SEWOO LK-P43 User guide

MODEL:LK-P43

Portable Printer

SEWOO TECH CO.,LTD.

374-2, Gajang-dong, Osan-si, Gyeonggi-do, 447-210, Korea

TEL : +82-31-459-8200 FAX : +82-31-459-8880

www.miniprinter.com

P43 Rev. A 05/13

System Administrator Manual

Table of Contents

1. INTRODUCTION

1-1 Using This Manual 4

1-2 Using the Menu Chart 4

1-3 Using the Display and Buttons 5

1-3-1 Selecting a Menu 6

1-3-2 Exiting a Menu 6

1-3-3 Printing 6

1-4. Selecting a Language 7

2. USING DIAGNOSTICS

2-1 Diagnostics 8

2-1-1 Printer 9

2-1-2 Display 15

2-1-3 Buttons 16

2-1-4 RAM 17

2-1-5 Data Dump 18

2-1-6 About 19

3. SETTING UP THE PRINTER

3-1 SETUP 20

3-1-1 Stock Power 21

3-1-2 Backlight 22

3-1-3 Contrast 23

3-1-4 Printer 24

3-1-5 Serial Communications 36

3-1-6 Power Management 40

4. WI-FI 42

4-1 RF Network 42

4-2 Wi-Fi setting utility instruction 50

4-2-1 Port and Wi-Fi Information Tab 51

4-2-2 Wi-Fi Information Tab 51

4-2-3 WPA Authentication Tab 51

4-3 Using the Web Interface 52

4-3-1 Navigation Bar 53

4-3-2 Status 54

4-3-3 Navigating the Website 55

4-3-4 Conguration 56

4-3-5 Certicates 73

4-3-6 Network 75

4-3-7 Maintenance 76

4-3-8 Updating a Field 79

4-4 Wi-Fi Glossary 80

4-5 Wi-Fi Specications 85

5. BLUETOOTH

5-1 Using the Bluetooth Settings Dialog 86

5-1-1 Enabling the Security 86

5-1-2 Change Pin 87

5-1-3 Local Name 87

5-1-4 Local Address 88

5-1-5 Printing Info 88

5-2 Bluetooth Interface 89

5-2-1 Printer Connection Settings 90

5-2-2 Get Bluetooth Information 91

5-2-3 PIN Code Information 91

5-2-4 Discoverable Mode Information 91

5-2-5 Emulation Settings 92

1. INTRODUCTION

1-1. Using This Manual

1-2. Using the Menu Chart

Subjects Contents

1Introduction Notes before using printer

2Diagnostics How to print test label, check sensor, check print position, etc.

3Setting Up the Printer How to use the Setting Menu to adjust stock

and printer settings

The black boxes show present position, the boxes with a thick line show how you got there.

1-3. Using the Display and Buttons

NOTE

button operates as feed button in ready condition only.

Screen displays Meaning

Selects the highlighted option.

Moves position of Menu upwards by one step.

Moves the cursor to the position to change.

Moves position of Menu downwards by one step

Increases set value

Decreases set value

Display

Enter button

Power button

Up button

Paper Feed /

Down button

Select Exit Menu or press the power ( )button to return to the previous menu

There are three ways to print.

1. When turning on the printer, press and hold the power ( ) button and the Down(▼)

button. The printer prints a batch (if sent) or prints the printer status information.

2. Select a test label from the Diagnostics menu.

3. Send batch data to the printer.

1-3-1. Selecting a Menu

1-3-2. Exiting a Menu

1-3-3. Printing

1. Press Enter( ) button to enter the Menu

2. Move cursor to the menu using Up(▲) / Down(▼) buttons, and select the Menu by

pressing Enter( ) button.

1-4. Selecting a Language

You can read Menu names or messages of the printer in English, French,

Spanish, German.

1. Turn on the printer. The printer name and software version information are displayed.

Then you see

2. Press Enter( ) button.

3. Move cursor to language by pressing Down(▼)button and then press Enter( ) button.

4. Move the cursor to the language you want by pressing Up(▲)/Down(▼) button then

press Enter( ) button.

5. The selected language is displayed on the screen.

6. Select exit to return to the diagnostics menu or press the power button to return to the

ready screen

Communication Communication

Online Diagnostics Online Diagnostics

Diagnostics Diagnostics

Deutsch

Exit

2-1. Diagnostics

This chapter describes how to use Diagnostics in the Tool Box.

You can view test results through this Menu; however, you cannot change the setting.

1. Turn on the printer. The printer name and software version information are displayed.

Then you see

2. Press Enter( ) button and then you see

3. Enter( ) button and you see

5. If correct password is typed in then you see

4. Press Up(▲) and Enter( ) button in the sequence of ,▲, ▲, ▲,

6. Cursor is positioned on the Diagnostics Menu. Enter into Diagnostics Menu by pressing

Enter( ) button.

2. Using Diagnostics

To return to initial screen, press power( )button

Four test labels can be printed: Diagnostic Label, Test Pattern, Gray Scale,

MIF (Monarch Initialization Files) Info

**Test Label

1. Select Printer - Test Label - Diagnostic Label in Diagnostics Menu

2. Select Printer – Test Label– Test Pattern in Diagnostics Menu

Checkerboard pattern is printed

not applicable

2-1-1. Printer

Communication

Online Diagnostics

Setup

Diagnostics

Exit

10 11

Gray Scale printed

not applicable

3. Select Printer - Test Label - Gray Scale in Diagnostics Menu.

4. Select Printer – Test Label – MIF Info in Diagnostics Menu.

In this Menu, you can read each A/D value of the Black Mark, Gap, or Peeler,

Peel-SW sensors. Position of each sensor is as shown in following picture.

**Sensors

1. Load stock in the printer.

PEELER SENSOR

B/M & GAP SENSOR

12 13

2. Select Printer – Sensors – Black Mark in the Diagnostics Menu.

Check whether A/D value is changing in Black Mark sensor position while feeding

Black Mark stock manually.

3. Select Printer – Sensors – Peel in Diagnostics Menu. Check whether A/D value is

changing by covering the Peeler Sensor with stock

Make sure the stock is loaded in line with upper/lower Black Mark sensor.

4. Select Printer – Sensors – Gap in Diagnostics Menu.

Check whether A/D value is changing in Gap sensor position by feeding Gap stock

manually.

5. Select Printer – Sensors – Gap in Diagnostics Menu.

Check whether A/D value is changing by Peeler S/W position.

Peel-SW

A/D Value = 194

With a roll of stock installed, slide the

peeler body towards the back of the printer.

Lift the peeler wing and slide the peeler body

towards the front of the printer.

6. Press Enter( ) button to return to the previous menu.

Back

14 15

1. Select Printer – Printhead – Temperat in the Diagnostics Menu.

1. You can check it in the battery shape located at upper right side of the ready screen.

In this Menu, You can check Printhead temperature(TPH) in ℃(Centigrade) unit.

The temperature of Printhead must be lower than 60℃to print.

Press Enter( ) button to return to the previous menu.

**Printhead

There are two ways to check the battery level.

2. Select Printer – Battery in the Diagnostics Menu Battery level is displayed in

voltage on the screen

**Battery

NOTE

(7.8v above) (7.5v above)

(7.2v above) (6.8v below)

Press Enter( ) button to return to the previous menu.

1. Select Printer – View Total – Print Inch in Diagnostics Menu.

In this Menu, you can view Total inches printed

**View Total

Press Enter( ) button to return to the previous menu.

Remaining electricity of battery

2-1-2. Display

1. Select Display – Backlight in the Diagnostics Menu

You can check the display in this Menu.

2. Press the Up(▲) button Backlight is turned off, if the same button is pressed once more then it

is turned on.

3. Press Enter( ) button to exit from Backlight Test.

4. Select Display – RGB Pattern in the Diagnostics Menu.

5. Press Enter( ) button to exit from RGB Pattern.

Diagnostics Online Diagnostics

Communication

16 17

2-1-3. Buttons

1. Select Keyboard in Diagnostics Menu.

2. Press the upper left Up(▲) button, press the Down(▼) button, and press Enter( ) button.

3. Each should change from O shape to X shape when pressed.

4. Press Enter( ) button to from keyboard test.

2-1-4. RAM

Select this Menu and check memory of the printer.

1. Select RAM in Diagnostics Menu.

2. The message of RAM test running is displayed

3. If RAM test result is okay, then you see:

4. If RAM test result is not okay, then you see:

5. Press Enter( ) button to return to the previous menu.

Diagnostics Online Diagnostics

Communication

Diagnostics Online Diagnostics

Communication

Other manuals for LK-P43

Table of contents

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide