Sharp PN-L602B User manual

PN-TPC2W7A

User Guide

Version –1

Getting Started

Introduction to PN-TPC2W7A

The PN-TPC2W7A is a full-featured High Definition PC based upon Intel

H67®architecture, and powered by an Intel®G620 Pentium®Dual-

core CPU. Targeted for Commercial applications such as interactive

digital signage, the PN-TPC2W7A has been optimized for reliable

operation with Sharp® PN-L series touch-screen displays. The PN-

TPC2W7A includes the Sharp Pen Software™application pre-installed

on the hard disk. It also has the flexibility to run most third party

software and custom applications. The PN-TPC2W7A supports true

1080P video with hardware assisted support for formats such as

MPEG2, H.264 and WM9. The PN-TPC2W7A was designed with display

integration in mind and features a full complement of video outputs

including HDMI®and DVI. The unit also includes an RS232 port for

display control and a custom mounting bracket specially designed to

attach behind a Sharp PN-L series touch screen display. The PN-

TPC2W7A’s all metal chassis and small size make it ideal for

commercial applications requiring a powerful yet compact PC.

Package Contents

The packing box should contain the following

items:

Technovare™PN-TPC2W7A

AC Power Adapter

Mounting Kit

HDMI Cable

Connection Diagram

This Users Guide

Getting Started

Federal Communications Commission (FCC)

Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with instructions contained in

this manual, may cause harmful interference to radio and television

communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and the receiver

Connect the equipment into an outlet on a circuit different from that of the

receiver

Consult the dealer or an experienced audio/television technician

NOTES:

Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result in

harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly approved by

the party responsible for compliance could void the user’s authority to operate this

equipment. To ensure that the use of this product does not contribute to

interference, it is necessary to use shielded I/O cables.

Getting Started

Specifications

Chipset

oIntel®H67

Size

oMini-ITX form factor

oCase: 7.5x 7.4x 1.75

Microprocessor support

oIntel®G620 2.6 GHz Pentium®Dual-Core CPU

Operating systems:

oSupports Windows®XP®32bit/64bit, Windows Vista®

32bit/64bit, and Windows®7®32bit/64bit

oSupports Linux®

oWindows 7 Pro installed

Software Installed:

oSharp®Pen Software™Application

oMicrosoft®Internet Explorer®

oMicrosoft PowerPoint®Viewer

oWindows Media®Player

oQuickTime®Player

oAdobe®Flash® Player Plug-in

System Memory support

oSupports DDR3 1333/1066

oSupports up to 16GB (2 x 8GB)

o2GB installed –both slots occupied and need to remove

the current memory modules to upgrade

USB 2.0 Ports

oSupports hot plug and play

oFour USB 2.0 ports (rear panel ports)

oTwo onboard USB headers for four extra ports

oSupports USB 2.0 protocol up to 480 Mbps transmission

rate

Hard Disk Drive

o2.5” 160GB SATA

Onboard Serial ATA II/III

oSupports 1x SATA II (300 MB/s transfer rate)

oSupports 2x SATA III (600 MB/s transfer rate)

oRear panel e-SATA

oSupports hot plug and Native Command Queuing

On board Realtek 8111E Gigabit LAN Chip

oSupports 10/100/1000Mbps operation

o1 x RJ45 LAN Port

Specifications

Specifications (con’t)

Onboard Audio

oRealTek™ ALC888S High-Definition audio chip

oSupports up to 8-channel (2/4/5.1/7.1-channel)

o8-Channel Audio Ports on Back Panel

oSupports Jack-Sensing function (under Windows)

oSupport for S/PDIF Out Header (Internal)

Green Function

oSupports ACPI (Advanced Configuration and Power

Interface)

oSupports EuP Function

oRTC timer to power-on the system

oAC power failure recovery

oSupports S0 (normal), S1 (power on suspend), S3

(suspend to RAM), S4 (suspend to disk), and S5 (soft - off)

Onboard Graphics support

oIntegrated Intel®GMA HD graphics engine

oDVI-I / HDMI®output support (Dual Header capable)

Integrated HDMI Interface with HDCP

oSupports DVI or HDMI 1.4 interfaces

oSecure digital audio merged from integrated HDA codec

with no external audio signals required

oSupport for HDCP 1.3 using soft or hard HDCP keys

oHDCP encryption support when configured as DVI or HDMI

link without the need for external HDCP key crypto ROM

Dual Head Display Controller

oEach controller can drive same or different display

contents to different resolutions and refresh rates

Expansion Slots

o1 x PCIe 2.0 x16 slot

o1 x COM1 Header

oLow power consumption and power management features

Optional

oWatchdog timer

Environmental

oOperating Temperature: 0° to 40° C

oOperating Humidity: 80% maximum relative humidity,

non-condensing

Power

oInput Voltage: 12V 7A

oPower Dissipation: 84 Watts

Installation

Mounting PN-TPC2W7A on Sharp PN-L Series

Displays

1. Before mounting, make sure to turn off the monitor

and remove the AC power.

2. Items needed

Sharp PN-L Series Touch-

Screen Display

PN-TPC2W7A

Mounting Plate

AC Power Adapter

4 x M4 (0.7x10mm) screws

2 x M3 (0.5x5 mm)

Phillips®Screw Driver

3. Attach the mounting plate

There are 8 holes on the

mounting plate, but only use 4

holes to match the monitor’s

mounting holes depending on the

monitor model.

The mounting plate is attached to

the Sharp “PN-L” series display as

in Figure 2.

Secure the mounting plate to the

monitor with four included M4 screws.

*NOTE- Do not use the holes marked with the red x

Figure 1

Figure 2

Installation

4. Set the AC power adapter in

place

Place the AC power adapter into

the holder on the right side of

the mounting plate as in Figure

AC power cord faces downward

and the DC power cord to the

PN-TPC2W7A faces upward.

5. Install the PN-TPC2W7A

If you look at the right side of the

PN-TPC2W7A before sliding it into

the mounting plate as in Figure 4,

there are two small slits near the

edges on the PN-TPC2W7A and

two small fingers on either side of

AC power adapter holder on the

mounting plate.

As you slide the PN-TPC2W7A

into the mounting plate, insert

the two fingers into these slits as

in Figure 5.

Figure 4

Figure 3

Figure 5

Installation

There are two fingers on the left

side of the mounting plate to

catch the PN-TPC2W7A in place

as shown in Figure 6, and they

need to be tightened with two

include M3 screws.

6. Connect the HDMI video cable and the

USB cable prior to turning on the PN-

TPC2W7A.

7. Finish

Plug in the DC power cord into

the PN-TPC2W7A’s power

connector as in Figure 7.

Figure 7

Figure 6

Installation

Rear Connector Layout

Audio Port 2-Channel 4-Channel 5.1-Channel

Blue Line-In Line-In Line-In

Green Line-Out Front Speaker Out Front Speaker Out

Pink Mic In Mic In Mic In

Orange N/A N/A Center/Subwoofer Out

Black N/A Rear Speaker Out Rear Speaker Out

Grey N/A N/A N/A

Audio Port 7.1-Channel

Blue Line-In

Green Front Speaker Out

Pink Mic In

Orange Center/Subwoofer Out

Black Rear Speaker Out

Grey Side Speaker Out

LAN Connector (with LED status indicator)

Green/Light Up/Blink = 10 Mbps/Link/Activity

Green and Green/Light Up/Blink = 100 Mbps/Link/Activity

Green and Orange/Light Up/Blink = 1000 Mbps/Link/Activity

Installation

Rear Connector Layout (con’t)

1. Power Connection (refer to the Rear Connector Layout on pg. 8)

Use only the AC power adapter supplied with the system.

Input: 100~240V AC 1.3A

Output: 12V DC 7A

Plug the 12V AC/DC adapter (as in the figure 1 above) to the PN-

TPC2W7A’s power input jack (as in the figure 2).

2. Power Button

This button will stay lit if the PN-TPC2W7A is powered on. If the

PN-TPC2W7A doesn’t power up after the AC is connected, then

press this button to power up. If normal Windows shutdown is

not shutting down the PN-TPC2W7A, then press this button for

more than 4 seconds will turn off the PN-TPC2W7A. In this case,

run Disk Cleanup in Windows next time the PN-TPC2W7A is

powered up.

Other manuals for PN-L602B

This manual suits for next models

Table of contents

Popular Desktop manuals by other brands

HP m9060n - Pavilion - Elite Quick setup

Asus

Asus E210 Series user guide

Dell

Dell Inspiron 600m quick start

Dell

Dell Inspiron 3662 Service manual

TotalFlow

TotalFlow uFLO user manual

HP Presario SV7000 - Desktop PC manual

HP ProDesk 400 G5 Maintenance and service guide

Logitech

Logitech MK320 quick start guide

Dell

Dell XPS 730 H2C Service manual

Sony

Sony Vaio Series operating instructions

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer quick start

Alto

Alto MD 250 instruction manual

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series user manual

Sony

Sony VAIO VGX-TP1 Series user guide

Asus

Asus Eee Box B204 user manual

Dell

Dell Optiplex 9010 All In One owner's manual