Rosslare AY-L23 User manual
Rosslare
Installation Instructions
Model: AY-L23
10/01
The table below shows how you should wire the receiver to the
Controller.
Cable Notes:
1. The individual wires coming out of the receiver are color coded
according to the recommended Wiegand standard.
2. When using a separate power supply for the receiver, this supply and the
Controller's power supply must have a common ground.
3. The cable shield wire on the receiver should be attached to an Earth
ground (best) or signal ground connection at the panel or power supply
end of the cable. This configuration is best for shielding the receiver
cable from external interference.
The receiver should be tested after wiring it to a power supply and
the Controller. Do this by performing the following steps:
1. Power up the receiver.
2. Transmit using a Rosslare wireless remote control to the receiver.
The LED will momentarily flash green and a short beep will be
emitted. This indicates that the transmission has been received
properly by the receiver.
3. After the data is processed by the Controller, the Controller can
then turn the LED green. Refer to the Controller description of
the LED operation if the receiver LED is controlled by the
Controller.
OPERATION INSTRUCTION
COLOR
Red
Black
White
Green
Brown
Purple
WIEGAND
OUTPUT
DC+Input
Ground
Data 1
Data 0
LED Control
Tamper
-1- -3-
SPECIFICATIONS
Power Supply Type
Operating Voltage Range
Linear type recommended
5 - 16 VDC
Maximum Input Current
Tamper Output
Maximum Cable Distance
to Controller
Frequency:
Open collector, active low,
max. sink current is 16 mA
150 meters (500 ft.)
433 Mhz
Read Range:
Operating Temp. Range:
Operating Humidity:
Dimensions:
-31 C to 63 C (-25 F to 145 F)
ooo o
0 to 95% (non condensing)
Standby : 25 mA
Receive : 55 mA
The AY-L23 is a weather resistant wireless receiver,
compatible with all of Rosslare’s wireless remote
control transmitters. When receiving an ID from a
wireless transmitter, the AY-L23 will output the ID
in 26-Bit Wiegand format to an attached 26-Bit
Wiegand controller.
See Page 2 for a list of compatible transmitters. Output Modulation:
The is to be used with control panels whose power supply
is UL Listed Class 2 or equivalent.
receiver
26-Bit Wiegand
5.7” (145mm) L x 1.7” (43mm) W x 0.8” (20mm) D
-2- -3-
Suitable for outdoor use
165ft (50m)
MOUNTING INSTRUCTION
To mount the receiver, perform the following:
receiver
receiver
receiver.
receiver
receiver
1. Determine an appropriate mounting position for the . Do
not mount the receiver near any source of wireless interference or
on any metal surface.
2. Peel off the back of the self-stick mounting label template
included with the unit and place at the desired mounting position.
3. Using the template as a guide, drill two holes (hole size is
indicated on mounting template) for mounting the to the
surface.
4. Drill a 7/16" (10mm) hole for the cable.
5. Remove the front case from the
6. Attach the to the controller. (See wiring instructions)
7. Screw the s rear case on to its mounting location see and
return the front case onto the mounted rear case.
WIRING INSTRUCTION
The is supplied with an 18-inch pigtail, having a 6-wire
cable. To connect the to the Controller, perform the
following steps:
1. Prepare the cable by cutting the cable jacket back 1
inches and strip the wires inch.
2. Prepare the Controller cable by cutting the cable jacket back 1
inches and strip the wires inch.
3. Splice the pigtail wires to the corresponding Controller
wires and cover each connection (see the table on Page 2).
4. If the tamper output is being utilized, connect the purple wire to
the correct input on the Controller.
5. Trim and cover all conductors that are not used.
receiver
receiver
receiver
receiver’s
1/4
½
1/4
½
SA-03C Three Button Remote Control
SA-26C One Button Remote Control
SA-27C Two Button Remote Control
SA-28C Four Button Remote Control
COMPATIBLE TRANSMITTERS
All manuals and user guides at all-guides.com
all-guides.com
2200.8071 RF læser 26bit
Original ledning
Brun=LEDG
Lilla=Sabotage
Hvid=D1
Grøn=D0
Rød=+12V
Sort=GND
TA
GND
D-
D+
12Vin
GND
LedG
Buz
D1/DT
Rx
D0/CK
Dallas
+12V
GND
LedR
Lukket = adr.1
Åben = adr.0
Sabotage
indgang
4 3 2 1
All manuals and user guides at all-guides.com
Other Rosslare Receiver manuals
