Rimage Prism User manual

Technical Procedure

Date 01/09/04

Installing a Prism Printer Ribbon

We recommend you store all ribbons at a temperature between 60°–95°F, and avoid moisture

or direct sunlight. If you are replacing the ribbon, now is a good time to clean the printhead.

Procedure

1. Power on the printer.

2. Remove the top cover.

3. Pull up the Take-up Roller so the end with the gear comes up first as shown

below, and remove the Take-up Roller out of the printer.

4. Remove the Supply Roller by pulling up on the end as shown.

InstallingPrismRibbon.doc 1 of 5

5. Slide the Print Ribbon onto the Supply Roller, as shown in the figure below.

Align the two Notches of the Cardboard Core to the Metal Pins on the Supply

Roller.

6. Peel the Ribbon Leader from the Supply Ribbon.

8. Pass the Ribbon Leader under the Ribbon Guide (metal shaft) as shown.

9. Tape the Ribbon Leader to the back of the Printer Drawer as shown above.

InstallingPrismRibbon.doc 2 of 5

10. Install Supply Roller as shown. Leave some slack in the ribbon leader.

11. Push the Unit Attention button so that the printer drawer comes out. This

automatically threads the ribbon to the front of the printer.

12. Remove the tape from the Printer Drawer.

13. Remove the adhesive strip from the ribbon leader.

InstallingPrismRibbon.doc 3 of 5

14. Place the new empty Cardboard Core on the Take-up Roller. It is notched to

fit only one way.

15. Place the Take-up Roller on top of the Ribbon Leader as shown. The gear must

be on the correct side.

16. Pull the Ribbon Leader up over the Cardboard Core and attach the Adhesive

Strip to the Cardboard Core so the edges on the Ribbon Leader are aligned to

the edges of the Cardboard Core. The arrow below illustrates the wrap

direction.

InstallingPrismRibbon.doc 4 of 5

17. Roll up the ribbon leader so it is wrapped only once around the roller. Do not

go past the marking on the leader that states – STOP - Wind Leader Onto

Take-up Core Stopping here.

18. Install the cardboard Take-up Roller in the printer as shown. At this time, the

ribbon should be tight and there should be no creases in the ribbon.

19. Install the Take-up Roller in the printer and press down firmly until the Take-

up Roller snaps into place.

20. The “STOP - Wind Leader Onto Take-up Core Stopping here” marking on the

Ribbon Leader should not be rolled onto the take-up roller. The marking

should not be past the point shown in the above picture. If the marking is on

the roller, pull the Take-up Roller out and roll back the ribbon. Take up the

slack by rolling the supply roller back.

21. Press the Unit Attention button to close the drawer. The ribbon should be

pulled tight after it runs the ribbon validation process.

22. Install the top cover.

InstallingPrismRibbon.doc 5 of 5

Other manuals for Prism

5

Table of contents

Other Rimage Printer manuals

Rimage

Rimage Desktop 360i User manual

Rimage

Rimage Amigo II Manual

Rimage

Rimage Everest Quick start guide

Rimage

Rimage Amigo II User manual

Rimage

Rimage EverestTM Printer User manual

Rimage

Rimage Everest III User manual

Rimage

Rimage Amigo II Installation instructions

Rimage

Rimage Autostar II User manual

Rimage

Rimage Desktop 360i User manual

Rimage

Rimage Allegro 100 User manual

Rimage

Rimage Autostar II User manual

Rimage

Rimage CDPR6 User manual

Rimage

Rimage Prism User manual

Rimage

Rimage Desktop 360i User manual

Rimage

Rimage PrismPlus! User manual

Rimage

Rimage Everest User manual

Rimage

Rimage Prism Instruction Manual

Rimage

Rimage Everest III User manual

Rimage

Rimage Prism User manual

Rimage

Rimage Everest Encore Operating and safety instructions

Rimage

Rimage Autostar II Operating and safety instructions

Rimage

Rimage Amigo II Operating and safety instructions

Rimage

Rimage Desktop 360i Operating and safety instructions

Rimage

Rimage Professional 3400 User manual

Popular Printer manuals by other brands

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series quick start guide

Evolis

Evolis Elypso user guide

Kyocera

Kyocera FS-9530DN specification

Canon

Canon LASER SHOT LBP-1210 Specifications

Samsung

Samsung BIXOLON SRP-350plusF user manual

Canon

Canon PIXMA PRO-1 Series Getting started

Canon

Canon PIXMA G3560 Online manual

Dell

Dell Color Laser Printer 2130cn user guide

Tektronix

Tektronix Phaser 840 user guide

Epson

Epson ET-7750 Programming guide

Canon

Canon CLBR 460ps Service manual

Eltron

Eltron P210 Guide manual

Ricoh

Ricoh MD-P1 Service manual

Epson

Epson SC-F7100 series user guide

Epson

Epson Stylus C40UX Service manual

Canon

Canon imagePASS-A2 Service guide

Canon

Canon S820D user guide