Response RE5000AD User manual

Introduction

When connected to the RE5000 Control Unit, the

RE5000AD may be used to communicate up to three

separate message phrases (usually relating to Intruder,

Fire and Medical Alert conditions). The Dialler Tamper

Switch may be connected to Zone 6 on the RE5000CU

if tamper protection is required.

The Communicator Interface Cable connection supplied

with the RE5000 Control Unit allows simple connection

between the Control Unit and Dialler.

THE FOLLOWING MUST BE READ IN CONJUNCTION

WITH THE RE5000AD (TSD1+) INSTALLATION AND

OPERATING INSTRUCTIONS SUPPLIED AND THE

RE5000 INSTALLATION AND OPERATING MANUAL.

CONNECTING THE RE5000AD TO

THE RE5000 CONTROL UNIT.

Disconnect all power (Mains and Back-up Battery)

from the Control Unit before making any connections.

2. Plug the Interface Cable into the Control Unit plug

and connect the lead to the Dialler as shown.

3. Ensure that all cabling is connected correctly and that

all unused cores of the Interface Cable are cut back or

insulated to prevent accidental short circuits.

4. Connect the Telephone Cable to the Dialler - (see

Dialler Installation Instructions).

5. Reconnect power to the Control Unit and proceed to

programme and test the Dialler in accordance with

the Dialler Operators Manual.

Note:

If your RE5000CU is supplied with an 8-Core

interface cable, please call our Technical

Helpline for connection advice.

Loudspeaker Tamper

Switch Microphone

Set Trig Polarity

Link to '+' for

negative trigger

to suit RE5000CU

trigger output

Telephone Line

Connection Terminals

Factory

Restart Pins

Factory Restart

0/P1

+12V

TRIGGER

POLARITY

A B A1 B1

TELEPHONE CONNECTIONS

TAMP ABORT C B A

TRIG INPUT

TSD1

Optional Dialler Tamper Connection

To Zone 6 Hard Wired Zone Input

on RE5000CU

9-Core Interface Cable

Red +12V

Blue

Grey

Brown

Orange

Yellow

Green

Mauve

White

AC Power

Failure

– 0V

Arm

Disarm

Low Batt

Intruder

Fire

Medical Alert/

Personal Attack

Control Unit

Terminal Block

Plu

-in Connector to Control Unit PCB

N.O.

COM

N.C.

V+

GRD

Zone 6

Siren

Charge

Tamper

Communicator

Interface Cable

Connection

Connections for 9-Core Interface Cable

CORE

Using the RE5000AD with a

RE5000 System Control Unit

Installation and Operating Instructions

Introduction

When connected to the RE3000 Control Unit, the

RE5000AD may only be used to communicate one

message phrase associated with the Alarm Activation -

(usually relating to an Intruder Alarm Condition).

This message phrase will be made up of the common

phrase O and message phrase A. Message phrases B,

C and D will not be used in this instance.

THE FOLLOWING MUST BE READ IN CONJUNCTION

WITH THE RE5000AD (TSD1+) INSTALLATION AND

OPERATING INSTRUCTIONS SUPPLIED AND THE

RE3000 INSTALLATION AND OPERATING MANUAL.

CONNECTING THE RE5000AD TO THE

RE3000 CONTROL UNIT.

1. Disconnect all power (Mains and Back-up Battery)

from the Control Unit before making any connections.

2. Connect the 4 core cable supplied with the Dialler to

the Control Unit as shown.

3. Ensure that all cabling is connected correctly. Cut

back or insulate any unused cable cores to prevent

short circuits.

4. Connect the Telephone Cable to the Dialler - (see

Dialler Installation Instructions).

5. Reconnect power to the Control Unit and proceed to

programme and test the Dialler in accordance with

the Dialler Operators Manual.

Loudspeaker Tamper

Switch Microphone

Set Trig polarity Link to '–'

for negative trigger to suit

RE3000CU trigger output

Telephone Line

Connection Terminals

Factory

Restart Pins

Red

Black

Yellow

Terminals inside

RE3000 Control Unit

NO 1

C 2

NC 3

Power (–) 4

Power (+) 5

4-Core Cable

(Blue wire not used)

Install link wire between

terminals 2 and 4

Red

Black

Yellow

Factory Restart

0/P1

+12V

TRIGGER

POLARITY

A B A1 B1

TELEPHONE CONNECTIONS

TAMP ABORT C B A

TRIG INPUT

TSD1

Using the RE5000AD with a

RE3000 System Control Unit

WA_08.04 CA2000AD

Wireless Alarms. 17Church Road, Great Bookham, Surrey KT23 3PG

Telephone: 01372 450960 E-mail: [email protected] www.wireless-alarms.net

0359

RADIO DEVICES FOR USE IN THE UK

HELPLINE

If you need help, just dial for

expert technical support

01372 450960

(Lines open 9.00am to 6.00pm, Monday to Friday).

This manual suits for next models

Table of contents

Other Response Security System manuals

Response

Response SL2 Installation instructions

Response

Response CWFK1/CA3 User manual

Response

Response SA5 E User manual

Response

Response ML6 User manual

Response

Response SA1 E Installation instructions

Response

Response CWK6 User manual

Response

Response SL5 Installation instructions

Response

Response QC 3670 Technical manual

Response

Response CWK5 User manual

Response

Response Protector P500S Installation instructions

Response

Response CWD3 User manual

Response

Response CENTURION SCOUT User manual

Response

Response SA1 E User manual

Response

Response SL3 User manual

Response

Response SA3 E PLUS User manual

Response

Response RE3000S User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual