Siemens HCP User manual

SiemensSiemens

Siemens IndustryIndustry

IndustryIndustry

Industry,,

,Inc.Inc.

Inc.Inc.

Inc.

BuildingBuilding

Building

Tecec

ecec

echnologies Dihnologies Di

hnologies Dihnologies Di

hnologies Divisionvision

visionvision

vision

P/N 315-034860-13

Intelligent Control Point

Installation Instructions

Model HCP

INTRODUCTION The Model HCP Intelligent Control Point from Siemens

Industry, Inc. provides remote, independent control of

any of the following:

1. A notification appliance circuit (NAC)

2. A telephone zone (XLS only)

3. A speaker zone (25V or 70.7V RMS) (XLS only,

FV2025/2050, FV922/924)

The HCP communicates through the DLC device loop

card of the FireFinder-XLS System, the FS-DLC device

loop card of the FS-250 System, the FC922/FV922,

FC2025/FV2025 periphery FCI2016 Board (250p)

detector circuits, and the FC2050/FV2050, FC924/FV924

FCI2017 periphery board (500p) detector circuits. Each HCP

uses one device address on the device loop.

PROGRAMMING Use the DPU Programmer/Tester to program and test the module.

The HCP may only be assigned addresses 1 to 60. It is recommended to program

the HCP devices first to ensure that enough addresses have been reserved for them.

Other devices may then be assigned to addresses in this range that were not

assigned to an HCP.

Disconnect wire at terminal 1 and 2 on TB1 before programming.

To set the HCP device address:

• Plug the programming cable of the DPU Programmer/Tester into the two-

pin programming points on the HCP. (See Figure 1 for location.)

• Set the device address for the HCP by following the instructions in the DPU

Programmer/Tester Manual, P/N 315-033260.

Each HCP can be assigned a custom message using either the Zeus Programming Tool

(XLS System), the FS-CT2 (FS-250 System), the FC2025/2050, FV2025/2050 FSX2002

Engineering Tool, or the FC922/924, FV922/924 FSX7212 Engineering Tool. Refer to

the Zeus Quick Start Manual, P/N 315-033875, or the FS-250 Programming Manual, P/

N 315-049403, as applicable.

PROGRAMMING

POINTS

DEVICE ADDRESS:

DISCONNECT WIRE AT TERMINAL "1" &"2"

SIEMENS INDUSTRY, INC.

CAUTION

ONTB1BEFOREPROGRAMMING

FLORHAM PARK, NJ, 07932

INSTALLATION INSTRUCTIONS

TB2ONBACKSIDE

P/N 315-034860

SIEMENS

MODEL: HCP

TB1ONBACKSIDE

654321

123456

Figure 1

HCP Intelligent Control Point

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-132

COMPATIBILITY The following minimum revisions are required for proper operation of the HCP:

:METSYSSLX:METSYS052-SFMETSYS02SF

CLD0000.00.40CLD-SF05.1

OGISED

IMP0000.00.40CAN81.20502/5202CFxx.xx.14

21-CSP0000.00.70 LENAP0.50502/5202VFxx.xx.06

04-CAZ 0000.80.20 *0000.80.031

SUEZ9100.00.40

ORPSUREBREC

429/229CFxx.xx.14

429/229VFxx.xx.06

htiwelbitapmocTONera0000.42.20.veRdna0000.12.20.veR,0000.90.031/0000.

90.20.veR04-CAZ* .0000.01.031/0000.01.20.veRro0000.80.031/0000.80.20.veRottreveR.PCHeht

WIRING

Remove all system power before installation, first battery then AC. (To power up,

connect the AC first, then the battery.)

Power down the 24 VDC power supply and the input source (ZAC, etc.) before

installing the HCP.

All wiring must comply with national and local codes. All wire must be 18 AWG

minimum, 12 AWG maximum.

Device Loops The HCP communicates with the FireFinder-XLS/FS-250/Desigo FC2025/2050,

FV2025/2050/Cerberus PRO FC922/924, FV922/924 Systems through its addressable

device loops.These loops are connected to the DLC via terminal blocks on the CC-5

or CC-2 cardcage (XLS) or to the FS-DLC via TB3 on the FS-MB/FS-MB2 main board

(FS-250).They may be wired Class A (Style 6) or Class B (Style 4). Figure 2 shows

both wiring types and the connections to the DLC. See the DLC Installation Instruc-

tions, P/N 315-033090, for more information. Figure 3 shows both wiring types and

connections to the FS-DLC. See the FS-250 Installation, Operation and Maintenance

Manual, P/N 315-049353, for more information. Figure 4 shows both wiring types and

connections to the Periphery boards. See the Desigo FC2025/2050 FV2025/2050

Configuration Manual, Document ID A6V10315023, for more information. Figure 5

shows both wiring types and connections to the Periphery boards. See the Cerberus

PRO FC922/924 FV922/924 Configuration Manual, Document ID A6V10333423, for

more information.

HCP Power Supply For FireFinder-XLS Systems, compatible power supplies for the HCP are the PSC-12,

PSX-12, and PAD-4. Wiring should be connected to TB3 on the PSC-12 and PSX-12, or

the auxiliary power supply on the PAD-4.

For FS-250 Systems, the HCP is powered by the NAC circuits and PAD-4. Wiring

should be connected to the NAC circuits on the main board or the auxiliary power

supply on the PAD-4.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-133

HCP

TB1

HCP

TB1

HCP

TB1

12345678

910111213141516

CLASS A WIRING*

NO T-TAPPING ALLOWED

BOTH ZONES MUST BE WIRED AS CLASS A

12345678

910111213141516

CLASS B WIRING**

T-TAPPING ALLOWED

BOTH ZONES MUST BE WIRED AS CLASS B

*OPERATES IN FULL CONFORMANCE WITH STYLE 6 (ULC DCLA)

ZONE 1

DLC LOCATED IN

ONE SLOT OF CC-5 / CC-2

LINE 1

LINE 1 (RETURN)

LINE 1 (OUT)

ZONE 2

LINE 2

LINE 2 (OUT)

LINE 2 (RETURN)

NOT USED

**OPERATES IN FULL CONFORMANCE WITH STYLE 4 (ULC DCLB)

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

ZONE 1 ZONE 2

DLC LOCATED IN

ONE SLOT OF CC-5 / CC-2

HCP

TB1

HCP

TB1

4 3 2 1

A WIRIN

CLASS B WIRING

HCP

TB1

HCP

TB1

HCP

TB1

HCP

TB1

1+ 1- 2+ 2-

X1401/X1402

X1801/X1802 4 3 2 1

1+ 1- 2+ 2-

Detector circuits on periphery board

for FC922/FV922

FC2025/FV2025

X1401/X1402

X1801/X1802

Figure 2

FireFinder-XLS Device Loop

Connections

NOTES

1. Loop resistance 50 ohms

Max with 252 devices on

the loop. Refer to the DLC

Installation Instructions,

P/N 315-033090 if the

number of devices is less

than 252.

2. 12-18 AWG wire.

3. No EOL device required.

4. Supervised, power limited

per NEC 760.

5. All wiring must conform

to national and local

electrical codes.

Figure 3

FS20 Device Loop

Connections

NOTES

1. Loop resistance 180 ohms

max with 252 devices on

loop.

2. 12-18 AWG wire.

3. No EOL device required.

4. Supervised, power limited

per NEC 760.

5. All wiring must conform

to national and local

electrical codes.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-134

CLASS A* INSTALLATION

NO T-TAPPING ALLOWED

CLASS B** INSTALLATION

T-TAPPING ALLOWED

*OPERATES IN FULL CONFORMANCE WITH STYLE 6

(ULC DCLA)

**OPERATES IN FULL CONFORMANCE WITH STYLE 4

(ULC DCLB)

ZONE

NOT USED

Loop Circuit

FS-DLC Device

NOT USED

Loop Circuit

FS-DLC Device

HCP

TB1

HCP

TB1

HCP

TB1

LINE 1 (RETURN)

LINE 1 (OUT)

LINE 2 (OUT)

LINE 2 (RETURN)

ZONE

LINE 1

LINE 2

HCP

TB1

HCP

TB1

HCP

DPU Loop Test When performing a loop test with the DPU be sure to apply power to the HCP.

Without power applied to the HCP a blinking “C” will appear on the DPU, indicating

that the HCP is in trouble.

HCP As NAC Module This application uses the principle of polarity reversal to activate notification appli-

ances. Wiring is shown in Figure 4. Connect the HCP output zone wiring to the (+)

and (-) terminals of each notification appliance as shown in Figure 4. For a list of

compatible devices, refer to P/N 315-096363.

When used as a NAC module, the 24VDC provides power for the supervision circuitry

and to the notification appliances when they are activated.The power source must be

power limited. See the HCP Power Supply section (above) for compatible power sources.

The maximum output load that may be connected to an HCP is 1.5A at 24 VDC. If the 24

VDC is lost or the NAC line is broken or shorted while the HCP is in supervisory mode, a

trouble condition displays at the FireFinder-XLS, FS-250 System control panel, the Desigo

FC2025/2050, FV2025/2050 Operating Unit, and the Cerberus PRO FC922/924, FV922/

924 Operating Unit. For FS-250 Systems, the NAC circuit must be set to “always on” in

the panel or FS-CT2 configuration tool. See the Line Resistance table below for the

allowable line resistance for each HCP output circuit.

ECNATSISERENILTIUCRICTUPTUOPCHELBAWOLLAMUMIXAM ECNATSISERENILDNATNERRUCRESIRCDDEIFICEPSROF

MUMIXAM RESIR

CD TNERRUC )spmAni(

)smhOni(ECNATSISERRESIRCD

mhO1.0mhO52.0mhO5.0mhO57.0mhO1smhO5.1

437.233.276.100.133.—

308.205.200.205.

100.1—

268.276.233.200.276.100.1

139.238.276.205.233.200.2

5.69.229.238.257.276.205.2

RESIRNOPCHHCAEROFECNATSISERPOOLMUMIXAM

SETON .seriwhtobroferadeificepssecnatsiseR.1 eratahtseilppusCDV42yrailixualacol,A4sdeecxetnemeriuqertne

rruclatotehtfI.2 .desuebyam,4-DAPsnemeiSsahcus,esugnilangisnoitcetorperifrofdetsilLU

NOTES

1. Loop resistance 50 ohms

Max with 252 devices on

the loop. Refer to the FS-

250 Manual, P/N 315-

049353 if the number of

devices is less than 252.

2. 12-18 AWG wire.

3. No EOL device required.

4. Supervised, power limited

per NEC 760.

5. All wiring must conform

to national and local

electrical codes.

Figure 4

FS-250 Device

Loop Connections

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-135

*REFER TO PAD-4 INSTALLATION INSTRUCTIONS

P/N 315-050217

FOR PROPER SETTING OF SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”

LL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.

POSITIVE AND NEGATIVE

GROUND FAULT

DETECTED AT

<500 OHMS FOR

TERMINALS 3-6 ON TB1.

HCP MODULE IS USED FOR

NAC SUPERVISION AND ACTIVATION

FROM

DLC/FS-DLC

DEVICE LOOP

LINE 1

LINE 2

EARTH

HCP HCP

HCP MODULE IS USED FOR

NAC SUPERVISION AND ACTIVATION

SHIELD EARTH

24 VDC

NAC UNITS

SEE P/N 315-096363

24K, W½,5%

EOL RESISTOR

P/N 140-034677 SHIELD

STYLE Y

SUPERVISED STROBEACTIVATION “SPECIALAPPLICATION”

SUPV: 1mA

ACTIVATED: 1.5A MAX

18.8V-28.2V FILTERED FULL WAVE RECTIFIED

POLARITY SHOWN IN ACTIVE STATE

STYLE Z

24K, W, 5%½

EOL RESISTOR

P/N 140-034677

DC INPUT RATED

18.8-28.2VDC

SUPV: 30mA

ACTIVATED: 1.5A MAX

6 5 4 3 2 1

1 2 3 4 5 6

PROGRAMMING

POINTS PROGRAMMING

POINTS

C INPUT: 18.8-28.2VDC FILTERED FULL WAVE

MODULE INPUT SUPPLY:

XLS: PSC-12 (TB3) or PSX-12 (TB3).

FS-250: FS-250 NAC Circuit.

XLS/FS-250: PAD-4* (TB16), FC2025/2050,

FV2025/2050, FC922/924, FV922/924,

FCI2016/2017-U1 PERIPHERY BOARD AUX

POWER OR UL LISTED REGULATED 24 VDC

POWER SUPPLY (POWER LIMITED).

HCP As Telephone Zone When the HCP is used as a telephone zone module (FireFinder-XLS System only) as

shown in Figure 5, the 24 VDC provides power to the supervision and call-in detection

circuitry. If the 24 VDC is lost, a trouble condition displays on the PMI/PMI-2 of the

FireFinder-XLS.

The HCP provides a dial tone when a Fireman’s Master telephone (FMT) is taken off

hook or when a Portable FireFighter’s telephone (PFT) is jacked in.

Each HCP can support a maximum of 5 phones off hook.Throughout the system, no

more than 10 phones may be off hook at any one time.

The supervised telephone common talk riser starts at the TZC-8B module in the CAB

backbox.The common talk riser connects continuously to each HCP with a 10K end

of line device at the last HCP. Tie the shield of these riser wires together using

terminal 5 of TB2 and isolate them from the system circuits and the earth ground.

Individual phones may not be connected to a riser that is wired to HCPs.TheTZC-8B

zone must be configured for Riser usage in Zeus.

Connect the supervised telephone zone wiring to the HCP with twisted pair cable.

Terminate at the last station with a 75K ohm end of line resistor. As with the com-

mon talk line described in the paragraph above, be sure that the shield is continuous

and isolated from both system circuits and earth ground and that the shields are

connected together using terminal 5 of TB-2.

Figure 5

HCP Used As An NAC Module

The input power and NAC power inputs onTB2 (1-4)

must be connected to the same source.

All HCPs connected to a given DLC/FS-DLC circuit

must reside within a single notification zone.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-136

POSITIVE AND NEGATIVE GROUND FAULT

DETECTED AT <500 OHMS FOR

TERMINALS 3-6 ON TB1.

75K, ¼W, +/-5%

EOL RESISTOR

P/N 140-050797

AT LAST FJ-303

FROM PREVIOUS HCP OR TZC-8B

(100 OHMS MAXIMUM

LINE RESISTANCE)

COMMON TALK RISER

(POWER LIMITED)

SEE TZC-8B INSTALLATION

INSTRUCTIONS, P/N 315-034110,

FOR RISER RATINGS

ELECTRICAL:

INPUT DC SUPPLY: 18.8 - 28.2VDC,

30mA MAX

FILTERED FULL WAVE

NOTES:

1. THE SHIELD ON THE COMMON TALK

LINE MUST BE CONTINUOUS AND

CONNECTED ONLY TO EARTH

GROUND AT CONTROL PANEL.

2. ALL WIRING MUST COMPLY WITH

NATIONAL AND LOCAL CODES.

3. 12-18 AWG OR AS REQUIRED

BY THE LOCAL AUTHORITY

HAVING JURISDICTION.

HCP DC SUPPLY

FROM PSC-12 (TB-3),

PSX-12 (TB-3),

OR PAD-4* (TB16)

75K, ¼W, +/-5%

EOL RESISTOR

P/N 140-050797

AT LAST STATION

10K, 1/2W, +/-5%

EOL RESISTOR

WARDEN’S STATIONS

(FTS SERIES)

SUPERVISED, 24 OHMS MAX

UNSHIELDED, USE TWISTED PAIR SUPERVISED

24 OHMS MAX

UNSHIELDED

USE TWISTED PAIR

FROM DLC DEVICE

LOOP IN CC-5 / CC-2

POWER LIMITED

SHIELD

REMOVE 10K TERMINATING RESISTORS FROM THE FJ-303sALL

SHIELD

WHITE

BLACK

WHITE

SHIELD

EARTH

SHIELD

BLACK

WHITE

BLACK

WHITE

BLACK

HCP HCP

EARTH

FJ-303

1 2 3 4 5 6

6 5 4 3 2 1 6 5 4 3 2 1

1 2 3 4 5 6

FJ-303

LINE 1

LINE 2

PROGRAMMING

POINTS PROGRAMMING

POINTS

*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”.

Figure 6

HCP Used As A Telephone Zone

HCP As (70.7V/25V) Speaker Zone in an XLSV System

When the HCP is used as a speaker zone (FireFinder-XLS System only), the 24 VDC

provides power to the supervision circuitry. If the 24 volts is lost or there is an open

or shorted speaker output line, a trouble condition displays on the PMI/PMI-2 of the

FireFinder-XLS.

The 70.7V/25V RMS audio input to the HCP must be power limited, such as from the

ZAC-40.The ZAC-40 supervises the audio connection path to the HCP and provides

up to 40 watts of power.The ZAC-40 can be wired StyleY (Class B) only. Refer to the

ZAC-40 Installation Instructions, P/N 315-035400 for further information. In order to

function properly during degrade mode, the DLC to which the HCP is connected

must be located in the same enclosure as the DAC-NET and ZAC-40 that supply

audio to the HCP.

When the HCP is used as a speaker zone, the output speaker lines are only super-

vised when the zone is not active.The audio output must not be allowed to exceed

25 watts. The approximate decibel loss for the total speaker zone wire length for

various wire gauge sizes is shown in Figure 7 for the 70.7V option and in Figure 8 for

the 25V option. Connect the speaker output as Style Y (Class B) as shown in Figure 9.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-137

HCP As (70.7V/25V) Speaker Zone in a FV2025/FV2050 or FV922/FV924 System

The 70.7V/25V RMS audio input to the HCP must be power limited, such as from the

VCI2001-U1 Amplifier Card.The VCI2001-U1 supervises the audio connection path to

the HCP and provides up to 50 watts of power. The VCI2001-U1 can be wired Style Y

(Class B) or Style Z (Class A). Refer to the VCI2001-U1 Installation Instructions,

Document ID A6V10370410, for further information. In order to function properly

during degrade mode, the periphery FCI2016/2017-U1 to which the HCP is connected

must be located in the same enclosure as the FDNET and VCI2001-U1 that supply

audio to the HCP.

When the HCP is used as a speaker zone, the output speaker lines are only super-

vised when the zone is not active.The audio output must not be allowed to exceed

25 watts.The approximate decibel loss for the total speaker zone wire length for

various wire gauge sizes is shown in Figure 7 for the 70.7V option and in Figure 8 for

the 25V option. Connect the speaker output as Style Z (Class A) or Style Y (Class B) as

shown in Figures 10 and 11.

100

-0.05

-0.10

-0.15

-0.20

-0.25

200 300 400 500 600

TOTAL SPEAKER ZONE WIRE LENGTH (FEET)

dB LOSS

700 800 900 1000

SPEAKER LOAD: 25 WATTS AT 70.7V RMS

LOCATED AT END OF RUN

DOES NOT INCLUDE ANY LOSS

IN RISER RUN

APPROXIMATE SPEAKER ZONE WIRE LOSS

IN DECIBELS FOR VARIOUS GAUGE WIRES VERSUS

TOTAL SPEAKER ZONE WIRE LENGTH (FEET),

WHICH IS TWICE THE WIRE RUN LENGTH.

18 AWG

16 AWG

HCP USED FOR 70.7V RMS OPTION

100

-.5

-1.0

-1.5

-2.0

-2.5

200 300 400 500 600

TOTAL SPEAKER ZONE WIRE LENGTH (FEET)

dB LOSS

700 800 900 1000

SPEAKER LOAD: 25 WATTS AT 25V RMS

LOCATED AT END OF RUN

DOES NOT INCLUDE ANY LOSS

IN RISER RUN

APPROXIMATE SPEAKER ZONE WIRE LOSS

IN DECIBELS FOR VARIOUS GAUGE WIRES VERSUS

TOTAL SPEAKER ZONE WIRE LENGTH (FEET),

WHICH IS TWICE THE WIRE RUN LENGTH.

18 AWG

16 AWG

14 AWG

HCP USED FOR 25V RMS OPTION

Figure 7 Figure 8

Approximate Speaker Zone Wire Loss — 70.7V Option Approximate Speaker Zone Wire Loss — 25V Option

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-138

Figure 9

HCP Used On An XLSV As A 70.7V/25V Speaker Zone

POSITIVE AND NEGATIVE

GROUND FAULT DETECTED

AT <500 OHMS FOR

TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

SUPERVISED

RISER EARTH

SHIELD

HCP

HCP DC SUPPLY FROM

PSC-12 (TB3), PSX-12 (Tb3),

OR PAD-4* (TB16)

FROM DLC

DEVICE LOOP

IN CC-5 / CC-2

POWER LIMITED

70.7V/25V RMS SPEAKER UNITS:

SEE COMPATABILITY GUIDE

P/N 315-096363 FOR LIST OF

COMPATABLE SPEAKERS.

DC INPUT RATING

18.8-28.2VDC, 30mA

FILTERED FULL WAVE

SUPERVISED BY HCP MODULES

NFPA STYLE Y

AUDIO RISER CONNECTIONS

SUPERVISORY: 14 VDC, 1mA

AUDIO OUTPUT: 70.7/25 VRMS,

40 WATTS MAX

POWER LIMITED

STYLE Z

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

24K, W, +/-5%½

EOL RESISTOR

P/N 140-034677

EARTH

SHIELD

HCP

STYLE Y

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

CAPACITOR COUPLED

70.7V/25V RMS SPEAKERS

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677 EARTH

SHIELD

HCP

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677

68K, 1/4W, +/-5%

EOL RESISTOR

ON LAST HCP

SPEAKER ZONE

DEVICE

P/N 140-034728

ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.

12345678

910111213141516

ZAC-40 LOCATED IN ONE

SLOT OF CC-5/CC-2

654321 654321 654321

123456 123456 123456

LINE 1

LINE 2

PROGRAMMING

POINTS

PROGRAMMING

POINTS

PROGRAMMING

POINTS

68K, 1/4W, +/-5%

EOL RESISTOR

P/N 140-034728

*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF

SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”.

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-139

Figure 10

HCP Used On An FV2025/2050 or FV922/924 As A 70.7V/25V Speaker Zone - Class A

POSITIVE AND NEGATIVE

GROUND FAULT DETECTED

AT <500 OHMS FOR

TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

EARTH

SHIELD

HCP

HCP DC SUPPLY FROM

AUX POWER (X1001)

ON PERIBOARD

FC2016/2017-U1,

OR PAD-4* (TB16)

FROM PERIPHERY

BOARD FCI2016/2017-U1

DETECTOR CIRCUITS

POWER LIMITED

70.7V/25V RMS SPEAKER UNITS:

SEE COMPATABILITY GUIDE

P/N 315-096363 FOR LIST OF

COMPATABLE SPEAKERS.

DC INPUT RATING

18.8-28.2VDC, 30mA

FILTERED FULL WAVE

SUPERVISED BY HCP MODULES

NFPA STYLE Y

AUDIO RISER CONNECTIONS

SUPERVISORY: 14 VDC, 1mA

AUDIO OUTPUT: 70.7/25 VRMS,

50 WATTS MAX

POWER LIMITED

STYLE Z

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

24K, W, +/-5%½

EOL RESISTOR

P/N 140-034677

EARTH

SHIELD

HCP

STYLE Y

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

CAPACITOR COUPLED

70.7V/25V RMS SPEAKERS

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677 EARTH

SHIELD

HCP

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677

ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.

VCI2001-U1 AMPLIFIER

LOCATED IN ONE AMPLIFIER

SLOT OF VCA2002-U1

CARD CAGE

654321 654321 654321

123456 123456 123456

LINE 1

LINE 2

PROGRAMMING

POINTS

PROGRAMMING

POINTS

PROGRAMMING

POINTS

68K, 1/4W, +/-5%

EOL RESISTOR

P/N 140-034728

*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF

SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”. THIS

IS IN REFERENCE TO TERMINALS 2 AND 3 ON TB2.

1234

NOTE: EARTH GROUND MUST

BE CONNECTED FOR PROPER

GROUND FAULT DETECTION

LINE 4

LINE 3

IF CLASS A

WIRING

SUPERVISED BULK

AUDIO RISER

Siemens Industry, Inc.

Building Technologies Division

P/N 315-034860-1310

Figure 11

HCP Used On An FV2025/2050 or FV922/924 As A 70.7V/25V Speaker Zone - Class B

POSITIVE AND NEGATIVE

GROUND FAULT DETECTED

AT <500 OHMS FOR

TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

POSITIVE AND NEGATIVE GROUND FAULT DETECTED

AT <500 OHMS FOR TERMINALS 3-6 ON TB1.

EARTH

SHIELD

HCP

HCP DC SUPPLY FROM

AUX POWER (X1001)

ON PERIBOARD

FC2016/2017-U1,

OR PAD-4* (TB16)

FROM PERIPHERY

BOARD FCI2016/2017-U1

DETECTOR CIRCUITS

POWER LIMITED

70.7V/25V RMS SPEAKER UNITS:

SEE COMPATABILITY GUIDE

P/N 315-096363 FOR LIST OF

COMPATABLE SPEAKERS.

DC INPUT RATING

18.8-28.2VDC, 30mA

FILTERED FULL WAVE

SUPERVISED BY HCP MODULES

NFPA STYLE Y

AUDIO RISER CONNECTIONS

SUPERVISORY: 14 VDC, 1mA

AUDIO OUTPUT: 70.7/25 VRMS,

50 WATTS MAX

POWER LIMITED

STYLE Z

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

24K, W, +/-5%½

EOL RESISTOR

P/N 140-034677

EARTH

SHIELD

HCP

STYLE Y

SUPERVISED SPEAKER ZONE CONNECTIONS

SUPV: 14 VDC, 1mA

ACTIVATED: 70.7 V/25V RMS, 25 WATTS MAX

CAPACITOR COUPLED

70.7V/25V RMS SPEAKERS

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677 EARTH

SHIELD

HCP

24K, W½, +/-5%

EOL RESISTOR

P/N 140-034677

68K, 1/4W, +/-5%

EOL RESISTOR

ON LAST HCP

SPEAKER ZONE

DEVICE

P/N 140-034728

ALL WIRING MUST COMPLY WITH NATIONAL AND LOCAL CODES.

VCI2001-U1 AMPLIFIER

LOCATED IN ONE AMPLIFIER

SLOT OF VCA2002-U1

CARD CAGE

654321 654321 654321

123456 123456 123456

LINE 1

LINE 2

PROGRAMMING

POINTS

PROGRAMMING

POINTS

PROGRAMMING

POINTS

68K, 1/4W, +/-5%

EOL RESISTOR

P/N 140-034728

1234

SUPERVISED BULK

AUDIO RISER

IF CLASS A

WIRING

NOTE: EARTH GROUND MUST

BE CONNECTED FOR PROPER

GROUND FAULT DETECTION

*REFER TO PAD-4 INSTALLATION INSTRUCTIONS, P/N 315-050217, FOR PROPER SETTING OF

SWITCH 4. THE AUXILIARY POWER OUTPUT MUST BE CONFIGURED TO “ALWAYS ON”. THIS

IS IN REFERENCE TO TERMINALS 2 AND 3 ON TB2.

LINE 4

LINE 3

Table of contents

Other Siemens Control Unit manuals

Siemens

Siemens XLD-1 User manual

Siemens

Siemens SINUMERIK 840C Manual

Siemens

Siemens SIRIUS ACT 3ZX1012-0SU14-1KA1 User manual

Siemens

Siemens SINUMERIK 828D Turning Owner's manual

Siemens

Siemens simatic ET 200MP User manual

Siemens

Siemens SIMATIC FM 350-2 User manual

Siemens

Siemens Simatic S5 IP 240 User manual

Siemens

Siemens TMM-1 User manual

Siemens

Siemens SIPROTEC 6MU805 User manual

Siemens

Siemens SINUMERIK 840D sl Owner's manual

Siemens

Siemens ZAM-180 User manual

Siemens

Siemens SIMATIC ET 200SP User manual

Siemens

Siemens SIMATIC ET 200S IM151-1 FO STANDARD User manual

Siemens

Siemens SIMADYN D User manual

Siemens

Siemens SIMATIC User manual

Siemens

Siemens SIMATIC CPU 1515SP PC2 F User manual

Siemens

Siemens HOTEL SOLUTION HTC3.2 Series User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SINUMERIK 808D User manual

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 User manual

Siemens

Siemens FMT-A-ADPT User manual

Siemens

Siemens SIM-16RC User manual

Siemens

Siemens SIRIUS User manual

Siemens

Siemens SIMATIC S5 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual