Sangean PR-D4 User manual

中文

Rersion 2

PR-D4

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades

and a third grounding prong. The wide blade or the third prong

are provided for your safety. If the provided plug does not fit

into your outlet. consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified

by the manufacturer, or sold with the apparatus. When a cart is

used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged. liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. To Reduce the Risk of Fire or Electric Shock, Do not Expose

This Appliance To Rain or Moisture.

16. The Shock Hazard Marking and Associated Graphical Symbol is

provided on the bottom panel of unit.

17. Apparatus shall not be exposed to dripping or splashing and no

objects filled with liquids, shall not be placed on the apparatus.

Controls

Tuning Up/Down

Scan tuning and Time setting

Preset buttons

Volume Control

LCD display

Buzzer alarm set

Radio alarm set

Band and Tuning step selection

Power button

Headphone socket

DC input socket

Telescopic aerial

Battery compartment

LCD Display

Sleep and snooze status

Frequency

Band indicator

Preset stations

Battery power

Frequency unit

Radio alarm

Buzzer alarm

Clock

Time set

PM for clock

Battery operation

1. Remove the battery cover on the rear of the unit by pressing

the catch.

2. Insert four UM-1 (D size) batteries into the spaces in

the compartment.

3. Take care to ensure all batteries are inserted with correct polarity

as shown on the rear cabinet. Replace the battery cover.

4. Reduced power, distortion and a “stuttering sound” or low battery

sign is flashing with an “E“ shown on the display are all signs that

the batteries need replacing.

5. If the radio is not to be used for any extended period of time,

it is recommended that the batteries are removed from the radio.

Using AC power adaptor

(not supplied in some markets)

The AC power adaptor required for this unit should be 6 volts DC

at 400 mA center pin negative.

Insert the adaptor plug into the DC socket on the left side of

the radio. Plug the adaptor into a standard mains socket outlet.

Whenever the adaptor is used, the batteries are automatically

disconnected. The AC adaptor should be disconnected from the

main supply when not in use.

Setting the clock

1. Clock can be set either the radio is power on or off.

2. Display will show “ - : - - “ when the batteries are installed or when

the radio is connected to the mains supply.

3. Press the button for more than 2 seconds, display will flash time

set symbol and also the hour digits, followed by a beep.

4. Press Tuning Up/Down buttons to set the required hours.

5. Press button, the minute digits will flash.

6. Press Tuning Up/Down buttons to set required minute.

7. Press the button to complete time setting.

Operating the radio

This radio is equipped with three tuning methods – Scan tuning,

Manual tuning and Memory presets recall.

Scan tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band button.

For FM band fully extend and rotate telescopic aerial to get

best reception. For MW (AM) band, rotate the radio to get

best signal.

3. Press and release Scan button (long press Scan button more than

2 seconds will activate time setting), the radio will up search and

stop automatically when it finds a radio station.

Press the Scan button again to pick up the found station .

Note:

The radio will continue to search next available stations if you

do not press Scan again when it finds a radio station.

4. Rotate the Volume control to get required sound level.

5. To turn off the radio, press the Power button.

Display will show OFF.

Manual tuning/station searching

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band button.

Adjust the antenna as described above .

3. A single press on either the Tuning up or down button will change

the frequency in the following increments:

FM: 50 or 100 kHz

MW: 9 or 10 kHz

4. Press and hold either Tuning Up or Down button until the frequency

in the display begins to change rapidly. Release the button.

Your radio will search the selected waveband and stop

automatically when it finds a station of sufficient strength.

5. Rotate the Volume control to get required sound level.

6. To turn off the radio, press the Power button.

Display will show OFF.

Storing stations in preset memories

There are 5 memory presets for each waveband.

1. Press the Power button to turn on the radio.

2. Tune to required station using one of the methods

previously described.

3. Press and hold down the required preset until the radio beeps.

The preset number will appear in the display and the station will

be stored under chosen preset button.

4. Repeat this procedure for the remaining presets.

5. Stations stored in preset memories can be overwritten by

following above procedures.

Recalling stations from preset memories

1. Press the Power button to turn on the radio.

2. Select the required waveband.

3. Momentarily press the required Preset button, the preset number

and station frequency will appear in the display.

Setting the radio alarm

When the radio alarm is selected, the radio will turn on and play the

chosen radio station at the chosen alarm time. The radio alarm will

continue for one hour unless turned off by pressing the Power button.

Press the Power button whilst the alarm is activated will cancel the

alarm for 24 hours.

Note:

Radio alarm can be activated only until both radio alarm time and

radio alarmed station are set. Radio alarm will be automatically

switched buzzer alarm when the radio is in low battery status or the

selected radio alarm station signal is too weak.

a. Setting the radio alarm

1. The radio alarm can be set when radio is on or off.

2. Press and hold the radio alarm button until the radio alarm symbol

flashes on the display followed by a beep.

3. Press the Tuning up/ down button to select the desired hour and

press the Time setting button to confirm hour setting.

4. Press the Tuning up/ down button to select the desired minute and

press the Time setting button to confirm minute setting.

5. While radio alarm symbol is flashing, press the Tuning up/ down to

select desired wake-up band and station, then press the Time

setting button to confirm the selection. Radio alarm setting is

now completed.

b. When the alarm sounds

6.To cancel a sounding alarm, press the Standby button to cancel a

sounding alarm.

c. Disabling / cancelling alarm setting

7.To cancel the radio alarm setting, press and hold the radio alarm

button for 2 seconds (followed by a beep) before the alarm

sounds off.

Note:

If new radio alarm station is not selected, it will select the last alarm

station.

Setting the HWS (Humane Wake System)

buzzer alarm

A beep tone will activate when selecting the HWS alarm.

The alarm beep will increase in volume every 15 seconds for one

minute followed by one minute silence before repeating the cycle.

The HWS alarm will sound for one hour until turning off by pressing

the Power button. Press the Power button whilst the alarm is

activated will cancel the alarm for 24 hours.

a. Setting the buzzer alarm

1. The buzzer alarm can be set when radio is on or off.

2. Press and hold the buzzer alarm button until the buzzer alarm

symbol flashes on the display followed by a beep.

3. Press the Tuning up/ down button to select the desired hour and

press the Time setting button to confirm hour setting.

4. Press the Tuning up/ down button to select the desired minute and

press the Time setting button to confirm minute setting.

Buzzer alarm setting is now completed.

Other manuals for PR-D4

Table of contents

Other Sangean Receiver manuals

Popular Receiver manuals by other brands

Garmin

Garmin GA 23 Owner's manual and reference guide

Aiphone

Aiphone PS-12F instructions

IMES

IMES TCS-01CA-PMI Original Operating Instruction

BWI Eagle

BWI Eagle AIR-EAGLE SR Product information bulletin

AMIMON

AMIMON AMN12310 WHDI datasheet

Dual

Dual DMCPA79BT Installation & owner's manual

Sound Associates

Sound Associates SA652P Operation manual

Sherwood

Sherwood NewCastle R-772 Service manual

Audio

Audio A10-RX Series user guide

AllSee

AllSee PushShare PSRV1.1 user manual

DEMAG

DEMAG DRC-DR D2 operating instructions

Teleco

Teleco TVRCL868A02 manual

Bosch

Bosch RF3222E installation instructions

Kramer

Kramer 631R user manual

Xpress

Xpress xmc10 installation guide

JVC

JVC KD-MR1BTS instruction manual

Omega Engineering

Omega Engineering UWTC-REC3 user guide

e-survey

e-survey E300 Pro user manual