SEA FLIPPER User manual
ELECTROMECHANICAL OPERATOR FOR SWING GATES
FLIPPER
ENGLISH
REV 02 - 03/2009
FITTING INSTRUCTIONS
and security advices
SEA S.r.l.
Zona Ind. S.Atto 64020 TERAMO Italy
Tel. +39.0861.588341 - Fax+39.0861.588344
e-mail: [email protected]
WEB SITE : www.seateam.com
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
15
FLIPPER
Flipper is an irreversible electromechanical swing gate operator for medium sized piers, maximum leaf length 2 m or 200Kg
weight(seedrawinginFig4-A)
FLIPPER
230 V (±5%) 50/60 Hz
24V
80 W
-20°C +55°C
8 Kg
200 Kg
2 m
110°
166
266
482
Fig. 1
16
1-Operator 1
2-Operator 2
3-Stop in opening (where
possible)
4-Electronic unit included
5-Flashing lamp +
antenna
6-Photocell Ghost 40
7-Differential switch 16a-
0,03a
8-Key switch Key Plus
9-Column for photocell
Pilar + Ghost40
10-Warning plate
01
1
6
5
6
3
24
7
9
9
8
3
Fig. 2
2,
2x 5
5x1
3x1
21x
2 ,x1 5 1 x RG 8+ 5
1,53x
2x1
x3 1
13 x
TECHNICAL DATA
Power Supply
Motor
Power
Working temperature
Weight
Max weight of the gate
Max. weight of the leaf
Opening degrees
DIMENSIONS (mm)
STANDARD INSTALLATION
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
REV 02 - 03/2009
FLIPPER
Fig. 3
17
1. Carter
2. Anchrage plate
3. Fuse
4. Transformator
5. Electronic control unit
6. Battery/card support (battery optional)
7. Mech./electr. Stop (electronical optional)
8. Streight articulated arm
9. Curved articulated arm
10. Back fixation
11. Portection cover
1
2
6
8
10
11
4
5
3
7
9
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
REV 02 - 03/2009
FLIPPER
CARTER OFF MOUNTING
Open the little release door and take off the screw on the inside (Fig 4).
Fig. 4
Fig. 5
Fig. 6
Limit switch
opening
Limit switch
closing
Common
Motor
Motor
Fig. 6-A
CONNECTOR
FLIPPER WITH CONTROL UNIT
FLIPPER WITHOUT CONTROL UNIT
0 Kg
120 Kg
140 Kg
160 Kg
180 Kg
200 Kg
1 mt 1,25 mt 1,5 mt 1,75 mt 2 mt
•
•
DRAWING LEAVES DIMENSIONS Fig. 4-A
USING
FIELD
Stop
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
18 REV 02 - 03/2009
GATE ARRANGEMENT
Itisnecessarytomakecontrolsonthegatetomakesuretheapplicationof FLIPPER automationcanbepossible.
Makesurethat: Fig. 7
A. Thegatefixedandmovingpartshaveastrongandcrush-
proofstructure;;
B. The weight of each leaf is not over 200 Kg (see drawing
pag.18,Fig4-A);
C. The length of each leaf is not over 2 m (see drawing pag.
18,Fig4-A);
D. The hinges are strongly anchored and are able to support
the torque of the operator; they do not have irregular
movements and/or any friction during the whole movement of
theleaf;
TheFLIPPERoperatorcomeswithlimitswitchstopinopening
and closing, nevertheless it is recommended to install
mechanical limit switch stops to be fixed on the ground in
FLIPPER
B
A
C1 /12 mm00 0
MAX 250 mm
19
Fig. 8
105°/110°105°/110°
100°/105°100°/105°
90°/100°90°/100°
300300
280280
260260
240240
220220
200200
180180
160160
140140
120120
100100 002525 5050 7575 100100 125125 150150 175175 200200 225225 250250
BB
AA
Limit Switch stop
in opening
Limit Switch stop
in closing
DIMENSIONS FOR THE INSTALLATION
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
REV 02 - 03/2009
Fig. 9
Fig. 11
Fig. 12
Fig. 10
FLIPPER
A
B
0m8 m
42 mm
MOUNTING PLATE ATTACHMENT AND MOUNTING OF THE MOTOR
- Attach the mounting plate to the pilaster with 4 screws and 4
washersnotincluded(Fig.9).
- Makesurethattheplateisinhorizontalposition(withlevel).
- Mountthemotorontheplateusingthe2furnishedscrews.
- Thetwoarticulatedarmsmustbeassembleddifferently,distinguishingtherightarmfromtheleftone.
SeeFig.11and12.
Note:Beforeinsertingthepivotslubricatethemwithwaterrepellentgrease
ASSEMBLING OF THE ARTICULATED ARM
RIGHT HAND MOUNTING
LEFT HAND MOUNTING
PIVOTS
PIVOTS
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
20 REV 02 - 03/2009
- Fitthearticulatedarmintothemotorshaftandlockitwiththespecialscrews(Fig.13).
- Theprotectioncovermustbemountedontheendofalladjustments.
FLIPPER
Fig. 13
Fig. 14
21
For further information see point “External release”.
EXTERNAL RELEASE MOUNTING
ATTACHMENT OF THE ARTICULATED ARM TO THE MOTOR
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
Return spring
REV 02 - 03/2009
Fig. 17
FLIPPER
Fig. 16
Fig. 15
FIXING OF THE FRONT BRACKET
- Close theleafcompletely
- Releasethemotor(seeFig.18e19)
- Extendthearticulatedarm(Fig.8),leantheadjustable frontbracketonthegateandmaketwomarksonthecenterofthetwo
holes(Fig.15)respectingthemeasuresinFig.8.
- Perforatetheleafandfixthefrontbracketwiththescrews(Fig.16)
- Beforetightening the screws movethefrontbrackettotherightortotheleftfor a good positioning of thearmonthegate(Fig.
17)respecting themeasureDinFig.8.
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
22 REV 02 - 03/2009
Fig. 18 Fig. 19
Toreleaseoperateasfollows:
- Takeofftheprotectioncapofthelock.
- Insertthekeyandturnabout90°intoclockwisedirection(Fig.18).
- Pullthedooruntilitscompleteopening (Fig.19).
- Openmanuallytheleaf
Toblockagainoperateasfollows:
- closethedooragain.
- Turnthekeyabout90°intoanti-clockwisedirection.
- Extractthekey.
- Closethelockagainwiththeprotectioncap.
FLIPPER
90°
23
Operator locked Operator released
RELEASE SYSTEM
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
REV 02 - 03/2009
- Releasetheoperator.
- Opentheleafcompletely oruptothedesiredopeningpoint.
- PositionthestopasinFig.24onthestopofthearmandlockthescrewsasinFig.25.
N.B:Thedeliveredscrewsareselfthreadingandhavetobelockedat10Nm.
FLIPPER
RIGHT MOTOR
LEFT MOTOR
Closing OpeningOpening Closing
STOP STOP STOP STOP
Fig. 20 Fig. 21
Fig. 25
10 mm
max
LEFTHAND MOUNTING RIGHTHAND MOUNTING
Fig. 22 Fig. 23
10 mm
max
Fig. 24
MECHANICAL POSITIVE STOP ADJUSTMENT IN OPENING
FITTING AND CONNECTION INSTRUCTIONS
ENGLISH
Sistemi Elettronici
di Apertura Porte e Cancelli
International registered trademark n. 804888
®
24 REV 02 - 03/2009
Other manuals for FLIPPER
1
Table of contents
Other SEA Gate Opener manuals
SEA
SEA Field Original instructions
SEA
SEA TORG Instruction manual
SEA
SEA TAURUS BOX 1000 User manual
SEA
SEA GATE 2 DG INVERTER User manual
SEA
SEA SURF 350 Reversible User manual
SEA
SEA Boxer 1000 User manual
SEA
SEA MINI TANK User manual
SEA
SEA LEPUS Series User manual
SEA
SEA SUPER FULL TANK 20 G6 380V User manual
SEA
SEA GER Instruction manual
SEA
SEA FLIPPER 110V User manual
SEA
SEA SURF 350 Reversible User manual
SEA
SEA HALF TANK User manual
SEA
SEA JOINT Original instructions
SEA
SEA LYRA Instruction manual
SEA
SEA SURF User manual
SEA
SEA 1110 User manual
SEA
SEA Libra Mini Tank Original instructions
SEA
SEA Cougar 270 User manual
SEA
SEA ALPHA Series Original instructions
