Safeguard Supply ERA-PBDCR User manual
air ranitter to eceier
(Always test unit prior to installation)
The transmitter wors with the EAD receiver & basic programming
calls for the user to pair the transmitters with a receiver & select a melody for
the transmitter to instruct the receiver to play when triggered.
For quick setup, however, each zone defaults to a basic "ding-dong" sound allowing you to
easily pair the transmitter for a faster set up process.
Figure 1
Battery Intaation
hanin the one eody
By default, each zone is programmed by the factory to play the ding-dong
sound
1. Hold down the "zone" button until you hear a short tone & all LEDs on
front panel of receiver are red (approx 3 seconds). The zone you are
programming will flash.
2. ress the "volume" button to scroll through the 12 available melodies
for selection. nce you find a melody you lie, move to step 3.
3. ress the "zone" button to scroll to the next zone & repeat step 2 to
program a melody to other zones.
4. nce you have programmed a melody to all necessary zones, move to
step 5.
5. Hold down the "zone" button until you hear a short tone sound (approx
3 seconds) notifying the receiver is out of melody programming mode.
Owner’s Manual
This device complies with Part 15 of the FCC rules, Operation of this device is subject
to the following conditions: 1. This device may not cause harmful interference. 2. This
device must accept any interference, including interference that may cause unde-
sired operation.
e ote
•Each receiver is capable of pairing with four (4) transmitters per zone.
•Each zone features 1 x 12 D output.
•utput duration for the 12 D output may be set to 5 sec, 1 sec, 1
min, & 2 min. The receiver features 1 x Form relay assignable to one
or multiple zones & will tae on the duration of the 12 D output.
•olume control 4 levels plus mute, plus off.
•Each transmitter must be paired to a zone on the receiver.
•Each zone is programmed to the "dingdong" sound from the factory.
ser may change this melody.
•hen transmitter battery is low, it sends a signal to the receiver when
triggered & the corresponding LED on the receiver will continue to
flash for 1 minutes.
•The EAT is a push button transmitter that must be
programmed to a EA compatible receiver to operated.
•ush button measures 3. H x 2.25 x 1.5 D.
•The halo ring around the center push will illuminate dimly for
visibility at night (this feature consumes very little power.)
•hen triggered (center push button is pressed) the center halo
illuminates brightly for approximately 2 seconds.
•The push button is outdoor rated and contains a silicone gaset to
eep moisture out. ount with the small weep hole pointing down
to ensure any moisture in the unit evaporates out.
Figure 2
1. n the EAD receiver, hold down the "mode" (left button in figure 3
below) button until you hear a short tone sound & the "zone 1" LED flashes
(approx 3 sec).
2. f you are programming the transmitter to zone 1 press the button on your
transmitter. ou will hear the receiver play a short musical note (zone 1 will
continue to flash).
3. To program a transmitter to a different zone, press the "zone" button on
the receiver to scroll to the appropriate zone . The zone you want to
program will flash. epeat step 2 above.
4. nce you have programmed all the zones move to the next step.
5. To exit program mode, hold down the "mode" button until you hear a short
tone sound (approx 3 sec)
1. pen the front cover by inserting the included screwdriver into the
suare hole on the bottom of the unit (figure 1) & gently push & then
separate the top & bottom halves of the case.
2. emove top part of case from lower part of case (figure 2).
3. nstall the included 245A battery into the holder with positive () side
of the battery facing up (figure 2).
4. Test the battery by pressing the center push. The green halo should
illuminate for approximately 2 seconds, signaling transmission. ote
rogram the push button to a compatible receiver to mounting the push
button.
oe te
The volume button on the side of the receiver controls the four different volume
levels, mutes & turns off the receiver. Pushing the volume button controls these
functions.
•hen all four zone LED lights are red, this indicates maximum volume.
•Three zone LED lights indicate the third volume level.
•Two zone LED lights indicate the second volume level.
•ne zone LED light indicates the minimum volume level.
•o zone LED lights & a red power indicator light means the
Figure 3
TECHNICAL SUPPORT
If you encounter any difficulty in the operation of this product after reading
the manual, please contact us. You can reach us by phone at 4245114
from 8:0 AM to 5:00 PM Monday through Friday (Eastern Standard Time). We
will be happy to answer your questions and help you in any way we can.
WARRANTY
Safeguard Supply warrants this product to be free of defects in material and
workmanship for a period of one year from the date of purchase. This
warranty does not cover damage resulting from accident, abuse, act of God
or improper operation. If this product does become defective, simply return
it to Safeguard Supply. Please include a note describing the troubles along
with your name and return address as well as the original sales receipt. If the
product is covered under warranty it will be repaired or replaced at no
charge. If it is not covered by warranty, you will be notified of any charges
before work is done.
Safeguard Supply
22 oon Station t. 11
Kennesaw, A 3144
www.safeguardsupply.com
1. Hold down "mode" button until you hear a short tone & the zone 1
LED flashes.
2. Hold down the "mode" & "volume" button simultaneously until all
LEDs stop flashing & you hear a short melody sound
(approximately 5 seconds).
3. All LEDs will stop flashing & only the green LED power indicator will
display. The memory is now erased.
rain rorain eory
in tt
•Each zone on the EAD features a live 12 D output.
•The output duration may be set to 5 seconds, 1 seconds, 1 minute or 2
minutes using the dip switches located inside the receiver.
•The output duration settings will apply to all zones & the Form elay.
•The Form elay may be associated with a specific zone or multiple zones.
•12 D output current 4mA maximum.
nplug the receiver.
Separate top receiver case from bottom receiver case.
Locate terminal bloc (see figure 4) located on the bottom of the pc board.
Loosen screws for the zone(s) that you are connecting a device to.
ire the external 12 D into the terminal connection blocs that
corresponds to the respective zone. For example, if a push button is
paired to zone 1, and you want a strobe to flash for zone 1, wire the
strobe into the terminal block for zone 1.
bserve polarity when necessary. For example, for a strobe light,
ensure you are connecting the positive wire on the strobe to the positive
terminal on the receiver.
etighten screws on terminal bloc.
Adjust output duration as needed (figure 5)
Snap cover bac together.
lug in receiver.
onnectin a eice
(Figure 4)
(Figure 5)
ontin the h Btton
Ensure you have programmed & tested the push button prior to mounting.
There are two mounting options for the EAT. The first method is to
mount the unit using the supplied screws. The second is using the
supplied doublesided tape.
1. pen the front cover by inserting the included screwdriver into the
suare hole on the bottom of the unit (figure 1 above) & gently push in
to separate the top & bottom half of the case.
2. emove top half of case from lower half of case.
3. lace bac cover of push button on wall where you want to mount it.
The bac cover may be mounted using the supplied screws or double
sided mountin gtape.
4. Ensure the arrow inside the bac cover is pointing up.
5. ount bac half of case on wall.
. lace top half (with battery installed) over bottom half. ae sure the
small opening (see figure 1 above)on top half is pointing down. lace
bottom of the top half over the small protruding clip on bottom half &
snap into place.
Low Battery Indicator
hen the battery in the EAT is low & needs to be replaced, it will
signal the receiver to double play the programmed melody on the
receiver when triggered.
For example, if you have programmed the "dingdong" sound for the
push button to play on the receiver, when the battery on the push
button is low, the receiver will play "dingdong...dingdong" when
triggered, notifying you to change the battery in the push button.
Other Safeguard Supply Receiver manuals
