Pyle PLCM6000 User manual
PLCM6000
Video(out)
12V (in)
Mirror Enable
Short circuit (default)= Mirror Image
Open circuit = Inverse Image
封二空白
第5页
Read this manual for safety, and use the product correctly.
This product is designed for DC 12V vehicles. Make sure of the
correct power voltage.
This product works within the temperature range of 0°C~50°C.
Sometimes the picture may appear dim at the beginning of working at
lower temperature, but it turns to normal within a few minutes.
Do not disassemble or change the product. Disassembling or change
of the product may cause fire accident or electric shock. Further,
disassembling or change cannot be covered by the after service
guarantee.
Make sure of the safety of the driver and the passengers of the car in
when installing the product in the car.
Do not use the product while the engine is off. Otherwise, the battery
may be discharged.
Keep the sound volume at the normal level so that the sound may not
disturb the driver.
For safety, do not operate the product while driving the car.
The rear view may be reversed due to the type of some rear view
cameras; therefore, be careful not to rely upon the monitor picture
while driving the car. Additional special equipments are needed for
DC 24V vehicles, since.
This product is used only for DC 12V vehicle, in case of using at DC
24V vehicle, the special inverter is required.
第1页第4页
POWER ON/OFF
VIDEO SELECT
NEGATIVE ADJUSTMENT
MENU
POSITIVE ADJUSTMENT
MODE SELECT
1
2
3
4
5
6
Red to battery +12V
Black to grounding
Green to Reversing line
Yellow to Video 1
Yellow to Video 2
Red to Audio 1
White to Audio 2
Fush
AV-1 INPUT
VIDEO: YELLOW
AUDIO: RED
AV-2 INPUT
VIDEO: YELLOW
AUDIO: WHITE
POWER INPUT & REAR VIEW SIGNAL INPUT
RED WIRE: ACC +12V
BLACK WIRE: CHASSIS GROUND
GREEN WIRE: REVERSING
(1) Install clips of the R.V.M to bottom of existing mirror in the vehicle. Push
R.V.M carefully upward until below clip locks on to top part of existing mirror.
(2) Adjust R.V.M for optimum viewing angle and check the clips for proper
mounting.
- Check the R.V.M position; made sure it does not impede the driver or
passenger of the vehicle.
(3) Connect cables by matching the arrows on the cable and arrange the cables
into proper place for not impeded to driver of passenger.
* R.V.M: Rear View Mirror (Monitor)
第3页第2页
Other Pyle Car Video System manuals
Pyle
Pyle PYLE View Series PLHR4M User manual
Pyle
Pyle PLDVD130 User manual
Pyle
Pyle PLDVSL7 User manual
Pyle
Pyle View PLRTD155 User manual
Pyle
Pyle PLRD143F User manual
Pyle
Pyle PLTVD7P User manual
Pyle
Pyle PLTS79BT User manual
Pyle
Pyle PLHRDVD101KT User manual
Pyle
Pyle PLD43MU User manual
Pyle
Pyle View PLDVD10M User manual
Pyle
Pyle PLVIN65 User manual
Pyle
Pyle PLD162 User manual
Pyle
Pyle PLDN74BTI User manual
Pyle
Pyle PLVW1443R User manual
Pyle
Pyle PLDVD124 Installation instructions
Pyle
Pyle PLTV7R User manual
Pyle
Pyle PLM4135BT User manual
Pyle
Pyle PLVWR1752 User manual
Pyle
Pyle PLD142 User manual
Pyle
Pyle PLDVD65IN User manual
