RH LUCE Programming manual
LUCE FLOOR MIRROR
42" x 78" (107cm x 198cm)
ASSEMBLY & I NSTAL L AT I ON I NSTRUCT I ONS
ENGLISH
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
LUCE FLOOR MIRROR
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
CAUTION:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety.
It is important that they are read carefully and
completely before installation of the fixture.
4. For your safety, it is recommended that two
people hang the fixture.
5. Check with a professional to ensure your wall
can tolerate a fixture weighing 104 Ibs (48 kg).
6. When wall mounting, stud mounting is
strongly recommended.
PARTS INCLUDED
(A) Mirror With Bracket (1)
(B) Bracket (2)
(C) Clevis pin (4)
(D) Hair pin (4)
(E) Stainless steel screw (4)
(F) Steel screw (8)
(G) EZ mini anchor (12)
(H) Aluminum hanger (1)
(J) Metal cord (2)
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
INSTALLATION OF MIRROR
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on the
wall surface using the holes in the aluminum hanger (H) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (G).
4. Insert the EZ mini anchors (G) into the holes on the wall.
5. Mount the aluminum hanger (H) into the wall using screws (F).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
8. Installation is complete.
WALL
BACKSIDE
FIGURE 1
WALL
F
H
G
F
G
A
Mirror
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH OTHER.
A LEVEL CHECK IS HIGHLY RECOMMENDED. CHECK AND ADJUST
IF NEEDED.
INSTALLATION OF MIRROR
LEANING
1. Move the mirror into position close to the wall. Mark locations on
the wall approximately 5" (13 cm) above the set of metal brackets
attached on mirror. Move mirror away from the wall. Drill pilot holes
with a 3/32" (3 mm) drill bit if needed. Install EZ mini anchors (G)
into the holes, and then attach brackets (B) to the wall with the
screws (E) provided. (Figure 1).
2. Move the mirror into it's final position, taking care to line up the wall
brackets with the mirror brackets. Attach the metal cord (J) into
bracket with clevis pin (C) and hair pin (D). (Figure 2).
3. Important: Check to ensure that the wall brackets are firmly screwed
into the wall, the mirror brackets are firmly attached to the frame.
FIGURE 2
OK NOT OK
FIGURE 3
FIGURE 1
G
B
E
WALL
D
C
J
FIGURE 2
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
**NOTE: When leaning the mirror, we recommend installing the Anti-Tip
Kit. When hanging, simply follow the instructions above. The Anti-Tip
Kit is not necessary.
FIGURE 3
BACKSIDE
FIGURE 4
WALL
MIRROR
LUCE M I RROR ENGLISH
RH.COM
REVISION 04/23/22
WARRANTY
If you are not completely satisfied with your purchase, please contact
us to return or exchange your item(s) within 30 days of the delivery
date, with proof of purchase. Note that returns or exchanges are not
accepted for special orders, items that have been installed, mattresses
and/or foundations no longer in their original packaging, and other
items listed below. Other exclusions may apply. Contact us for details.
Unfortunately, galleries cannot accept returns of furniture or other large
items.
CARE INSTRUCTIONS
1. To clean, use a soft dry or damp cloth.
2. Do not use abrasive cleaners.
LUCE FLOOR MIRROR
24" x 80" (61cm x 203cm)
ASSEMBLY & I NSTAL L AT I ON I NSTRUCT I ONS
ENGLISH
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
LUCE FLOOR MIRROR
STORAGE
1. Do not stack anything on top of the mirror.
2. Keep the mirror packaged until installation.
3. Store mirror upright on the long edge.
MIRROR HANDLING INSTRUCTIONS
CAUTION:
1. Remove vertically from package.
2. Always carry mirror vertically as illustrated
Carrying flat will cause breakage.
BEFORE YOU BEGIN
1. Professional installation recommended.
2. Tool and materials required:
Carpenter's level
Phillips head screwdriver
3. These instructions are provided for your safety.
It is important that they are read carefully and
completely before installation of the fixture.
4. For your safety, it is recommended that two
people hang the fixture.
5. Check with a professional to ensure your wall
can tolerate a fixture weighing 64 Ibs (30 kg).
6. When wall mounting, stud mounting is
strongly recommended.
PARTS INCLUDED
(A) Mirror With Bracket (1)
(B) Bracket (2)
(C) Clevis pin (4)
(D) Hair pin (2)
(E) Stainless steel screw M4 x 30 (4)
(F) Steel screw M4 x 30 (8)
(G) EZ mini anchor (12)
(H) Aluminum hanger 18" (46 cm) (1)
(I) Aluminum hanger 30" ( 77 cm) (1)
(J) Metal cord (2)
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
INSTALLATION OF MIRROR
WALL MOUNTING
1. Unpack all parts and place them on a protected work surface.
2. Determine the exact location of the fixture and mark the holes on
the wall surface using the holes in the aluminum hanger (H) (vertical
mounting) or (I) (horizontal mounting) as a guide.
3. Drill small holes on each point location on the wall.
Each hole should be just large enough to accommodate EZ mini
anchor (G).
VERTICAL MOUNTING
HORIZONTAL MOUNTING
4. Insert the EZ mini anchors (G) into the holes on the wall.
5. Mount the aluminum hanger (H) or (I) into the wall using screws (F).
6. Check that the aluminum hanger fixture is securely screwed into the
wall.
7. Place the mirror with hanger cleat (A) into the aluminum hanger
fixture.
8. Installation is complete.
FIGURE 1
MIRROR
Wall
Wall
BACKSIDE
A
F
F
H
G
G
FIGURE 2
Wall
BACKSIDE
Wall
G
G
F
F
I
MIRROR
LUCE FLOOR M I RROR ENGLISH
RH.COM
REVISION 04/23/22
**NOTE: MAKE SURE THAT THE TWO (2) CLEATS (1 ON MIRROR
AND 1 ON WALL) ARE LOCKED AND SECURED WITH EACH OTHER.
A LEVEL CHECK IS HIGHLY RECOMMENDED. CHECK AND ADJUST
IF NEEDED.
INSTALLATION OF MIRROR
LEANING
1. Move the mirror into position close to the wall. Mark locations on
the wall approximately 5" (13 cm) above the set of metal brackets
attached on mirror. Move mirror away from the wall. Drill pilot holes
with a 3/32" (3 mm) drill bit if needed. Install EZ mini anchors (G)
into the holes, and then attach brackets (B) to the wall with the
screws (E) provided. (Figure 1).
2. Move the mirror into it's final position, taking care to line up the wall
brackets with the mirror brackets. Attach the metal cord (J) into
bracket with clevis pin (C) and hair pin (D). (Figure 2).
3. Important: Check to ensure that the wall brackets are firmly screwed
into the wall, the mirror brackets are firmly attached to the frame.
FIGURE 4
OK NOT OK
FIGURE 3
FIGURE 1
G
B
E
WALL
D
C
J
FIGURE 2
Other manuals for LUCE
1
Table of contents
Other RH Indoor Furnishing manuals
RH
RH Logic 400 User manual
RH
RH Focus User manual
RH
RH Secur24 User manual
RH
RH BECKMAN RECTANGULAR CHANDELIER 54 User manual
RH
RH ASTON QUEEN BED User manual
RH
RH METAL BEVELED MEDICINE CABINE Instruction manual
RH
RH LUCIDA COFFEE TABLE User manual
RH
RH ASPEN PARSONS User manual
RH
RH LUCE Programming manual
RH
RH INDIAN FORTRESS BED User manual
RH
RH NICCOLO User manual
RH
RH Focus User manual
RH
RH PESARO User manual
RH
RH UTILITAIRE TASK TABLE LAMP Instruction manual
RH
RH Logic 400 User manual
RH
RH Mereo User manual
RH
RH ESSEX TRACK WINDOW User manual
RH
RH Mereo User manual
RH
RH MAISON PANEL KING BED User manual
RH
RH 18TH C. SPINDLE TURNED QUEEN BED User manual
