Roland CammJet CJ-500 User manual
Refer to yourCAMMJET / Hi-Fi JET user’s manual for detailed instructions on working with the unit.
1
Quick Start Guide
Unpacking
Begin by unpacking the stand. Instructions are included in the box. Then prepare the main unit and install
on stand. Make sure that the unit is firmly attached to the stand before proceeding. Ink waste tank
assembly is recommended next.
Powering on
The main display will prompt you to select an ink type and press ENTER.
Turn ON the main power first
Then turn ON secondary power.
Roland CJ-500 Or Roland Hi-Fi JET
Ver.1.00
Roland CJ-500
UNKNOWN INK TYPE
SELECT INK TYPE
PIG.CMYKLcLm
INSTALL
DRAIN TANK
NOW FILLING INK
Use the [ ] [ ] key to select the installed ink type
and press the [ENTER] key.
No ink is filled.
Attach the drain tank, and
press the [ENTER] key.
The system will execute ink fill.
This operation takes several minutes.
PIG. CMYKLcLm/PIG. CMYKOrGr/DYE CMYKLcLm
Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.
2
Pass the material between the pinch rollers and the grit
rollers as shown in the figure.
1
Move the sheet loading lever toward LOAD.
The pinch rollers lower to hold the material in place.
3Close the front cover.
Use the [ ] and [ ] keys to select [Piece], then
press the [ENTER] key.
4
Sheet loading lever
Loading Flat Material
Refer to steps 5 and 6 in "Loading Roll Material," and
position the material and the pinch rollers correctly.
2
Press the [SETUP] key. This detects the width and
length of the material and shows the printable width
and length on the display.
5Note for CAMMJET: If a pinch roller is positioned over an
area where there is no grit roller, the message shown at below
appears when you press the [SETUP] key.
PINCHROLL ERROR
INVALID LEFTPOS
or [RIGHT]
Top menu
W1000mm L1230mm
FINE BI-DIR
*If the material is misaligned and looks like it might
come loose from the pinch rollers, or actually does
come loose, please reload the material.
Setup for Printing
Check the positioning of the pinch rollers and
make sure they are aligned at the correct positions.
The SETUP LED lights up
SETUP SHEET
ROLL EDGE PIECE
Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.
3
Head test print
Before starting to print, perform the Head Test Print to check the state of the head.
Missing dots may reduce the printing quality. On the CAMMJET simply press [Print Test]. On the FJ:
If there are any missing dots or other evidence of a drop in printing quality, clean the head (see
User’s Manual section concerning "Cleaning the Printing Heads").
Head Height Adjustment
The CAMMJET have 3 settings for head height: 1.1mm, 1.6mm & 2.1mm clearance to accommodate different
thicknesses of material. (Max 1.5mm) Make sure to select the appropriate height adjustment before printing.
Height of the printing head
3
2
1
High
Low
Printing Mode
PHOTO:This is suitable for printing photographs.
SUPER: This is suitable for output with high image
quality, such as posters.
FINE: This is suitable for output with comparatively
high detail, such as posters.
FINE2:This is suitable for outputting posters and the
(Factorylike on various materials. [CAMMJET ONLY]
default)
NORMAL: This is suitable for printing large-size items
with comparatively high quality in a short
time.
FAST: This is suitable for printing large-size items in
a short time.
DRAFT: This can produce output in the shortest time. It
is suitable for checking layout and the like.
UNI-DIRECTION:
Uni-directional printing.
Printing is performed as the carriage moves from right to left.
Printing quality is better than with [BI-DIRECTION].
BI-DIRECTION (factory default):
Bi-directional printing.
Printing is performed as the carriage moves from right to left,
and also as it returns from left to right.
Printing speed is faster than with [UNI-DIRECTION].
Printing Direction
Press the [ ] key to make the setting for the printing
direction.
Use the [ ] and [ ] keys to display the printing
direction, then press the [ENTER] key.
3
DIRECTION
BI-DIRECTION
Press the [PRINTCONFIG] or [PRINT QUALITY] key.
1Use the [ ] and [ ] keys to choose the printing
mode.
2
PRINT MODE
FINE
Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.
4
Refer to yourCAMMJET/Hi-Fi JET user’s manual for detailed instructions on working with the unit.
4
Demo Print
Go to the Demo Print menu and press enter. Six squares will print and cut confirming proper setup
Quick-Start Complete
The CAMMJET or Hi-F JET is now ready to print. Refer to the User’s manual on connecting to your computer, software
installation. An ECP printer cable is included in the accessories kit, which requires ECP settings on an
LPT port. Refer to your computer manufacturer’s instructions on setting a parallel port to ECP.
Install a blade and load a material, then close the front
cover.
1Use the [ ] , [ ] , [ ] and [ ] keys to move
the tool carriage to the place where the test cutting is
to be performed.
2
Press the [TEST CUT] key for 1 second or longer.
Test cutting starts.
3
Examine the cutting results for the material and diagnose the cutting conditions.
4(1) Peel off the round section (marked by ).
When it can be peeled by itself, without disturbing the square (marked by ), the
cutter force is set appropriately.
If it peels, either the “blade force” or the “amount of blade extension” is insufficient.
(2) Remove the square section (marked by ).
The optimum blade pressure is correct if you can clearly make out the lines left by the
blade.
If the blade trace is indistinct or too strong, you need to adjust the “blade force” or the
“amount of blade extension.”
(3) Check the shape of the rectangle.
- If the corners are cut securely as shown in A, there conditions are correct.
- If the corners are rounded as shown in B, the “blade offset” is insufficient.
- If the corners have “horns” as shown in C, the “blade offset” is too large
ABC
Setup for Cutting
Other manuals for CammJet CJ-500
1
This manual suits for next models
1
Table of contents
Other Roland Printer manuals
Roland
Roland VersaStudio BN-20 User manual
Roland
Roland CAMM-1 PNC-950 User manual
Roland
Roland VersaSTUDIO BN-20D User manual
Roland
Roland Color Camm Pro PC-60 User manual
Roland
Roland Texart RT-640 User manual
Roland
Roland LEC-300A User manual
Roland
Roland Soljet Pro III XJ-640 User manual
Roland
Roland VersaUV LEF2-200 User manual
Roland
Roland TrueVIS SG2-640 Operating manual
Roland
Roland CJ-540 User manual
Roland
Roland VersaCamm SP-300V User manual
Roland
Roland TrueVIS VG2-640 Operating manual
Roland
Roland Soljet EJ-640 User manual
Roland
Roland iModela iM-01 Use and care manual
Roland
Roland VS-640 User manual
Roland
Roland SolJet Pro II V SC-545EXW User manual
Roland
Roland VersaCamm SP-540V User manual
Roland
Roland SOLJET PROIII XC-540 User manual
Roland
Roland Soljet Pro III XJ-540 Operating and maintenance manual
Roland
Roland Metaza MPX-60 User manual
