Sharp AF-S155NX User manual

AF-S155NX

Please read ALL instructions before installing. Two people are

recommended to install this product. If a new electrical outlet

is required, have the outlet installed by a qualified electrician

before installing unit. See#5 in Preliminary Instructions

following.

Preliminary instructions

Do the following before starting to install unit. See illustrations

below.

with this air conditioner are made to install in a wooden

Check dimensions of your unit to determine model type:

1. Check window opening size - the mounting parts furnished

sill double-hung window. The standard parts are for

window dimensions listed above. Open sash to a minimum

of 19"(483mm). (FIG. 1)

2. Check condition of window - all wood parts of window

must be in good shape and able to firmly hold the needed

screws.If not, make repairs before installing unit.

3. Check your storm windows - if your storm window

frame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG.2, or by removing

storm window while room air conditioner is being installed.

(continued)

Unit Height:

Unit Width:

Min. Window Opening:

Min. Window Width:

Max. Window Width:

17.5/8"

23 1/2"

18 1/2"

26 1/2"

40 1/2"

FIG. 1 FIG. 2

SASH

19" MIN

1/2" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

SASH

1/2" MIN

19" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

1 1/2" MIN

BOARD THICKNESS AS

REQUIRED, ALONG

ENTIRE STOOL, FASTEN

WITH TWO NAILS OR

SCREWS.

SEAL-BOTTOM RAIL TO UNIT

SIDE RETAINER

FRAME

ASSEMBLY

(LEFT)

WASHER HEAD

LOCKING SCREW

FOAM GASKET

TOP ANGLE

FRAME

ASSEMBLY

(LEFT)

SAFETY LOCK AND

3/4" LONG HEX HEAD

SCREW

1/2" LONG

SCREWS AND

LOCKNUTS

LOCKNUT

3/4" LONG

FLAT HEAD

BOLT

WINDOW SUPPORT

BRACKET

WINDOW SASH SEAL

SILLANGLE

BRACKET

4. CHECK FOR ANYTHING THAT COULD BLOCK

AIRFLOW - check area outside of window for things

such as shrubs, trees, or awnings. Inside, be sure

furniture, drapes, or blinds will not stop proper air flow.

5. Check the available electrical service - power supply must

be the same as that shown on the unit serial nameplate.

Power cord is 48"long. Be sure you have an outlet near.

All models have a 3-prong service plug to provide proper

service and safe positive grouding. Do not change plug in

any way. Do not use an adapter plug. If your present wall

outlet does not match your plug, call a qualified electrician

to make the needed change.

a large flat blade screwdriver

tape measure

adjustable wrench or pliers

pencil

Level

Socket wrenches

Phillips screwdriver

Tools Required

Hardware (in plastic bag)

6. Carefully unpack air conditioner - remove all packing

material. Protect floor or carpet from damage. Two

people should be used to move and install unit.

Avoid fire hazard or electric

shock. Do not use an extension cord or an

adaptorplug.Donotremoveany prong from

the power cord.

WARNING

Grounding type wall

receptacle

Do not, under any

circumustances, cut,

remove, or bypass the

grounding prong.

Power supply cord

with 3-prong grounding

plug and current

detection device

Washer Head

Locking Screw

For window panels

3/4" Long Hex-

Head Screw 3

Qty.

Safety Lock

1/2" Long Screw

and locknut

3/4" Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

4 ea.

2 ea.

Long hex-head

locking screw for

top angle, side

retainer 5/16"

Long

Remove Chassis

Install Top Angle

and Side Bracket

1. Pull down front panel and remove filter. (See FIG. 1).

2. Lift front upwards and place to one side.

1. Attach foam gasket to top angle above holes as

shown in FIG. 6.

3. Locate the four front screws and remove. These screws will

be needed to re-install the front later. (See FIG.2)

4. Pry away front from cabinet sides as per photo (see FIG.3)

5. Gently lift front off unit and place to one side (See FIG.4).

2. Install top

angle and

side retainers

to cabinet as

shown in FIG. 6.

FIG. 6

6. Remove shipping crews from top of unit and also on the side

by the base if installed.

7. Hold the cabinet while pulling on the base handle, and care-

fully remove the unit.

8. Add two foam inserts to holes in top of cabinet where

shipping screws were removed from.

Assemble Window

Filler Panels

1. Place cabinet on floor, a bench, or a table.

2. Slide "I" section of window filler panel into side retainer

on the side of the cabinet (see Figures 7-8). Do both

sides.

FIG. 7

PLASTIC

FRAME

WINDOW FILLER

PANEL

SIDE

RETAINER

FIG. 8

AIR CONDITIONER

CABINET

TOP

VIEW

PLASTIC

FRAME

"I" SECTION WINDOW

FILLER

PANEL

LOCKING

SCREW

HOLE

FIG. 3 FIG. 4

FIG. 1 FIG. 2

3. Insert top and bottom legs of window filler panel frame

into channel in the to angle and bottom rail. Do both

sides.

4. Insert washer head locking screws (2) into holes in

top leg of filler panel frame (see Step 6). Do not totally

tighten. Allow leg to slide freely. Screws will be

tightened after Section 6.

Install Support

5Bracket

1. Hold each support bracket flush against outside of sill,

and tight to bottom of cabinet as shown below. Mark

brackets at top level of sill, and remove.

Place Cabinet in

4Window

1. Open window and mark

center of window stool.

2. Place cabinet in window with bottom stool angle firmly

scated over window stool as shown. Bring window

down temporarily behind top angle to hold cabinet in

place.

STOOL

ANGLE

LEFT

LOCKNUT

SILL ANGLE

BRACKET

FLAT HEAD BOLT

2 EACH REQ'D FOR EACH

SUPPORT BRACKET

MARK

1/2" LONG SCREWS

AND LOCKNUTS

RIGHT

3. Shift cabinet left or right as needed to line up center of

cabinet on center line marked on stool.

4. Fasten cabinet to window stool with 2 screws into

holes.(You may wish to pre-drill pilot holes.)

5. Add bottom rail seal over screws to window stool.

2. Asscmble sill angle bracket to support brackets at the

marked position, as shown. Hand tighten, but allow

for any changes later.

3. Install support brackets (with sill angle brackets

attached) to correct hole in bottom of cabinet as shown.

4. Tighten all 6 bolts securely.

1/2" long screws

and locknuts

Bottom

Rail Seal

3/4" long HEX-

HEAD SCREW

Extend Window Filler

Panels

1. Carefully raise window to expose filler panel locking

1. Lift air conditioner and carefully slide into cabinet

3. Be sure chassis is firmly seated towards rear of cabinet.

4. Installation of front is the reverse of removal outlined

leaving 6" protruding.

in Section 1.

DO not push on controls OR finned coils.

screws. Loosen screws so filler panels slide easily.

2. Extend panels to fill window opening completely.

3. Close window behind top angle.

Tighten locking screws on top.

1. Trim sash seal to fit window width. Insert into space

between upper and lower sashes.

2. Attach right angle safety lock as shown.

LOCKING SCREWS

WINDOW SASH SEAL

SAFETY LOCK

3/4" long hex-

head screw

6Install Chassis into

Cabinet and Install

Front to Unit

Install Window Lock

and Sash Seal

Table of contents

Popular Air Conditioner manuals by other brands

Spheros

Spheros CC 355 instructions

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE owner's manual

Panasonic

Panasonic CS-E12HKEW operating instructions

nedis

nedis ACMB1WT7 quick start guide

Samsung

Samsung AR KV Series User & installation manual

Daikin

Daikin FCFV50A Operation manual

Fujitsu

Fujitsu Inverter ASBA30JFC operating manual

Toshiba

Toshiba RAS-M10SMUV-E installation manual

Daikin

Daikin FXLQ20MAVE Operation manual

Hitachi

Hitachi RAS-E24CAK instruction manual

CIAT

CIAT Magister 2 Series Installation, Operation, Commissioning, Maintenance

Bestron

Bestron AAC6000 instruction manual

Hisense

Hisense 7K Use and Installation Instructions

Frigidaire

Frigidaire FFRE0533S1E0 Use & care guide

Samsung

Samsung AS09HM3N user manual

Frigidaire

Frigidaire CRA073PU11 use & care

Soleus Air

Soleus Air GB-PAC-08E4 operating instructions

McQuay

McQuay MCK020A Technical manual