UPS Management supports the following devices:

●UPS1600

●UPS1100

UPS1600 can be used with STEP 7 V12 as of version 12.0 with Servicepack 1 (SP1).

After the UPS1600 has been saved in the hardware catalog of STEP 7 V12 by installing the

hardware support package, it can be integrated into projects, parameterized and diagnosed.

Languages

German, English

French, Italian, Spanish and Chinese being prepared.

Table of contents

Other Siemens Controllers manuals

Siemens

Siemens 3RK1308-0 00-0CP0 Series Technical Document

Siemens

Siemens TUTORbit POL687 Service manual

Siemens

Siemens SITRANS LUT400 User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SSA955 User manual

Siemens

Siemens SSA911.01TH User manual

Siemens

Siemens SIRIUS 3SX3217 User manual

Siemens

Siemens 5WG1 536-1DB51 User manual

Siemens

Siemens SITRANS L 7ML5400 User manual

Siemens

Siemens OpenAir User manual

Siemens

Siemens SIMATIC S7-1200 User manual

Siemens

Siemens RAJA+ 3TE7131-1HC14-1A Operating instructions

Siemens

Siemens OpenAir GIB132.1P Owner's manual

Siemens

Siemens Flowrite 599 Series User manual

Siemens

Siemens acvatix SKD32 Series User manual

Siemens

Siemens SIRIUS User manual

Siemens

Siemens Albatros2 RVA78.690 User manual

Siemens

Siemens OpenAir GND12x.1 Series Service manual

Siemens

Siemens 540-716 Service manual

Siemens

Siemens SIMATIC S5 User manual

Siemens

Siemens Simatic S7-400 Quick guide

Siemens

Siemens 5WG1 513-1AB11 User manual

Siemens

Siemens SINAMICS S120 User manual

Siemens

Siemens SINUMERIK 808D User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual

3M MicroTouch EX113 reference guide