SEA FLIPPER 110V User manual
ELECTROMECHANICAL OPERATOR FOR SWING GATES
FLIPPER 110V
REV 00 - 03/2009
FITTING INSTRUCTIONS
and security advices
International registered trademark n. 2.777.971
SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716
Flipper is an irreversible electromechanical swing gate operator for medium sized piers, maximum leaf length 2 m or 200Kg
weight (see drawing in Fig 4-A)
FLIPPER
110V (±5%) 50/60 Hz
24V
80 W
-20°C +55°C
18 pound
441 pound
6,5 feet
110°
6,5
10
,97
Fig. 1
1-Operator 1
2-Operator 2
3-Stop in opening (where
possible)
4-Electronic unit included
5-Flashing lamp +
antenna
6-Photocell Ghost 40
7-Key switch Key Plus
8-Column for photocell
Pilar + Ghost40
9-Warning plate
9
1
6
5
6
3
2
4
8
8
7
3
Fig. 2
TECHNICAL DATA
Power Supply
Motor
Power
Working temperature
Weight
Max weight of the gate
Max. weight of the leaf
Opening degrees
DIMENSIONS (inches)
STANDARD INSTALLATION
International registered trademark n. 2.777.971
REV 00 - 03/2009 2
Fig. 3
1. Carter
2. Anchrage plate
3. Fuse
4. Transformator
5. Electronic control unit
6. Battery/card support (battery optional)
7. Mech./electr. Stop (electronical optional)
8. Streight articulated arm
9. Curved articulated arm
10. Back fixation
11. Portection cover
1
2
6
8
10
11
4
5
3
7
9
International registered trademark n. 2.777.971
REV 00 - 03/2009 3
CARTER OFF MOUNTING
Open the little release door and take off the screw on the inside (Fig 4).
Fig. 4
Fig. 5
Fig. 6
Limit switch
opening
Limit switch
closing
Common
Motor
Motor
Fig. 6-A
CONNECTOR
FLIPPER WITH CONTROL UNIT
FLIPPER WITHOUT CONTROL UNIT
0 Kg
264,5 p
309 p
353 p
397 p
441 p
3,2 f 4,1 f 4,9 f 5,7 f 6,5 f
•
•
DRAWING LEAVES DIMENSIONS Fig. 4-A
USING
FIELD
Stop
International registered trademark n. 2.777.971
REV 00 - 03/2009 4
GATE ARRANGEMENT
It is necessary to make controls on the gate to make sure the application of FLIPPER automation can be possible.
Make sure that: Fig. 7
A. The gate fixed and moving parts have a strong and crush-
proof structure;;
B. The weight of each leaf is not over 441 pound (see drawing
pag. 4, Fig 4-A);
C. The length of each leaf is not over 6,5 feet (see drawing
pag. 4, Fig 4-A);
D. The hinges are strongly anchored and are able to support
the torque of the operator; they do not have irregular
movements and/or any friction during the whole movement of
the leaf;
The FLIPPER operator comes with limit switch stop in opening
and closing, nevertheless it is recommended to install
mechanical limit switch stops to be fixed on the ground in
closing and opening (Fig. 7).
B
A
C4 i h
e/5 nc s
MAX 10 inches
Fig. 8
105°/110°105°/110°
100°/105°100°/105°
90°/100°90°/100°
1212
1111
1010
9.49.4
99
88
77
66
5.55.5
55
44
001122334455667788991010
BB
AA
Limit Switch stop
in opening
Limit Switch stop
in closing
DIMENSIONS FOR THE INSTALLATION
International registered trademark n. 2.777.971
REV 00 - 03/2009 5
Fig. 9
Fig. 11
Fig. 12
Fig. 10
A
B
0m8 m
42 mm
MOUNTING PLATE ATTACHMENT AND MOUNTING OF THE MOTOR
- Attach the mounting plate to the pilaster with 4 screws and 4
washers not included (Fig. 9).
- Make sure that the plate is in horizontal position (with level).
- Mount the motor on the plate using the 2 furnished screws.
- The two articulated arms must be assembled differently, distinguishing the right arm from the left one.
See Fig. 11 and 12.
Note: Before inserting the pivots lubricate them with water repellent grease
ASSEMBLING OF THE ARTICULATED ARM
RIGHT HAND MOUNTING
LEFT HAND MOUNTING
PIVOTS
PIVOTS
International registered trademark n. 2.777.971
REV 00 - 03/2009 6
- Fit the articulated arm into the motor shaft and lock it with the special screws (Fig. 13).
- The protection cover must be mounted on the end of all adjustments.
Fig. 13
For further information see point “External release”.
EXTERNAL RELEASE MOUNTING
ATTACHMENT OF THE ARTICULATED ARM TO THE MOTOR
International registered trademark n. 2.777.971
REV 00 - 03/2009 7
Fig.14
Return spring
Fig. 17Fig. 16
Fig. 15
FIXING OF THE FRONT BRACKET
- Close the leaf completely
- Release the motor (see Fig. 18 e 19)
- Extend the articulated arm (Fig. 8), lean the adjustable front bracket on the gate and make two marks on the center of the two
holes (Fig. 15) respecting the measures in Fig. 8.
- Perforate the leaf and fix the front bracket with the screws (Fig. 16)
- Before tightening the screws move the front bracket to the right or to the left for a good positioning of the arm on the gate (Fig.
17) respecting the measure D in Fig. 8.
International registered trademark n. 2.777.971
REV 00 - 03/2009 8
Fig. 18 Fig. 19
To release operate as follows:
- Take off the protection cap of the lock.
- Insert the key and turn about 90° into clockwise direction (Fig. 18).
- Pull the door until its complete opening (Fig. 19).
- Open manually the leaf
To block again operate as follows:
- close the door again.
- Turn the key about 90° into anti-clockwise direction.
- Extract the key.
- Close the lock again with the protection cap.
90°
Operator locked Operator released
RELEASE SYSTEM
International registered trademark n. 2.777.971
REV 00 - 03/2009 9
- Release the operator.
- Open the leaf completely or up to the desired opening point.
- Position the stop as in Fig. 24 on the stop of the arm and lock the screws as in Fig. 25.
N.B: The delivered screws are selfthreading and have to be locked at 10 Nm.
RIGHT MOTOR
LEFT MOTOR
Closing OpeningOpening Closing
STOP STOP STOP STOP
Fig. 20 Fig. 21
Fig. 25
.0,4 inc
max
LEFTHAND MOUNTING RIGHTHAND MOUNTING
Fig. 22 Fig. 23
4 c0, in .
max
Fig. 24
MECHANICAL POSITIVE STOP ADJUSTMENT IN OPENING
International registered trademark n. 2.777.971
REV 00 - 03/2009 10
Table of contents
Other SEA Gate Opener manuals
SEA
SEA JOINT Original instructions
SEA
SEA SURF 350 Reversible User manual
SEA
SEA LEPUS Series User manual
SEA
SEA ALPHA 200 PLUS User manual
SEA
SEA JOINT Original instructions
SEA
SEA MARK TANK E 270 User manual
SEA
SEA ARM Instruction manual
SEA
SEA ERG User guide
SEA
SEA Libra Mini Tank Original instructions
SEA
SEA Field Original instructions
SEA
SEA KITE User manual
SEA
SEA EASY 20 User manual
SEA
SEA SATURN User manual
SEA
SEA COMPACT 200 CP Instruction manual
SEA
SEA SURF 350 Reversible User manual
SEA
SEA SURF K 500 User manual
SEA
SEA saturn-boxer 2000 User manual
SEA
SEA MINI TANK User manual
SEA
SEA HALF TANK User manual
SEA
SEA LEPUS BOX 120V/24V User manual
