6
8
5
Pairing With an Audio Accessory
Troubleshooting
Pairing With a PRYMEBLU Adapter
7
STATUS LED MESSAGES
The meanings of the various status LED messages shown by the PRYMEBLU PTT are shown
on the following table:
LED INDICATION
Long (5 second) blue ash
Rapid blue ashing in 3 second bursts
One blue ash every 3 seconds
Two blue ashes every second
Rapid blue ashes for 3 seconds
Red
Single ash followed by 5 seconds
of rapid ashing
Blue Flashes while Red shows constantly
MEANING
PTT Powered On
Unpaired operation
Normal (paired) operation
Pairing Mode
Pairing successful
Push-to-Talk activated
Lost connection
Unpaired operation
Low battery or hardware failure
My PRYMEBLU PTT will not pair with the PRYMEBLU Adapter.
Follow the instructions to place the PRYMEBLU Adapter into the correct pairing mode and then
activate the pairing mode on the PRYMEBLU PTT. Make sure that the PRYMEBLU Adapter and PTT
are within one meter of each other. Make sure that all other nearby Bluetooth devices are turned
o. These devices can interfere with the pairing process.
My PRYMEBLU PTT worked ne before, but is not working now.
Ensure that your PRYMEBLU PTT has a fully charged battery and is turned on. Ensure that the
Bluetooth headset is powered on and paired with the PRYMEBLU Adapter. If the devices will still
do not work, re-pair the PRYMEBLU Adapter, Bluetooth Headset, and PRYMBLU PTT.
After Charging, My PRYMEBLU PTT Does Not Power Up
Power cycle the PRYMEBLU PTT by setting the power switch to O, waiting twn seconds, and then
turn the power switch On. The PRYMEBLU PTT should now operate normally. Always make sure
that the power switch on the PRYMEBLU PTT is turned to the O position when charging.
SUPPORT AND WARRANTY
PRYME Radio Products warrants this product against defects in materials or workmanship for a period
of one year from the date of retail purchase. PRYME will repair or replace a defective unit, at our
option, without charge for parts or labor. The limited warranty is extended only to the original
purchaser and is valid only to consumers in the United States and Canada. It does not cover damage
or failure caused by or attributable to Acts of God, abuse, misuse, improper or abnormal usage, faulty
installation, improper maintenance, lightning, or other incidences of excessive voltage, or any
tampering or repairs by other than a PRYME authorized repair facility. It does not cover replacement
of consumable parts, transportation costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms of this warranty.
This warranty can only be modied by an ocer of PRYME Radio Products, and then only in writing.
Should this product prove defective in workmanship or material, the consumer’s sole remedies shall
be such repair or replacement as provided by the terms of this warranty. Under no circumstances
shall PRYME Radio Products be liable for any loss or damage, direct, consequential, or incidental,
arising out of the use of or inability to use this product. Some states do not allow limitations on how
long an implied warranty lasts or the exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This warranty gives you
specic legal rights.
You may also have other rights, which may vary, from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-2654 or visit us on
the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2010 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® and PRYMEBLU™ are trademarks owned by PRYME Radio Products. All other product or
service names are the property of their respective owners.
DISCLAIMER: The Bluetooth wireless link used by PRYMEBLU products is an open standard, unsecured
technology. As such, it is not recommended for rst-responder or other mission critical users.
STEP TWO: Pairing the PRYMEBLU Adapter and Wireless Headset
In order to operate, the PRYMEBLU PTT must be paired to PRYMEBLU Adapter (BT-500 series).
However, The PRYMEBLU Adapter must rst be paired to a wireless Bluetooth headset. To pair these
devices, follow this procedure:
In order to operate, the PRYMEBLU PTT must be paired to PRYMEBLU Adapter (BT-500 series). The
PRYMEBLU Adapter must also be paired to a Bluetooth headset. To pair these devices, follow this
procedure:
* The PRYMEBLU Adapter must be connected to a compatible radio with a freshly charged battery.
Ensure the two-way radio, Bluetooth headset, and PRYMEBLU PTT are all powered o.
* Place the PRYMEBLU Adapter in Accessory Pairing mode. To do this, turn the two-way radio on while
holding down the Talk button on the PRYMEBLU Adapter. Continue to hold the Talk button down for
approximately three seconds. Release the Talk button when the status LED ashes two times per
second. The PRYMEBLU Adapter is now in audio accessory pairing mode.
* Activate the pairing mode on your Bluetooth headset by following the instructions provided by the
headset’s manufacturer. Once the wireless audio accessory and PRYMEBLU Adapter are paired with
each other, the status
LED on the PRYMEBLU Adapter will show a constant blue light for three seconds.
* Once the headset and PRYMEBLU Adapter have been successfully paired, turn o the two-way radio
and Bluetooth headset and wait at least three seconds.
STEP THREE: Pairing the PRYMEBLU PTT and PRYMEBLU Adapter
* Turn on the two-way radio while holding down the Talk button on the PRYMEBLU Adapter.
Continue to hold the Talk button down for approximately three seconds. Release the Talk button
when the status LED ashes two times per second. Then, press the Talk button again. The LED
should now ash three times per second, indicating that the PRYMEBLU Adapter is now in PTT
Pairing mode.
* Place the PRYMEBLU PTT in pairing mode by holding down the Push-To-Talk button while moving
the power switch to the On position. Continue to hold down the Push-To-Talk button until the LED
indicator on the PRYMEBLU PTT ashes blue continuously. You can then release the Push-to-Talk
button. The PRYMEBLU PTT is now in pairing mode.
* Once the PRYMEBLU Adapter and PRYMEBLU PTT are paired with each other, the status LED on the
PRYMEBLU Adapter will show a constant blue light for three seconds and the LED on the PTT will
show one blue ash every second.
* If the PRYMEBLU Adapter or PRYMEBLU PTT does not detect a compatible wireless accessory within
60 seconds of being put into pairing mode, the devices will exit the pairing mode and resume
normal operation.
* After pairing is successful, turn o the PRYMEBLU PTT and the two-way radio that the PRYMEBLU
Adapter is attached. Wait at least three seconds.
STEP FOUR: Testing and Using the PRYMEBLU PTT
After the Bluetooth headset, PRYMEBLU Adapter and PRYMEBLU PTT have been paired with each
other you can test and use them together:
* Turn on the two-way radio the PRYMEBLU Adapter is connected to.
* Turn on the Bluetooth headset. Within a few seconds the LED indicator on the PRYMEBLU Adapter
should show a long ash, indicating the Bluetooth headset and PRYMEBLU Adapter are connected.
* Turn on the PRYMEBLU PTT. The LED indicator on the PRYMEBLU PTT will ash rapidly. Within a
few seconds the LED indicator will show one blue ash per second, indicating that it is connected
wirelessly to the PRYMEBLU Adapter.
*You will now be able to operate using the wireless accessories. Pressing the Push-to-Talk button on
the PRYMEBLU PTT will cause the two-way radio to transmit. Transmit audio will be picked up by the
Bluetooth headset. Received signals will also be heard through the Bluetooth headset’s earphone.
