Siemens XMS-SP User manual

OPERATION

The XMS-S, XMS-D, and XMS-M manual stations operate with

the Desigo Fire Safety Modular/Cerberus PRO Modular via the

XDLC. These devices can be wired in either Isolation Mode or

Polarity Insensitive Mode Wiring). The XMS-S/XMS-M manual

station front cover has a recess pocket to pull down and locks in

position after the alarm is initiated. The XMS-D manual station

has an additional lever labeled “PUSH HERE THEN” to get

access to the front cover pocket to initiate the alarm.

Resetting the Manual Station

To reset the stations, insert the Siemens T45 key provided into

the key lock and turn the key 10-15 degrees counter-clockwise as

the arrow shows. The cover will move upward to the normal

position. Rotate the key clockwise and remove key from the lock.

At Normal position the top of the Cover is flush with the top

surface of the Base. Reset the Fire Alarm Control Panel to clear

the alarm.

LED

Diagnostic LED provides visible indication of the manual station

status.

Normal: Green, LED flashes

Alarm: Red, LED flashes

Trouble: Amber, LED flashes. This will happen when the Front

Cover is removed from the Manual Station.

NOTES:

1. Recommended wire sizes: 18 AWG minimum, 14 AWG

maximum.

2. When using shielded cable with or without metal

raceway, the shields must be grounded solely at the

point of origin, for example, at the control panel.

WIRING

Figure 1

Figure 2

Isolator Mode Wiring

Figure 3

Polarity Insensitive Mode Wiring

Single/Dual Action Manual Pull Stations

The Model XMS-S is a single action pull station in a plastic

housing that requires one action by the user to initiate the alarm.

The Model XMS-D is a double action pull station in a plastic

housing that requires two actions by the user to initiate an alarm.

The Model XMS-M is a single action pull station in a metal

housing that requires one action by the user to initiate the alarm.

These models are field installed addressable devices containing

advanced control panel communication technology. This

technology, which provides two-direction communication with the

control panel, produces an Intelligent Initiating Device.

Programming Instructions

Refer to Figure 1 to locate the programming holes which are

accessible through the rear cover.

CAUTION: To prevent potential damage to the DPU DO NOT

connect an XMS to the DPU until the wire at terminal 1 is

removed. Follow the instructions in the DPU Manual, P/N

315-033260, to program the XMS to the desired address.

Record the device address on the label and attach it to the top

surface of the base. The XMS can now be installed and wired to

the system as shown in Figures 2, 3, and 4.

Programming Holes Location

A6V11856080_enUS_a

Programming

Holes

Rear Cover

Line+

Line- From control panel or

previous addressable device

To next addressable

device

Line-

Line+

Line 2

Line 1 From control panel or

previous addressable

device

To next addressable

device

Line 2

Line 1

firealarmresources.com

Specifications

Operating Voltage Range: 13-32 Vdc

Max average operating current @ 24v: 500µA

Operating temperature range: 32 TO 120 F (0 TO 49 C)

Operating humidity range: 0 to 95 % RH

Construction: High impact polycarbonate plastic

Construction: Aluminum

Shipping weight: 1.0 lbs.

Dimensions: 5.50” H x 4.0” W x 1.250” D

ADA Compliant

Compatible electrical boxes: 2-1/2” deep 1-gang box

Optional Accessories

Surface mounted box, P/N S54321-F20-A1

Adapter plate for the existing SB-5R Surface mounted boxes P/N

S54321-F21-A1

Adapter plate for 4” square boxes and 2-gang boxes P/N

S54321-F22-A1

Carton Contents

1. Manual station

2. Two mounting screws

3. One Siemens T45 key

4. Installation Instructions

Installing the manual station

The XMS series manual stations are shipped fully assembled

from the factory.

Installation Instructions:

1. Remove the cover. Insert the Siemens T45 key

provided into the key lock and rotate key 90 degrees

counter-clockwise. Remove the key. The cover can

now be removed.

2. Make all wiring connections as shown in the wiring

diagrams Figure 2 or 3.

3. Using the two 6-32 x ½” machine screws provided

mount the manual station base to the electrical box.

CAUTION: Use very low torque to prevent the

base from becoming distorted. If the base is

distorted, the front cover will not operate. If this

happens, remove cover and loosen the mounting

screws accordingly.

4. Replace the cover: Place the cover inside the base,

insert the key back into the lock and rotate key

clockwise 90 degrees to move the cam down to lock

the cover in place and push cover down until is flush

with the top surface of the base. Remove the key. The

manual station is in normal operating position.

5. To test: Pull cover down to alarm position then check

to see if the cover is locked down. Insert the key to

reset. The cover should move back to normal

position.

Figure 4

Mounting the XMS Series

A6V11856080_enUS_a

FRONT COVER

KEY LOCK ASSY

BASE COMPATIBLE

ELECTRICAL

1-GANG BOX

LED LIGHT PIPE 6-32 X1/2 SCREWS

(2) PLACES

CAUTION: Do not overtighten the screws.

Overtightening may distort the Base.

firealarmresources.com

Cyber security disclaimer

Siemens provides a portfolio of products, solutions, systems and services that

includes security functions that support the secure operation of plants, systems,

machines and networks. In the field of Building Technologies, this includes building

automation and control, fire safety, security management as well as physical

security systems.

In order to protect plants, systems, machines and networks against cyber threats, it

is necessary to implement –and continuously maintain –a holistic, state-of-the-art

security concept. Siemens’ portfolio only forms one element of such a concept.

You are responsible for preventing unauthorized access to your plants, systems,

machines and networks which should only be connected to an enterprise network

or the internet if and to the extent such a connection is necessary and only when

appropriate security measures (e.g. firewalls and/or network segmentation) are in

place. Additionally, Siemens’ guidance on appropriate security measures should be

taken into account. For additional information, please contact your Siemens sales

representative or visit https://www.siemens.com/global/en/home/company/topicareas/

future-of-manufacturing/industrial-security.html.

Siemens’ portfolio undergoes continuous development to make it more secure.

Siemens strongly recommends that updates are applied as soon as they are

available and that the latest versions are used. Use of versions that are no longer

supported, and failure to apply the latest updates may increase your exposure to

cyber threats. Siemens strongly recommends to comply with security advisories on

the latest security threats, patches and other related measures, published, among

others, under https://www.siemens.com/cert/en/cert-security-advisories.htm.

A6V11856080_enUS_a

firealarmresources.com

Document ID A6V11856080_enUS_a P/N A5Q00072530

firealarmresources.com

This manual suits for next models

Other Siemens Computer Hardware manuals

Siemens

Siemens SIMATIC S7-1200 CP 1243-8 IRC User manual

Siemens

Siemens SIMATIC CP 341 User manual

Siemens

Siemens LMV50 series User manual

Siemens

Siemens SIMATIC NET CP 5614 A2 User manual

Siemens

Siemens DP/AS-Interface Link 20E User manual

Siemens

Siemens CP 1626 User manual

Siemens

Siemens Gigaset USB adapter 54 User manual

Siemens

Siemens SINUMERIK 808D User manual

Siemens

Siemens Simatic S7-1500 User manual

Siemens

Siemens SIMATIC CP 340 User manual

Siemens

Siemens SED2 Series User manual

Siemens

Siemens Simatic S7-300 Instruction manual

Siemens

Siemens SIMATIC S7 400 User guide

Siemens

Siemens SMP16-CPU06 Series User manual

Siemens

Siemens Simatic 545-1106 User manual

Siemens

Siemens SIMATIC NET CP 443-1 Advanced User manual

Siemens

Siemens Simatic M7-400 User manual

Siemens

Siemens SIMATIC PCS 7 OSx User manual

Siemens

Siemens 928B User guide

Siemens

Siemens SIMEAS-Hub 7KE6000-8AD /CC User manual

Siemens

Siemens PAD-5 Series User manual

Siemens

Siemens SIMATIC CP 541 User manual

Siemens

Siemens SPEEDSTREAM SS1021 User manual

Siemens

Siemens SIMATIC PG 760 Manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

National Instruments

National Instruments PXI-8186 user manual

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual