Savant SmartControl 3 User manual

SSC-W103I Quick Reference Guide | 009-1580-02 45 Perseverance Way, Hyannis, MA 02601

Box Contents

(1) SmartControl 3 Controller (SSC-W103I)

(1) Installation Kit (075-0174-xx)

(1) Mounting Plate (074-0569-xx)

(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)

(1) 5V DC 1.2A Power Supply (025-0207-xx)

(1) Cable Tie (014-0071-xx)

(1) Product and Regulatory Insert (009-1950-xx)

Environmental

Temperature 32° to 104° F (0° to 40° C)

Humidity 10% to 90% Relative Humidity (non-condensing)

Dimensions and Weight

Height Width Depth Weight

Device 0.64 in

(1.62 cm)

2.7 in

(6.85 cm)

2.67 in

(6.78 cm)

0.50 lbs

(0.22 kg)

Shipping 3.00 in

(7.62 cm)

7.00 in

(17.78 cm)

10.00 in

(25.40 cm)

2.00 lbs

(0.90 kg)

Power

Input Power 5V DC 1.2A

Max Power 6 watts

Standards

Wireless

Wi-Fi (802.11 b/g/n 2.4 GHz)

IMPORTANT! 802.11r (fast roaming) is not

supported.

Security WPA™, WPA2™, WPA/WPA2™, WEP

Regulatory

Safety and

Emissions

FCC Part 15 CE C-Tick UKCA

Contains FCC ID: TLZ-CU277

Contains ID: 6100A-CU277

RoHS Compliant

Minimum Supported Release

Savant OS da Vinci 8.8

Speciﬁcations

Front Panel

Network Guidelines

For more information, see the Savant Device Networking Guidelines

on the Savant Customer Community.

Reset Status

Press and hold for ﬁve seconds while powered On to clear the

network settings. The Status LED blinks rapidly when reset is

complete.

O: No Power

On Solid Green: Provisioned to the local network and

communicating with the Savant Pro System Host.

Blink Green Once: In Provisioning Mode. Ready to be added to

the local network.

Blink Green Twice: Establishing connection with the local

network.

Blink Green Three Times: Connected to the local network. Is

connecting to the Host.

Short O Green Blink: Firmware is updating.

Rapid Green Blink: The reset button was held down for at least

ﬁve seconds and the SSC-W103I is performing a factory reset.

After reset, all network settings are cleared and the factory

defaults are set.

Red: RF scan mode. This is used to bind a Savant Button

Remote.

1s.5s

REPEAT

.5s.5s .5s

REPEAT

.5s .5s.5s .5s

REPEAT

.5s 1s

.5s1.5s

REPEAT

.1s.1s .1s

REPEAT

.1s

Savant® SmartControl 3 - Wi-Fi Smart Controller with 3 IR and RF (SSC-W103I)

Quick Reference Guide

SSC-W103I Quick Reference Guide | 009-1580-02 45 Perseverance Way, Hyannis, MA 02601

IR Wiring

IR connections are made using the 6-pin screw down plug-in type

connector included with each SSC-W103I controller. This connector

plugs into the connection on the rear of the controller.

IMPORTANT! IR Wiring Precautions

– Ensure all IR emitters are within 15 feet (4.6 meters) from the

controller’s location.

– Use of 3rd party ﬂashing IR emitters with Talk Back is not

recommended. These types of emitters can draw voltage away from

the IR signal that can degrade IR performance.

Use white stripe

for positive (+)

PIN 1 IR 1

PIN 2 IR 1 +

PIN 3 IR 2

PIN 4 IR 2 +

1 +

2 +

3 +

432

165

PIN 5 IR 3

PIN 6 IR 3 +

Making Connections

1. Remove Power if power is applied.

2. Pull to remove the terminal block from the rear of the controller.

3. With a small ﬂat bladed screwdriver,

turn the screws on the top of the

connector counterclockwise until

the silver crimps in the front of the

connector opens enough to slide the

wire(s) into the square slots.

4. Strip back the insulation on each of

the wires ¼ inch. Insert the stripped

wires into their proper ports. Do not

allow more than ⅛ inch of bare wire

exposed.

5. Turn the screws clockwise until the screw tightens around the wire.

Tug on the wire a bit to verify the wires are installed securely.

6. Continue until all wires are installed.

7. Repeat steps 3 - 5 for any additional IR devices.

8. Plug terminal block back into the rear of the controller.

9. Reapply power.

Connecting to a Wireless Network

To provision the SSC-W103I controller onto a local network, one of the

following methods can be used:

– SmartConnect Application – version 1.7 or later.

– Embedded Web UI – All da Vinci builds.

Both methods are described in the Deployment Guide: SmartControl 3.

Additional Documentation

Additional Documentation is available on the Savant Customer

Community.

– Deployment Guide: SmartControl 3 (009-1274-xx)

– SmartConnect Software Reference Guide (009-1046-xx)

Rear Panel

5 VDC

-IR

- 1 + - 2 + - 3 +

A B C

Used to send IR signals to control devices with

an IR input or IR receiver via an IR ﬂasher (5V

tolerant only).

Before making connections, see the IR Wiring

section for important precautions regarding IR

functionality.

Input Power 5V DC 1.2A - Connect to included power supply.

Cable Lance Use with included cable tie to secure the power

supply connection.

< 1/8 inch

bare wire

exposed

Other manuals for SmartControl 3

This manual suits for next models

Other Savant Controllers manuals

Savant

Savant S2 Quick reference guide

Savant

Savant SmartControl User manual

Savant

Savant WIF 104 Series User manual

Savant

Savant SmartControl 25 User manual

Savant

Savant Lamp Controller User manual

Savant

Savant SmartMedia 6 User manual

Savant

Savant SmartControl 3 User manual

Savant

Savant LCB-DMX1 Quick reference guide

Savant

Savant CPT-1212 User manual

Savant

Savant SmartControl 3 User manual

Savant

Savant SmartControl 3 Quick reference guide

Savant

Savant SmartLighting 2 User manual

Savant

Savant Director Lite HST-DIRECTORLITE User manual

Savant

Savant SmartControl 3 User manual

Savant

Savant SmartMediaPro 6 Quick reference guide

Savant

Savant S2 User manual

Savant

Savant SmartLighting 2 User manual

Savant

Savant SmartControl 7 User manual

Savant

Savant SmartControl 25 User manual

Savant

Savant SmartLighting 18 User manual

Savant

Savant S2 User manual

Savant

Savant SmartControl 2 Quick reference guide

Savant

Savant SmartControl 2 User manual

Savant

Savant QO PBC-1000-10 Quick reference guide

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual