Precor Experience Series 700 Line User manual

Experience™ Series 700 Line Treadmill

Assembly Guide

Equation 1:E nglish

Treadmill Assembly Guide

Follow the steps in the order listed in this assembly guide. For more product

information, visit us at www.precor.com.

WARNING

At least two people are required to assemble the equipment.

DO NOT attempt assembly by yourself.

Assembly requirements

Important Before you fully tighten a fastener, check that its head is flush with the surface

of the equipment. Ifnot, cross-threading may have occurred. DONOT attempt to rework the

assembly as more damage to the equipment will occur. Instead, contact Customer Support

at www.precor.com.

We recommend you:

•Assemble the equipment close to where you plan to use it.

•Assemble the equipment on a solid, flat surface, so that it remains level and

stable.

•Locate the equipment at least 19.7 inches (0.5 meter) away from walls or

furniture on either side of the equipment, and 19.7 inches (0.5 meter) away

from objects behind or in front of the equipment.

•DO NOT move the equipment without assistance.

Hardware kit

Component Quantity Torque Component Quantity Torque

Washer

(3/8-inch)

Plastic grommet

(1/4-inch)

Self-tapping pan head screw

(1/4 x 1-inch)

Washer (3/8-inch) 12

Self-tapping pan head screw

(1/4 x .75-inch)

Button head screw

(3/8 x 1-inch)

12 25 ft-lb

Hex head cap screw

(3/8 x 5/8-inch)

6 25 ft-lb

Note There may be extra hardware included with the treadmill.

Begin Assembly

WARNING

DO NOT attempt to connect electrical power until all assembly procedures are complete and console is properly installed.

Important Before unpacking the treadmill, follow the ramp assembly instructions

(included in the box) to build and use a custom ramp to safely and securely roll the

treadmill base off the shipping pallet.

To attach the uprights to the treadmill:

1. Remove the hood from the treadmill base and set it aside.

2. Position a base side cover against the treadmill frame so that the tabs fit into the

frame.

Figure 1

3. Using a #3 Phillips head screwdriver, attach the base side cover using

one screw for the side attachment and one screw for the front

attachment.

Figure 2

4. Position the right upright support near the base frame and route the data cable

inside of the base side cover and up through the right upright.

Important DO NOT pinch or crush the cable during assembly.

Figure 3

5. Position the right upright support onto the base frame so that the support lip fits

inside the frame and attach it using three screws and three washers .

Partially tighten.

Figure 4

6. Repeat Steps 3 through 5 to attach the left upright support.

Note Route PVS and console cables up the left upright support. Be careful not

to pinch the cables.

To attach the dash:

1. With assistance, set the dash assembly on top of the upright supports.

Note The dash slips down into the uprights. Pull it up slightly so that the screw

holes line up correctly.

2. Attach the dash assembly to each upright using three screws and three

washers . Partially tighten.

Figure 5

3. Fully tighten all 12 screws to 25 ft-lb. Tighten the lower upright screws in the

order shown in Figure 6.

Figure 6

To complete the dash assembly:

1. Remove the two screws from the back of the dash cover. Remove the dash cover

and set it aside with the screws.

2. Route the data cable through the right tube of the dash assembly, up the back

frame, and out through the top hole.

Note If you are attaching a PVS or networked console, route those cables

through the left side of the dash assembly at this time.

Figure 7

To attach the heart rate bar:

1. Position the heart rate bar assembly against the dash frame and attach it using

two screws and two washers . Partially tighten the fasteners.

Figure 8

2. Route the heart rate cable up through the back frame and out through the top

hole.

3. Remove the screw from the bottom of the tread arm.

Figure 9

4. Fit the tread arm into the heart rate bar and against the dash assembly.

Attach it using two screws and two washers . Use a hex key to

partially tighten the screws.

Figure 10

5. Attach the underside of each heart rate arm using one screw .

Fully tighten.

Figure 11

6. Repeat Steps 3 through 5 to attach the other arm and then fully

tighten screws to 25 ft-lb.

Touchscreen consoles only

To attach the filter to the drive power cable:

1. Disconnect the existing power cable from the drive unit, power filter, and ground

terminal. Then completely remove it from the treadmill.

Figure 12

2. Connect the new power cable according to Figure 13 and Table 1.

Figure 13

Table 1

Position Connector

Drive input connectors

Brown lead with quick-connect terminal

Blue lead with quick-connect terminal

Green and yellow lead with quick-connect terminal

AC input cable to the power cable

3. Use the Velcro fasteners to attach the power supply to the right side of the front

cross member on the treadmill base. Plug the AC input cable into the socket on

the power supply.

4. Route the DC output cable through the cable ties behind the power supply,

toward the upright support on your right. Bend the cable ties over the DC output

cable to hold it in place.

Note Bundle the excess cable and secure it under the cable clips.

5. Connect the black, AC power cable on the AC wiring harness to the socket on

the power supply.

Important The touchscreen console includes an accessory jack panel that you must

install on the treadmill. The panel connects the TV and Ethernet cables to the facility’s

network.

To install the accessory jack panel:

1. Remove the screws securing the blank plate at the right-front corner of the

treadmill. Discard the blank plate.

Figure 14

2. Thread the cable assembly down through the channel in the upright support on

your right. Drape excess cable over the inside edge of the support and tape into

place, if necessary.

Figure 15

3. Pass the lower end of the TV cable through the right-hand grommet, and insert it

into the connector inside the jack panel. Use a 7/16-inch torque wrench to

tighten the connectors to 30 in-lb.

4. Pass the lower end of the Ethernet cable through the right-hand grommet and

snap it into the eight-pin coupler in the jack panel.

5. Fit the lower ends of any optional console cables into the notch in the upper edge

of the jack panel.

6. Replace the panel and fully tighten the corresponding screws.

7. Place the hood onto the treadmill. Using a #3 Phillips head screwdriver, attach it

using four screws . Fully tighten.

Figure 16

To attach the safety key assembly:

1. Fit the bottom part of the safety key assembly onto the bottom of the dash

assembly and heart rate arms.

2. Position the top piece of the safety key assembly on top of the bottom part.

Figure 17

3. Attach the top part of the safety key assembly using two screws .

Figure 18

4. Insert two grommets into each of the dash arms, just above each upright

support.

Figure 19

5. Attach the front arm cover using four screws .

Figure 20

6. Attach the bottom arm cover using four screws .

Figure 21

7. Repeat Steps 4 through 6 to attach the covers to the other arm.

Other manuals for Experience Series 700 Line

Table of contents

Other Precor Treadmill manuals

Precor

Precor 9.35 User manual

Precor

Precor M9.57 User manual

Precor

Precor TRM 211 Technical manual

Precor

Precor 9.21 User manual

Precor

Precor Cycles Integrated LCD Screen Option none User manual

Precor

Precor 9.45 User manual

Precor

Precor Experience 700 line Series User manual

Precor

Precor C942 User manual

Precor

Precor 9.33 User manual

Precor

Precor Precision 400 Series User manual

Precor

Precor 9.41s User manual

Precor

Precor 9.31 User manual

Precor

Precor 9.33 Owner's manual

Precor

Precor Experience Series 700 Line User manual

Precor

Precor 9.33 User manual

Precor

Precor Experience 800 User manual

Precor

Precor 9.23 User manual

Precor

Precor PRECISION SERIES Technical manual

Precor

Precor C966 Instruction manual

Precor

Precor M9.45 User manual

Precor

Precor TRM. 600 User manual

Precor

Precor M9.45 User manual

Precor

Precor C954 Instruction manual

Precor

Precor M9.41si User manual

Popular Treadmill manuals by other brands

Treadly

Treadly TREADLY 2 user manual

HEALTH ONE

HEALTH ONE Walk Ro user manual

NordicTrack

NordicTrack NTL12941 user manual

NordicTrack

NordicTrack T7.5 S user manual

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 user manual

Merax

Merax MS282992 manual

FYTTER

FYTTER RU-2SX manual

FitLogic

FitLogic freewill d225 owner's manual

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB instruction manual

Horizon Fitness

Horizon Fitness Adventure 5 Plus Service manual

Stamia

Stamia InMotion II owner's manual

Smooth Fitness

Smooth Fitness EVO 3i user manual

NordicTrack

NordicTrack NETL81810.0 user manual

Schwinn

Schwinn 830/Journey 8.0 Assembly manual / owner's manual

Keys Fitness

Keys Fitness HealthTrainer HT-740T owner's manual

Spirit

Spirit XT8 Service manual

NordicTrack

NordicTrack T 14.0 Treadmill Manuel de l'utilisateur

Master

Master F22 user manual