Siemens PS-35 User manual

Installation Instructions

Model PS-35

Power Supply Module

ModelTC-30U

Transfer Module

P/N 315-085062-9

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

Operation

The Model PS-35 stepdown transformer and bridge from

Siemens Industry, Inc. provides a rectified, full wave 24

VDC output from an input supply of 120 VAC, 50/60 Hz.

The input power consists of a main phase, with an inde-

pendent circuitbreaker labeled Reset, and a trouble

phase, which is separately fused. Both inputs use a com-

mon neutral.

The 24 volt full wave output is rated at 9 amperes DC, full

load, and 6 amperes DC, standby load. Separate output

fuses are provided for both the main and

auxiliary power outputs, fused at 15 amps and 2 amps,

respectively.

Terminals 5 and 6 provide 1.5A auxiliary output when the

PS-35 is used as a CP-35 system supply. For example,

output is rated 24 VDC, 1.5A max for internal applications

such as SR-32, SR-33, or Model RA annunciator located

within control unit enclosure(s).

When used as a separate 24 VDC power supply with bat-

tery backup and jumper plug JP-PS, terminals 5 and 6

may provide the full 9A loading. Typical wiring when used

with the TC-30U is shown in the illustration on the back of

this sheet.

Surge protection is provided across both the input

phases as well as the DC output.

Installation

When Used as Power Supply for Control Panel CP-35:

1. Mount the module to the horizontal mounting

brackets in upper right-hand position, on the top row

of the control enclosure.

2. Install wiring as necessary. Use special plug and

harness assembly for connection to CP-35

Control Panel. Refer to CP-35 Wiring Diagram (315-

084902) in the Control Panel INSTALLATION AND

MAINTENANCE INSTRUCTIONS for system inter-

connections.

3. Install protection cover plate over the terminals

after making wiring connections.

When Used as 24 VDC Power Supply with Battery Backup:

(See TYPICAL WIRING DIAGRAM illustration on reverse.)

1. Mount the module to the horizontal mounting

brackets in the control enclosure. Select a

convenient location so that wiring runs are as short

as possible. Note that the PS-35 occupies three

module positions.

2. Connect wiring as necessary.

Note: When an additional PS-35 Power Supply with

jumper plug JP-PS is used for extra bell ringing

capability in a CP-35 controlled system with

emergency power, a transfer module Model

TC-30U is required to supply emergency power

to the audible signal circuit. When battery

backup is not provided, the PS-35 output should

be supervised (SR-30 or equal).

3. Install protection cover plate over the terminals

after making wiring connections.

Fuse Replacement

Remove all system power before replacing fuses, first

battery and then AC. To power up, connect AC first then

battery.

PS-35:

For fuses F2 and F3, slide fuse off fuse holders, then

snap in new fuses.

F2: P/N 105-224090, 15A @ 250V max

F3: P/N 105-284845, 2A @ 125V max

TC-30U:

Push in and turn counterclockwise. Remove fuse from cap.

Replace with P/N 105-224090, 15A @ 250V max.

P/N 315-085062-9

PS-35

TB1

123456

Ground Wire

Connection

Input

Neutral

No Connection

18-31VDC, Full Wave

Unfiltered Rectified

PS-35 9A Max

Special Application

123456

Battery Input

24 VDC, 9A Max

(See Note)

To Designated Load

BATTERY

TROUBLE

TC-30U

15A

JP-PS

120VAC

50/60Hz

PS-35 3.2A

18-31VDC, Full Wave

Unfiltered Rectified or

Battery Backup

PS-35 9A Max

Special Application

Note: Battery charging connections not shown.

TYPICAL WIRING DIAGRAM

When Used As Separate 24 VDC

Power Supply With Battery Backup

When Used As Power Supply

For Control Panel of CP-35

See CP-35 Wiring

Diagram, P/N 315-084902

Notes:

1. Refer to the BI-35 Installation Instructions, P/N 315-086257, for detailed wiring

information when using the PS-35 in conjunction with the BI-35 module.

2. Refer to P/N 315-093680 for all power limited connections.

3. Refer to P/N 315-050769 for all battery information and battery charger information.

4. For the PS-35, TB1 positions 1, 2, 4-6 are non-power limited terminals. If power limited

wiring is desired for terminals 5 and 6, use the PLM-35, P/N 315-093495. For the TC-30U,

all terminals are non-power limited. For power limited wiring on terminals 5 and 6, use

the PLM-35, P/N 315-093495.

This manual suits for next models

Other Siemens Control Unit manuals

Siemens

Siemens SIMOTION D4 5 Series User manual

Siemens

Siemens ZN-31U User manual

Siemens

Siemens SINUMERIK MC Quick start guide

Siemens

Siemens Modem Block User manual

Siemens

Siemens LMS14 User manual

Siemens

Siemens SINUMERIK 828D Turning Owner's manual

Siemens

Siemens EVG4U10E Series User manual

Siemens

Siemens RUGGEDCOM ROS User manual

Siemens

Siemens SINUMERIK 840D Parts list manual

Siemens

Siemens SINAMICS V60 User manual

Siemens

Siemens HLIM User manual

Siemens

Siemens 6ES5-424 Product manual

Siemens

Siemens multiranger 200 User guide

Siemens

Siemens SIMATIC ET 200SP HA User guide

Siemens

Siemens S7-1500 PROFIBUS User manual

Siemens

Siemens SIMOTION D4 5-2 Series User manual

Siemens

Siemens VALVEGYR LDU11.323A17 User manual

Siemens

Siemens LFL Series Owner's manual

Siemens

Siemens SINUMERIK 840D sl Quick start guide

Siemens

Siemens Synco RMZ792 Operator's manual

Siemens

Siemens SIMATIC FM 456-2 Assembly Instructions

Siemens

Siemens 3RA2816-0EW20 User manual

Siemens

Siemens SIMATIC S5 User manual

Siemens

Siemens SINUMERIK 808D User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual