Quantum PX500 Series User manual
81-81301-04 A01, August 2006 1
Quantum PX500
Series Tape Drive
Installation Instructions
Introduction 3
Tape Drive Numbering................................................................................ 3
Upgrade Kits.................................................................................................. 6
Required Tools .............................................................................................. 6
Unpacking the Tape Drive 7
Installing the Tape Drives 7
Cabling the Tape Drives 8
PX502 Libraries.............................................................................................. 9
PX506 Libraries............................................................................................ 11
PX510 Libraries............................................................................................ 13
Setting the Tape Drive SCSI ID 15
Setting the SCSI ID Using the OCP .......................................................... 15
Setting the SCSI ID from the Remote Management Pages ................... 16
Completing the Native Fibre Channel Installation 18
Determining the WWNs World Wide Names........................................ 18
Verifying Library Connectivity................................................................. 22
Fibre Channel Connectivity Troubleshooting 24
Fibre Channel Connectivity Troubleshooting ........................................ 24
SCSI ID Assignment with Native Fibre Channel Tape Drives............. 25
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
Made in the USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to
the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to
time without notice.
COPYRIGHT STATEMENT
© Copyright 2006 by Quantum Corporation. All rights reserved.
Your right to copy this document is limited by copyright law. Making copies or adaptations without prior written authorization of Quantum
Corporation is prohibited by law and constitutes a punishable violation of the law.
TRADEMARK STATEMENT
Capacity on Demand (CoD), Crosslink Mechanism, DLT, DLTSage, DLTtape, Super DLTtape, Performance on Demand, (PoD), PRISM,
PRISM Storage Architecture logo, SiteCare, StackLink, StorageCare, SuperLoader, and ValueLoader are all trademarks of Quantum
Corporation. Quantum, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation.
Other trademarks may be mentioned herein which belong to other companies.
2
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
Introduction 3
Introduction 0
This document provides instructions for adding a tape drive to an Quantum
PX500 Series tape library. The tape drive upgrade procedure consists of the
following steps:
•Unpacking the Tape Drive
•Installing the Tape Drives
•Cabling the Tape Drives
•Setting the Tape Drive SCSI ID
•Completing the Native Fibre Channel Installation
•Fibre Channel Connectivity Troubleshooting
Tape Drive Numbering 0The Quantum PX500 Series tape library may contain up to 10 tape drives
depending on the library model. Refer to the following figures:
•Figure 1 - PX502 Tape Drive Numbering (up to two tape drives)
•Figure 2 - PX506 Tape Drive Numbering (up to six tape drives)
•Figure 3 - PX510 Tape Drive Numbering (up to ten tape drives)
Figure 1 Quantum PX502
Tape Drive Numbering
Tape drive 2 Tape drive 1
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
4 Introduction
Figure 2 Quantum PX506
Tape Drive Numbering
Tape
drive 2
Tape
drive 4
Tape
drive 6
Tape
drive 1
Tape
drive 3
Tape
drive 5
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
Introduction 5
Figure 3 Quantum PX510
Tape Drive Numbering
Tape
drive 2
Tape
drive 4
Tape
drive 6
Tape
drive 1
Tape
drive 3
Tape
drive 5
Tape
drive 8
Tape
drive 10
Tape
drive 7
Tape
drive 9
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
6 Introduction
Upgrade Kits 0The tape drive upgrade kit differs depending on the tape drive type needed
for the library (refer to table 1):
Table 1 Tape Drive
Upgrade Kits
Required Tools 0The following tools are required to perform the tape drive upgrade
procedure:
• Flat blade screwdriver
Part Number PC-UUBQA-YF (SDLT320, SCSI)
PR-UU1QA-YF (SDLT600, SCSI)
PR-UU4QC-YF (SDLT600, Native Fibre)
PC-UUAQA-YF (DLT-S4, SCSI)
PC-UU8QC-YF (DLT-S4, Native Fibre)
PR-UU2QA-YF (HP LTO2, SCSI)
PR-UU3QA-YF (HP LTO3, SCSI)
PR-UU5QC-YF (HP LTO3, Native Fibre)
SDLT320/600 and DLT-S4
Tape Drive Module
HP-LTO2/3 Tape Drive
Module
Caution: Use appropriate electrostatic discharge (ESD) precautions
when installing the tape drive.
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
Unpacking the Tape Drive 7
Unpacking the Tape Drive 0
To unpack the tape drive:
1Open the shipping carton.
2Remove the tape drive from the carton.
The tape drive is protected by two pieces of foam and an antistatic bag.
3Remove the foam from the wrapped tape drive. Remove the tape drive
from the antistatic bag.
Installing the Tape Drives 0
To install tape drives in a PX500 Series library:
1At the back of the library, use a flat blade screwdriver to loosen the
captive screws that secure the cover plate to the empty drive bay.
2Set the cover plate aside.
3Insert the tape drive into the drive bay slowly until the connectors are
seated (see figure 4).
4Tighten the tape drive captive screws using a flat blade screwdriver.
5Repeat steps 1through 4to install another tape drive in a different
location, if desired.
Note: If this is an initial library installation, it is recommended to turn
the library off prior to installing tape drives. If this is an existing
library that is receiving a tape drive upgrade, the library can
remain powered on.
Note: Each tape drive ships from Quantum with a version of library
firmware as well as drive firmware on the tape drive interface
PWA. When you install the tape drive, the library will check the
version of library firmware on the tape drive and verify if the
firmware is newer than the version currently running. If the
library firmware on the tape drive is newer than the version
currently running on the library, the OCP will prompt you with
the option to upgrade the library firmware.
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
8 Cabling the Tape Drives
Figure 4 Installing a Tape
Drive
Proceed to Cabling the Tape Drives.
Cabling the Tape Drives 0
After the tape drive(s) have been installed, you must connect SCSI or Fibre
Channel cables to each drive.
Refer to the following figures to cable the tape drives:
•PX502 Libraries on page 9
• SCSI tape drives (see figure 5)
• SCSI tape drives in surrogate mode (see figure 6)
• Native Fibre Channel tape drives (see figure 7)
•PX506 Libraries on page 11
• SCSI tape drives (see figure 8)
• Native Fibre Channel tape drives (see figure 9)
•PX510 Libraries on page 13
• SCSI tape drives (see figure 10)
• Native Fibre Channel tape drives (see figure 11)
Tape drive 1
Captive screw
Tape drive 2 Captive screw
PX502 shown
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
Cabling the Tape Drives 9
PX502 Libraries 0The following figures illustrate tape drive cabling for the PX502 libraries
Figure 5 Cabling the Tape
Drives in a PX502 Library
(SCSI)
Figure 6 Cabling the Tape
Drives in a PX502 Library
(SCSI Surrogate)
SCSI jumper cables
SCSI terminator
Host computer
Tape
drive 1
Tape
drive 2
SCSI jumper cables
SCSI terminator
Host computer
Tape
drive 1
Tape
drive 2
Quantum PX500 Series Tape Drive Installation Instructions
81-81301-04 A01
August 2006
10 Cabling the Tape Drives
Figure 7 Cabling the Tape
Drives in a PX502 Library
(Native Fibre Channel)
Fibre Channel host/SAN
Tape
drive 1
Tape
drive 2
LTO-2, -3 native Fibre Channel drives
shown. SDLT 600 and DLT-S4 native
Fibre Channel drives have only one
FC port
Fibre Channel host/SAN Fibre Channel host/SAN
Other manuals for PX500 Series
6
This manual suits for next models
3
Table of contents
Other Quantum Storage manuals
Quantum
Quantum DLT 4700 User manual
Quantum
Quantum Scalar i6000 User manual
Quantum
Quantum ValueLoader LTO-1 User manual
Quantum
Quantum RDX 8000 User manual
Quantum
Quantum Scalar i6000 User manual
Quantum
Quantum Scalar LTFS Parts list manual
Quantum
Quantum DXi7500 Technical manual
Quantum
Quantum DAT 72 User manual
Quantum
Quantum DXi4500 User manual
Quantum
Quantum StorNext QM1200 User manual
Quantum
Quantum DLT 2500 User manual
Quantum
Quantum Travan 20GB User manual
Quantum
Quantum LTO 2U Instruction sheet
Quantum
Quantum DAT 320 CD320UE User manual
Quantum
Quantum DLT-V4 User manual
Quantum
Quantum LTO3 A-Series User manual
Quantum
Quantum DLTtape DLT 7000 User manual
Quantum
Quantum Scalar i500 User manual
Quantum
Quantum Scalar LTFS Use and care manual
Quantum
Quantum StorNext QD7000 Manual
