Savant SmartControl SSC-W003I User manual

SSC-W003I Quick Reference Guide | 009-1504-01 45 Perseverance Way, Hyannis, MA 02601

Box Contents

(1) SmartControl 3 Controller (SSC-W003I)

(1) Installation Kit (075-0174-xx)

(1) Mounting Plate (074-0569-xx)

(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)

(1) 5V DC 1.2A Power Supply (025-0207-xx)

(1) Cable Tie (014-0071-xx)

(1) Product Regulatory Document (009-1950-xx)

Speciﬁcations

Environmental

Temperature 32° to 104° F (0° to 40°C)

Humidity 10% to 90% (non-condensing)

Dimensions and Weights

Height Width Depth Weight

Device 0.64 in

(1.62 cm)

2.70 in

(6.85 cm)

2.67 in

(6.78 cm)

0.50 lbs

(0.22 kg)

Shipping 3 in

(7.62 cm)

7 in

(17.78 cm)

10 in

(25.40 cm)

2.0 lbs

(0.90 kg)

Power

Input 5V DC 1.2A

Maximum 6 watts

Standards

Wireless

Wi-Fi (802.11 b/g/n 2.4 GHz)

IMPORTANT! 802.11r (fast roaming) is not

supported.

Security WPA™, WPA2™, WPA/WPA2™, WEP

Savant® SmartControl 3 Wi-Fi Controller (SSC-W003I)

Quick Reference Guide

Network Guidelines

For more information, see the Savant Device Networking Guidelines

on the Savant Customer Community.

Front Panel

Press and hold for ﬁve seconds while powered On to clear the

network settings. The Status LED blinks rapidly when reset is

complete.

O: No Power

On Solid: Provisioned to the local network and communicating

with the Savant System Host.

Blinks Once: In Provisioning Mode. Ready to be added to the

local network.

1s.5s

REPEAT

Blinks Twice: Establishing connection with the local network.

.5s.5s .5s

REPEAT

Blinks Three Times: Connected to the local network. Is

connecting to the Host.

.5s .5s.5s .5s

REPEAT

.5s 1s

Short O Blink: Firmware is updating.

.5s1.5s

REPEAT

Rapid Blink: The reset button was held down for at least ﬁve

seconds and the SSC-W003I is performing a factory reset. After

reset, all network settings are cleared and the factory defaults

are set.

.1s.1s .1s

REPEAT

.1s

Reset

Status

Regulatory

Safety and

Emissions

FCC Part 15 CE C-Tick UKCA

Contains FCC ID: TLZ-CU277

Contains IC: 6100A-CU277

RoHS Compliant

Minimum Supported Releases

Savant OS da Vinci 8.4

SSC-W003I Quick Reference Guide | 009-1504-01 45 Perseverance Way, Hyannis, MA 02601

Rear Panel

5 VDC

-IR

1 2 3-

Used to send IR signals to control devices with

an IR input or IR receiver via an IR ﬂasher (5V

tolerant only).

Before making connections, see the IR Wiring

section for important precautions regarding IR

functionality.

Input Power 5V DC 1.2A - Connect to included power supply.

Cable Lance Use with included cable tie to secure power

supply connection.

IR Wiring

IR connections are made using the 6-pin screw down plug-in type

connector included with each SSC-W003I controller. This connector

plugs into the connection on the rear of the controller.

IMPORTANT! IR Wiring Precuations

–Ensure all IR emitters are within 15 feet (4.6 meters) from the

controller’s location.

–Use of 3rd party ﬂashing IR emitters with Talk Back is not

recommended. These types of emitters can draw voltage away

from the IR signal that can degrade IR performance.

Making Connections

1. Remove Power if power is applied.

2. Pull to remove the terminal block from the rear of the controller.

3. With a small ﬂat bladed screwdriver,

turn the screws on the top of

connector counterclockwise until

the silver crimps in the front of the

connector opens enough to slide the

wire(s) into the square slots.

4. Strip back the insulation on each of

the wires ¼ inch. Insert the stripped

wires into their proper ports. Do not

allow more than ⅛ inch of bare wire

exposed.

5. Turn the screws clockwise until the screw tightens around the wire.

Tug on the wire a bit to verify the wires are installed securely.

6. Continue until all wires are installed.

7. Repeat steps 3 - 5 for any additional IR devices.

8. Plug terminal block back into the rear of the controller.

9. Reapply power.

Connecting to a Wireless Network

To provision the SSC-W003I controller onto a local network, one of the

following methods can be used:

–SmartConnect Application – da Vinci 8.4 or later.

–Embedded Web UI – All da Vinci builds.

Both methods are described in the SmartControl 3 – (SSC-W003I)

Deployment Guide.

Additional Documentation

Additional Documentation is available on the Savant Customer

Community.

–SmartControl 3 (SSC-W003I) Deployment Guide (009-0274-xx)

–SmartConnect Software Reference Guide (009-1046-xx)

–SmartControl 3 SSC-W003I Troubleshooting Guide.

4 5 632

PIN 1 IR 1-

PIN 2 IR 1+

PIN 3 IR 2-

PIN 4 IR 2+

PIN 5 IR 3-

Use White Stripe

for Positive (+)

6 IR 3+

1 2 3

< 1/8 inch

bare wire

exposed

Other Savant Controllers manuals

Savant

Savant FRC-P100-00 User manual

Savant

Savant Lamp Controller User manual

Savant

Savant SmartLighting SSL-P018 User manual

Savant

Savant SSC-0008 User manual

Savant

Savant Super Pro Host v2 SVR-7100S Quick reference guide

Savant

Savant SmartControl 12 User manual

Savant

Savant SmartControl 12 User manual

Savant

Savant WIF 104 Series User manual

Savant

Savant Pro Host User manual

Savant

Savant SmartControl 25 User manual

Savant

Savant SmartControl SSC-W002G User manual

Savant

Savant HST-4001 User manual

Savant

Savant SmartLighting 18 User manual

Savant

Savant Touch 5.5 Quick reference guide

Savant

Savant SmartControl 3 User manual

Savant

Savant S2 User manual

Savant

Savant Director Lite HST-DIRECTORLITE User manual

Savant

Savant SmartControl 3 User manual

Savant

Savant LCB-DMX1 Quick reference guide

Savant

Savant S2 Quick reference guide

Savant

Savant CPT-1212 User manual

Savant

Savant SSC-002485 Operating instructions

Savant

Savant CPT-1212 User manual

Savant

Savant SmartMedia 6 User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual