Schlage LINK FE599 User manual

FE599 Lever Lock

Installation Instructions

Alternate

Faceplate

Important Information

Lock Programming Code

six (6) digits

User Code A

four (4) digits

User Code B

four (4) digits

Web Support: part2.schlage.com

Customer Service: (877) 288-7707

1Locate Programming Code and Preset User Codes

The programming code and the preset user codes are printed on the yellow stickers located on the back of the

keypad and on the installation sheet that came in the box. Write these codes in the space provided on the ﬁrst page.

2C\,” (60 mm)

2C\v” (60 mm)

2Z\,” (53 mm)

Hole

2Check Door Dimensions

If your door does not match the dimensions shown, go to www.part2.schlage.com for instructions on how to prepare

your door.

3Install Strike Into Frame

4If Necessary, Change Latch Faceplate

Check edge of door to determine the type of faceplate required.

Door Jamb Door Jamb

5Install Latch

Latch must be ﬂipped so that bevel faces toward door jamb.

6Remove Sticker from back of Lock

8Adjust Hands-free Post

The hands-free post is the threaded stud on back of lock.

It’s purpose (in step 10) is to attach the lock and baseplate

together so that the lock will hold itself on the door.

Hands free post may need to be adjusted with a screwdriver to

the dimensions shown below.

Z\,”- Z\v”

(3 mm - 6 mm)

Hold keypad

against door

Adjust with

screwdriver so

screw extends

beyond door

edge.

7Install the Keypad

Feed the cable under latch assembly as shown below. Then slide the tailpiece through the hole as shown below.

10 Slide Baseplate onto Door over Hands-free post

Hands-free post should lock plate against door surface. If hands-free post does not lock plate onto door, see

step 8 for adjustment.

Hands-free

post

Feed Cable through Baseplate

Feed the cable through the hole as shown below. DO NOT connect the cable at this point.

12 Install Batteries and Battery Cover

11 Connect the Cable

Snap the connectors together.

13 Install Cover and Lever

See step 14 on the next page to verify that the lever is handed correctly to match your door. If the lever does not

snap into place easily, you may have to tap the lever with a hammer using a piece of wood to cushion it. Be careful

not to damage the ﬁnish of the lever.

!Tuck wires into open space on baseplate.

Be careful not to pinch any wires between

cover and baseplate.

Check Handing of Lever

Incorrect

See steps below to

change lever handing

Correct

Go to step 15

To Change Lever Handing

Test Outside Entry (When Door is Locked)

When you press your User Code (four numbers) on the keypad, the door will unlock for 5 seconds, allowing entry.

Test Locking and Unlocking from the Interior

Green light

(indicates unlocked)

Red light

(indicates locked)

To Unlock, Press Button To Lock, Press Button

Press (four numbers) Green ﬂash = unlock

!Test with door open to avoid

possibly being locked out!

Verify that latch retracts

when lever is turned

on keypad

!Test with door open to avoid

possibly being locked out!

Follow the directions on document

to continue setup.

Document 2 is located at part2.schlage.com.

17 This portion of the setup is complete.

Popular Lock manuals by other brands

Magic

Magic 105 manual

Gantner

Gantner GAT NET.Lock 7020 System Installation, configuration & operation

Wittkopp

Wittkopp Insys 7202 manual

Dorma

Dorma Studio Classic Installation instruction

Securam

Securam ECSL-601 quick start guide

Sudhaus

Sudhaus 3003 operating manual

Safety 1st

Safety 1st 48517 user guide

Pado

Pado FDS-10 user manual

Esco

Esco systeQ Series installation instructions

COMPX

COMPX National D8951 instruction sheet

secureo

secureo Key Box instruction manual

Stock Loks

Stock Loks C8713 instruction sheet

COMPX

COMPX 1T-058 Information

Auslock

Auslock T11 user manual

ELCOM

ELCOM 7205 Operating instruction

Stealth SAFES

Stealth SAFES ShadowVault Instructions & Troubleshooting

Knox

Knox KeySecure 5 Admin & user guide

Kwikset

Kwikset 48334/01 Quick installation guide