SAVEO SAVEO-SCAN-PKT-RCCD-BT User manual
Scanning with Simplicity
UK PH: +44 208 0998071www.saveoscan.com
US PH: +1 847 448 0412info@saveoscan.com
SAVEO-SCAN-PKT-RCCD-BT
User Guide
1. Getting Started
Introduction
Product Inforrmation
Operating Elements
LED Indicator
Connecting to iOS via Bluetooth
Connecting to Android via Bluetooth
Unpairing your device
2. User Preferences
Operating Modes
Reset to Defaults
Battery Level Status
Power Saving Mode
Sound Settings
Reading Mode
Transmission Speed
Enable the onscreen keyboard on iOS devices
Enable the onscreen keyboard on Android devices
3. Troubleshooting
4. General Information
5. Further Information
03
04
05
06
07
09
11
12
15
16
17
18
19
20
21
22
24
25
26
Contents
This document provide an easy way to program the decoding options and interface
selections by scanning barcodes listed in this guide.
Introduction
3
Important Notice
When printing barcodes for programming, the use of a high-resolution laser printer is
strongly recommended for the best scan result.
The settings will be updated periodically without prior notice. For the latest version, please
contact your authorized distributor.
Settings and Programming
Scan a series of selected barcode patches in this manual to aect setup and programming
of your handheld CCD barcode scanner. Decoding options and interface protocols can be
tailored to a specic application.
Setup parameters are stored in non-volatile memory in the scanner and are retained even
when power is o. Setup parameters change only when you reset them.
You may need to hide adjacent code patches with your hand when doing programming
scanning.
Getting started
Table of Contents
Delivery contents
1 x SAVEO-SCAN-PKT-RCCD-BT scanner
1 x Mini USB cable
1 x Quick Guide
Limited Warranty
Saveo Scan provides a one year limited warranty.
This warranty does not cover any product which has been subject to improper use,
neglect or unauthorized repair or installation.
This warranty does not cover consumable parts. (Cables & batteries are consumables.)
* Don’t put scanner in places of excessively high temperature, such as exposure to
direct sunlight
* Don’t use scanner in extremely humid conditions or in conditions of extreme
temperature change
* The rechargeable battery is permanently built into the product and cannot be
replaced.
* Never damage the rechargeable battery. Damaging the casing of the rechargeable
battery might cause explosion or re!
Product Information
4
Safety instructions
Read the operating instructions carefully and pay special attention to the safety
information. If you do not follow the safety instructions and information on proper
handling in this manual, we assume no liability for any resulting personal injury or
damage to property.
Table of Contents
Getting started
Getting Started
5
Switch on and Charge your Scanner
Please charge your scanner for 3~4 hours before rst use. Remove the protective cover
and connect the mini-USB cable to the port on the underside of the scanner and to a
mains powered USB charger.
Operating Elements
Table of Contents
Exit window
Scan/Wake
Button
Power Saving
button:
Press the button for
2~3 seconds to
enter power saving
mode
Mini USB port
with protective cover
Charge the pocket scanner with mini USB cable.
LED Indicator
(For iOS devices ONLY.
Press to raise and lower
the on-screen keyboard)
Enter pairing
mode / Unpair
from device.
LED Indicator
Please refer to the table below for information regarding LED status indicator.
Orange LED ON Full charged
Orange LED (Flashing) Charging / Low battery
Red LED ON Oine / Out of Range
Green LED ON Good read
Orange LED ON Good read (Batch mode)
LED Indicator Information
Please Note: When the battery power is too low, the Orange LED will ash and the scanner
will emit a ‘beep’ at regular intervals. The scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then power it back on.
Please Note: When the scanner is in sleep mode there will be no LED indication when
charging.
Getting Started
6
Table of Contents
Connecting to iOS via Bluetooth
Getting Started
Enable Bluetooth on your device
Go to your phone’s homescreen and nd “Settings”, then “Bluetooth” and turn
Bluetooth on.
Scan Bluetooth Prole barcodes below in order (B1 -> B2)
After you scan the Bluetooth prole barcodes, your scanner will become visible to
Bluetooth enabled devices within range.
Please note: The scanner should only be paired to one device at a time. Before you pair
your scanner to another device, please rst unpair it from the device in use. Otherwise it
will appear on your list of “Available Devices” but may not connect. In this case, please
refer to Unpairing your device in this manual.
Demo
%H%I%D
Demo
%B%R%C
continued overleaf
7
Table of Contents
B1
B2
Search for devices
Your phone will automatically search for devices, Saveo Scan will appear as an external
keyboard with a unique identier number (R-xxxxxx).
Select R-xxxxxx to connect
Select scanner from “Available
Devices” and wait for pairing process
to complete.
Devices are now paired
Once “Connected” is displayed, your
device is paired to the scanner. Your
scanner is now ready to use.
Please Note: Devices only need to be paired
once. When they are within Bluetooth range
they will automatically attempt to connect
to each other. If you wish to connect to
another device it is recommended you rst
unpair this device. Please refer to Unpairing
your device in this guide.
You are now connected. Start scanning.
Connecting to iOS via Bluetooth
Getting Started
8
Table of Contents
Enable Bluetooth on your device
Go to your phone’s homescreen and click on the menu button to nd “Settings”, then
“Bluetooth” and turn Bluetooth on.
Connecting to Android via Bluetooth
Getting Started
9
Demo
%H%I%D
Demo
%B%R%C
continued overleaf
B1
B2
Scan Bluetooth Prole barcodes below in order (B1 -> B2)
After you scan the Bluetooth prole barcodes, your scanner will become visible to
Bluetooth enabled devices within range.
Please note: The scanner should only be paired to one device at a time. Before you pair
your scanner to another device, please rst unpair it from the device in use. Otherwise it
will appear on your list of “Available Devices” but may not connect. In this case, please
refer to Unpairing your device in this manual.
Table of Contents
Search for devices
Click “Search for Devices” at the bottom of the screen and Saveo Scan will appear as an
external keyboard with a unique identier number (R-xxxxxx).
Select R-xxxxxx to connect
Select scanner from “Available
Devices” and wait for pairing process
to complete.
Connecting to Android via Bluetooth
Getting Started
Devices are now paired
Once “Connected” is displayed, your
device is paired to the scanner. Your
scanner is now ready to use.
Please Note: Devices only need to be paired
once. When they are within Bluetooth range
they will automatically attempt to connect
to each other. If you wish to connect to
another device it is recommended you rst
unpair this device. Please refer to Unpairing
your device in this guide.
You are now connected. Start scanning.
10
Table of Contents
Other manuals for SAVEO-SCAN-PKT-RCCD-BT
2
Table of contents
Other SAVEO Scanner manuals
