Siemens MPS-6 User manual

Installation Instructions

Model MPS-6

Power Supply Module

P/N 315-090334-8

OPERATION

The Model MPS-6 from Siemens Industry, Inc. is a

fully supervised power supply that provides the MXL

System with primary 24 VDC power. It is rated at 6.5

amps and is unfiltered and unregulated. The MPS-6

supplies the MXL Control Panel or PSR-1 and its

expansion modules with the power required for

normal operation. The module incorporates a 2 amp

resettable circuitbreaker on the primary input and

includes a built-in AC line filter for surge and noise

suppression. The MPS-6 mounts in an MXL enclo-

sure backbox.

INSTALLATION

Always remove power before installation.

The installation kit for the MPS-6 includes the

following:

Four #10 nuts

Two #10 lockwashers

Two #10 flat washers

Two ¼" nuts

One 14 gauge green ground strap

The MPS-6 is designed to operate from a 120 VAC,

60 Hz power source. Use a separate or dedicated

circuitbreaker. Wire in accordance with local codes

and Article 760 of the NEC, NFPA 70, latest edition.

Run the earth ground from a suitable source to the

MPS-6. Check local requirements. Conduit is not

an acceptable conductor.

1. Make sure that the dedicated circuitbreaker

for the MPS-6 is turned off at the mains.

2. Place the mounting bracket for the MPS-6 over

the two studs provided in the enclosure. (Refer to

Figure 1.)

3. Secure the MPS-6 to the enclosure by slipping the

flat washers, then the lockwashers, and finally the

nuts over the two studs. Tighten them securely.

4. Connect the AC mains to the MPS-6:

Terminal

Black (hot) 1

White (neutral) 2

Green (earth ground) 3

5. Install the 14 gauge green ground strap spade lug

side to Terminal 3 (green, earth ground) of the

MPS-6. Secure the ring lug side of the ground

strap to the nearest available stud in the enclo-

sure. The stud size may vary depending on the

actual system modules and enclosure used.

Because the stud may be either a #10 thread or

¼" thread, nuts for both have been provided. The

ground strap provided is long enough for all

applications and the ring lug is good for both #10

and ¼" studs. If possible, install the ring lug under

one of the lock-washers and nuts which secure

the MPS-6 itself.

6. When used with a PSR-1:

Connect the 3-wire cable coming from the MPS-6

to the PSR at P12.

When used with an MMB-1/-2/-3 or SMB-1/2:

Connect the 3-wire cable coming from the MPS-6

to the MMB-1/-2/-3 or the SMB-1/2 at P1.

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

P/N 315-090334-8

Figure 2

Front of MPS-6

Figure 1

MPS-6 in MXL Enclosure

POWER CABLE TO:

MMB-1/-2/-3, P1

SMB-1/-2, P1

PSR-1, P12

Other Siemens Control Unit manuals

Siemens

Siemens SIMATIC 6ES7135-4MB02-0AB0 User manual

Siemens

Siemens 550-818B User manual

Siemens

Siemens SINAMICS S Series User manual

Siemens

Siemens SIRIUS PROFINET User manual

Siemens

Siemens LMS14 User manual

Siemens

Siemens SITOP modular 6EP1961-3BA20 User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 User manual

Siemens

Siemens PM-E F pm DC24V PROFIsafe User manual

Siemens

Siemens SIRIUS 3RW5 series User manual

Siemens

Siemens SIRIUS 3RW5 series Technical Document

Siemens

Siemens CM 1243-5 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens SIDOOR AT40 User guide

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens LYC11 User manual

Siemens

Siemens Simatic S7-300 User manual

Siemens

Siemens LOGO! CIM User manual

Siemens

Siemens MICROMASTER Vector 6SE32 User manual

Siemens

Siemens SIMATIC ET 200AL User manual

Siemens

Siemens XC1003-A Instruction Manual

Siemens

Siemens SINAMICS SM120 User manual

Siemens

Siemens SITOP DC UPS 6EP1931-2DC21 User manual

Siemens

Siemens 3VL93 Series User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual