Schlage L9000 Series User manual
*P516-909*
P516-909
Indicator trim is available for either
the inside or outside of the door
on allowable functions.
Non-indicator trim is furnished on
the opposite side of the door.
Conrm desired placement
(inside or outside) before
installation.
The L9000 lock with
indicator is not intended for
exterior door applications.
For retrot, see page 9.
Check the door preparation
dimensions with the template
included in the package.
Inside cylinder with
indicator x outside cylinder
with non-indicator shown
OR
OR
Tools for installation:
Not included:Included:
Cylinder
Indicator
options:
Coin turn Thumb turnPrivacy
Non-indicator
options:
Thumb
turn CylinderCoin turn Privacy
L9000/LV9000 Series Lock with Indicator Sectional Trim Installation Instructions
1 IMPORTANT! Check lock handing before installation.
To change handing:
A. Pull out the latch
and rotate 180°.
B. Remove the lock
handing screw
from one side of
the chassis and
install it on the
opposite side.
The lock handing
screw should
always be on the
interior side of the
door.
L-Series
Actual size
AB
B\nv"
LV-Series
Actual size
A
B
2 Install lock chassis.
DO NOT FULLY
TIGHTEN CHASSIS
MOUNTING SCREWS
L9000/LV9000
Lock with Indicator
2
3 Install springs and spindles.
4 Prepare outside lever assembly for installation.
4a Install outside mounting posts.
LV functions
FULLY
TIGHTEN
MOUNTING
POSTS
ON SCREWS.
4b Install outside spring cage or spacer.
OR
LThe spring cage arrow
must point in direction
of lever down rotation.
Install spacer
for L/LV9485
5 Install outside lever.
Exterior
6 Install inside spring cage and mounting plate.
LThe spring cage arrow
must point in direction
of lever down rotation.
Interior
7 Install inside lever and rose.
8 Tighten bushing with spanner wrench.
9 Prepare the indicator side of the door.
Use template to mark and drill four (4) pilot holes.
Required for indicator side of door ONLY!
b.
Use level to align
template with door edge.
a.
Template
3
STEP 10 for OUTSIDE NON-INDICATOR ONLY.
For OUTSIDE INDICATOR, skip to STEP 11.
10 Install outside coin turn or cylinder.
Coin Turn Functions
10a Use template to mark and drill two (2) pilot holes.
10b Install the coin turn.
Exterior
b.a. Use level to
align template
with door edge.
Cylinder Functions
10a Insert key halfway into the cylinder, and install the
cylinder with ring and cylinder spring as shown.
Key inserted halfway
Exterior
10b Rotate cylinder clockwise.
For INSIDE INDICATOR trim, skip to STEP 13.
11 For Outside Indicator Trim ONLY –
Install outside indicator.
A. Trim the cam spindle if necessary (cylinder and privacy
functions).
Break the spindle at the appropriate mark according to door
thickness. (If necessary, remove clip.)
2" 1C\v" 1C\,"
B. IMPORTANT! Check indicator handing with indicator
positioned against top rim of reinforcement plate.
OUTSIDE
INDICATOR
Non-deadbolt functions* RH/RR LH/LR
Deadbolt functions and
L9040, L9044, L9056 LH/LR RH/RR
* Except L9040, L9044, L9056
If necessary to change indicator handing, refer to steps on
page 8.
4
Cylinder Functions with Indicator
11a Unlock the door.
11b Install the indicator assembly.
Exterior
DO NOT use power screwdriver.
DO NOT overtighten.
11c Install the indicator faceplate and cylinder with spring.
Key inserted
halfway
Indicator
faceplate
11d Rotate cylinder clockwise.
Privacy Functions with Indicator
11a Unlock the door.
11b Install the indicator assembly.
Exterior
DO NOT use power screwdriver.
DO NOT overtighten.
11c Install the indicator faceplate. Secure the faceplate with
two set screws.
Indicator
faceplate
Use small screwdriver.
5
Coin Turn Functions with Indicator
11a Unlock the door.
11b Install the indicator assembly.
Exterior
DO NOT use power screwdriver.
DO NOT overtighten.
11c Install the indicator faceplate. Secure the faceplate with
two set screws.
Use small screwdriver.
Indicator
faceplate
STEP 12 for NON-INDICATOR INSIDE TRIM ONLY.
For INDICATOR TRIM, skip to STEP 13.
12 Install inside cylinder or thumb turn.
Cylinder Functions
12a Insert key halfway into the cylinder, and install the
cylinder with ring and cylinder spring as shown.
Key inserted
halfway
Interior
12b Rotate cylinder clockwise.
Thumb Turn Functions
12a Use template to mark and drill two (2) pilot holes.
Use level to
align template
with door edge.
Interior
12b Install the thumb turn.
Rotate
90°
If both inside and outside of lock are now installed, skip to step 14.
6
13 For Inside Indicator Trim ONLY – Install inside indicator.
A. Trim the cam spindle if necessary (cylinder and privacy
functions).
Break the spindle at the appropriate mark according to door
thickness. (If necessary, remove clip.)
2" 1C\v" 1C\,"
B. IMPORTANT! Check indicator handing with indicator
positioned against top rim of reinforcement plate.
INSIDE
INDICATOR
Non-deadbolt functions* LH/LR RH/RR
Deadbolt functions and
L9040, L9044, L9056 RH/RR LH/LR
* Except L9040, L9044, L9056
If necessary to change indicator handing, refer to steps on
page 8.
Cylinder Functions with Indicator
13a Unlock the door.
13b Install the indicator assembly.
Interior
DO NOT use power screwdriver.
DO NOT overtighten.
13c Install the indicator faceplate and cylinder with spring.
Indicator
faceplate
Key inserted
halfway
13d Rotate cylinder clockwise.
7
Thumb Turn Functions with Indicator
13a Unlock the door.
13b Install the indicator assembly.
Interior
DO NOT use power screwdriver.
DO NOT overtighten.
13c Install the indicator faceplate. Secure the faceplate with
two set screws.
Use small screwdriver.
Indicator
faceplate
14 Tighten cylinder mounting screw, if applicable.
Cylinder
mounting
screw
15 Tighten top and bottom chassis mounting screws.
Chassis
mounting
screws
16 Install armor front.
8
INDICATOR HANDING
LH
Left Hand
LR
Left Hand
Reverse Bevel
RH
Right Hand
RR
Right Hand
Reverse Bevel
INSIDE
INSIDE
OUTSIDE
OUTSIDE
INSIDE
INSIDE
OUTSIDE
OUTSIDE
A. Determine the door's handing from outside.
B. Check indicator handing with indicator positioned against top rim of reinforcement plate.
Outside
Non-deadbolt
functions*
RH/RR LH/LR
Deadbolt functions
and L9040, L9044,
L9056
LH/LR RH/RR
*Except L9040, L9044, L9056
Inside
Non-deadbolt
functions*
LH/LR RH/RR
Deadbolt functions
and L9040, L9044,
L9056
RH/RR LH/LR
*Except L9040, L9044, L9056
To rehand the indicator:
A. Remove the E-Clip.
B. Disassemble the indicator.
Reinforcement
plate
Indicator
Cam
E-clip
Cylinder and Privacy Functions Thumb Turn and
Coin Turn Functions
Reinforcement
plate
Cam
Indicator
E-clip
C. Reorient the cam.
• Unlock the door.
• Position the indicator against the top rim of the reinforcement
plate (unlocked position).
• Position the cam as shown on charts above.
LUse OUTSIDE or INSIDE chart according to indicator side.
Reinforcement
plate
Indicator
D. Replace the E-Clip.
Cylinder or privacy function shown Coin turn or thumb turn function
shown
9
INDICATOR LOCK RETROFIT INSTRUCTIONS
1 Remove armor front.
2 Remove cylinder(s) or thumb turn if applicable.
2a Loosen the cylinder mounting screw.
2b Remove the outside cylinder, if applicable.
Insert the key halfway into the cylinder and rotate cylinder
counterclockwise to remove.
Key inserted halfway
2c Repeat for the inside cylinder, if applicable.
2d Remove inside or outside turns, if applicable.
3 Check door preparation.
IMPORTANT
• To install the indicator trim, additional door preparation may
be required.
• Please refer to the template included in this package.
• Make sure the door is prepared with any necessary holes for
the indicator trim.
4 Complete installation of indicator trim.
Go to page 2, step 9 and follow the instructions
to complete the installation of the indicator trim.
© Allegion 2018
Printed in U.S.A.
P516-909 Rev. 11/18-e
Customer Service
1-877-671-7011 www.allegion.com/us
Other manuals for L9000 Series
8
This manual suits for next models
6
Other Schlage Lock manuals
Schlage
Schlage L9010 User manual
Schlage
Schlage L9000 Series User manual
Schlage
Schlage AD-300 Quick start guide
Schlage
Schlage BE365 User manual
Schlage
Schlage B250PD User manual
Schlage
Schlage B580 User manual
Schlage
Schlage FE595 User manual
Schlage
Schlage CONNECT User manual
Schlage
Schlage CO-100-CY-70-KP-RHO-626 User manual
Schlage
Schlage BE467F User manual
Schlage
Schlage B-Series User manual
Schlage
Schlage Price Book 70A Product guide
Schlage
Schlage S-480 User manual
Schlage
Schlage M490G User manual
Schlage
Schlage B-Series User manual
Schlage
Schlage VIP 5500 Series User manual
Schlage
Schlage FE410F User manual
Schlage
Schlage Control Series User manual
Schlage
Schlage FE575 User manual
Schlage
Schlage 2 link User manual
