Siemens CC-5 User manual
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-4
Installation Instructions
Model CC-5
System Cardcage for NCCNT WAN
INTRODUCTION The Model CC-5 Cardcage from Siemens Industry, Inc. (see Figure 1) has five card
slots and occupies two positions on the studs in the backbox or on the optional
CAB-MP Mounting Plate. The CC-5 is used for mounting all system circuit card
assemblies. It has two removable terminal block connectors at the top and one
removable terminal block connector at the bottom of each card slot. All field-wiring
connections are made directly to the top of the cardcage while internal power is
connected to the bottom of the cardcage. The two removable terminal block connec-
tors at the top of each slot are arranged in two rows. The lower row is labeled 1
through 8 and the upper row is labeled 9 through 16. These removable terminal
block connectors are used for connecting power limited external equipment. The
removable terminal block connector located at the bottom of each slot is labeled 17
through 24 and is used for connecting internal power.
Figure 1
CC-5 Card Cage
OPERATION The CC-5 provides a central point for mounting circuit card assemblies. If a card
requires power, it is applied through the removable terminal block at the bottom of
the cardcage. All external devices for the card are connected to the card through the
two removable terminal blocks at the top of the cardcage.The circuit card assemblies
are connected to the HNET bus through the connectors on the cardcage.
PRE-INSTALLATION The CC-5 is shipped with the card guides removed.The card guides are keyed to
assist in installation.They can be installed either before or after the cardcage is
installed in the enclosure. For ease of installation, the card guides have been de-
signed to be installed after the field wiring has been completed.
Note:
Board shown without
card guides installed.
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-42
Card Guide Installation (Figure 2)
The upper and lower card guides are keyed differently and are not interchangeable.
Ensure that the card guide keys fit easily into the holes in the motherboard to
prevent damage.
1. The upper card guide has a label on each slot that can be used to identify
the module installed in the slot. If desired, complete the label before
inserting the upper card guide.
2. Insert the upper card guide and secure with the captive screws.
3. Insert the lower card guide and secure with the captive screws.
GUIDE
PIN
GUIDE PIN HOLE
CAPTIVE SCREW RETAINERS
CAPTIVE SCREWS
LABELS
LOWER CARD GUIDE
UPPER CARD GUIDE
Figure 2
Card Guide Installation
INSTALLATION
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
The CC-5 mounts at the back of the enclosure on the studs in the backbox or on the
optional Mounting Plate (CAB-MP).The Mounting Plate may be located either “IN” or
“OUT” of the enclosure to perform this installation procedure. If the Mounting Plate is
located “IN” the enclosure you will have to gain access to it by opening the enclosure
Inner and Outer doors. If the Mounting Plate is located outside of the enclosure,
place it in front of you so that the word “TOP” is at the top and away from you.
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-43
Each row of studs in the backbox or each Mounting Plate can hold a maximum of
two CC-5 cardcages. There are three possible locations for mounting the CC-5.
1. Flush left in the backbox or on the Mounting Plate in positions 1-2.
2. In the center of the row in the backbox or on the Mounting Plate in posi-
tions 2-3.
3. Flush right in the backbox or on the Mounting Plate in positions 3-4.
When only one cardcage is to be installed, it is normally installed on the left side of
a row or on the Mounting Plate.
There is a top and bottom to the Mounting Plate.The top is where the word “TOP” is
stamped on the Mounting Plate. When the cardcage is mounted correctly on the
Mounting Plate it will be flush on the top, bottom, and left with the Mounting Plate
and the two screw holes in the center of the cardcage motherboard will be over
threaded posts.
1. Install four 10-32 screws in the threaded posts at the top left of Position 1,
top right of Position 2, bottom left of Position 1, and the bottom right of
Position 2 on the Mounting Plate. Screw each of the 10-32 screws into the
threaded posts 5-6 turns. (Refer to Figure 3.)
2. Place the cardcage over the four screws on the Mounting Plate and slide it
down or towards you to rest on the four screws. (Refer to Figure 4.) When
the cardcage is in the correct position it will be flush with the top, bottom,
and left side of the Mounting Plate.
3. Install the two 10-32 screws in the center of the cardcage motherboard near
the left and right edge.
4. Tighten the six screws.
TOP
CC-5 TOP THREADED POSTS
CC-5 BOTTOM THREADED POSTS
POSITION 1 POSITION 3 POSITION 4
POSITION 2
POSITION 1 POSITION 3 POSITION 4
POSITION 2
CAB-MP
Figure 3
Location Of The CC-5 On The Optional CAB-MP
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-44
TOP
SLIDE DOWN CARDCAGE UNTIL
FLUSH ON TOP, LEFT, AND BOTTOM
CAB-MP
CC-5 CARDCAGE
INSTALL TWO 10-32 SCREWS WHEN
ALIGNED WITH THREADED STUDS
WIRING At the top and bottom of the CC-5 and adjacent to each card slot are removable
terminal blocks.The wiring to the two terminal block connectors at the top of the CC-
5 is power limited.The wiring to the terminal block connector at the bottom of the
CC-5 is non-power limited.
To Connect External Wiring
To The Card Slots: (Figure 5)
1. Insert the wire to be connected in the desired opening in the side of the
removable terminal block.
2. Tighten the appropriate locking screw.
Figure 4
Mounting The CC-5 On The Optional CAB-MP
Figure 5
Removable Terminal Block On The CC-5
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-45
To Connect The
Data Bus: The Data bus connectors on the cardcage motherboard are P1 and P2. (Refer to
Figure 6.)They are 60 pin, keyed, male connectors with connector extractors.
1. Open the connector ejectors out of the vertical position and away from the
connector body.
2. Insert the female cable connector into the male connector (P1 or P2) on the
cardcage motherboard. Gently press the cable connector into the
motherboard connector. As the cable connector is pressed in, the connector
ejectors will begin to move to the vertical position. When the cable connec-
tor is fully seated the connector ejectors will be vertical.
CONNECTOR EJECTORS
IN VERTICAL POSITION
SPECIFICATIONS Physical Specifications: 10.58”W x 14.25”H
Electrical Ratings: The PSC-12 supplies the power to the two 60-pin Data
bus connectors (P1 and P2) in the CC-5.The total
rating for all CC-5s in any given enclosure is as follows:
24 VDC, 2 Amps max
6.2 VDC, 2 Amps max
See PSC-12 Installation Instructions, P/N 315-099321, and the PSX-12 Installation
Instructions, P/N 315-048553, for complete power supply loading calculations.
Figure 6
Location Of Connectors On The CC-5
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-46
This page was left intentionally blank.
Siemens Industry, Inc.
Building Technologies Division
P/N 315-099319-47
This page was left intentionally blank.
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
P/N 315-099319-4
Table of contents
Other Siemens Computer Hardware manuals
Siemens
Siemens SIMATIC NET CP 5603 User manual
Siemens
Siemens Simatic S7-1500 User manual
Siemens
Siemens Simatic M7-400 User manual
Siemens
Siemens Fujitsu D1159 User manual
Siemens
Siemens SIMATIC NET 6GK7 443-5FX02-0XE0 User manual
Siemens
Siemens SIMATIC NET CP 1411 User manual
Siemens
Siemens SIMOTION TB30 User manual
Siemens
Siemens SIMATIC CP 340 User manual
Siemens
Siemens Gigaset PC Card 108 User manual
Siemens
Siemens SED2 Series User manual
Siemens
Siemens SIMATIC CP 340 User manual
Siemens
Siemens CP 5613 A3 User manual
Siemens
Siemens SIMATIC NET CP 1623 User manual
Siemens
Siemens PAD-5 Series User manual
Siemens
Siemens CP 443-1 User manual
Siemens
Siemens SIMATIC S7-400 CP 440 User manual
Siemens
Siemens SIMATIC NET CP 5603 User manual
Siemens
Siemens SIMATIC S7 400 User guide
Siemens
Siemens SIMATIC S7-1200 User manual
Siemens
Siemens SIMATIC PG 760 Manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
